Parent page: Working with Vault Components
Altium's Vault Data Acquisition feature provides a streamlined utility with which to essentially copy data between two Altium Vaults. The vehicle through which this is done - your interface to the Data Acquisition Service - is the Content Cart. This is control-central for defining what is to be acquired from the source vault, and transferred into the nominated target vault - a trusty removal van that 'carts' your nominated data between established vault residences.
Now there's no better way to illustrate the workings of a feature than by example. So to illustrate the ins-and-outs of the Content Cart, and its use in acquiring data, this article takes a look at acquiring some Component Items between the following vaults:
Accessing the Cart
Access to the Content Cart dialog is made from within the Vaults panel. While browsing the source vault from which you wish to obtain data, simply right-click on an Item Revision that you wish to acquire, and choose the Add to Content Cart command from the context menu. You can add one or more selected Item Revisions, or even a folder of Items. Initial access to the cart loads it with the Item Revision(s) that are selected in the source vault at the time of access:
- A single specific revision of an Item.
- Multiple specific revisions of the same Item.
- The latest revisions of multiple Items.
- The latest revisions of all Items in the selected folder (and its descendent structure). This allows you to load an entire folder onto the cart, while preserving its folder structure. To acquire a folder (and its descendant structure), simply select it in the Vault Folders region of the source vault (within the Vaults panel), then right-click and choose the Add to Content Cart command from the context menu.
An example of accessing the Content Cart.
The following Item types can be acquired from a source vault, into a target vault, using the Data Acquisition feature:
- 3D Model
- Simulation Model
- Managed Schematic Sheet
- Schematic Template
- Component Template
- Output Job
- Altium Designer Preferences
- Part Choice List
In addition, when acquiring a folder of items from the source vault, the following folder types are supported:
- Component Management Zone
- Component Library
- Generic Folder
Things to take into consideration when acquiring data:
- Only data Items in a released state in the source vault can be acquired.
- Only the chosen revision of a source Item is acquired, and not all revisions that may exist for that Item.
- When acquiring a revision of a source Component or Managed Schematic Sheet Item, all linked child Items will also be acquired:
- Component Item - applicable revisions of following linked child objects: Symbol Item, Footprint Item(s), 3D Model Item(s), Simulation Model Item, Component Template Item, Part Choice List Item.
- Managed Sheet Item - applicable revisions of following linked child objects: Component Item(s), Symbol Item(s), Footprint Item(s), 3D Model Item(s), Simulation Model Item(s), Component Template Item(s), Part Choice List Item(s), Schematic Template Item.
- The lifecycle of an acquired source Item revision will assume the initial 'post-release' state, as determined by the assigned lifecycle definition for the target Item. Any lifecycle history for the source Item revision will simply be ignored.
- If a child Item of a chosen source Component/Managed Schematic Sheet Item can not, for whatever reason, be acquired, then acquisition of that chosen Component/Managed Schematic Sheet Item will not proceed.
Specifying Source & Target Vaults
The two vaults involved in the acquisition are specified in the top region of the Content Cart dialog. The source vault is automatically determined, based on the residence of the Item Revision(s) you have specified to acquire. The target vault will be the Altium Vault that you are currently signed into. If connected to multiple local vaults, simply click on the target vault's name, or on the control to its right, to access a drop-down listing of currently connected local vaults. Switch vaults as required.
Specification of the source and target vaults, involved in the acquisition.
Naming the Cart
Acquired data from the source vault will be copied into new revisions of Items in the target vault. By default, these Items will be located in a defined, and newly-created folder structure within that vault. The top-level folder for this acquired content is named using the name of the cart itself. The default name is in the format
Content Cart - <Current Date> - <Current Time>, and is determined at the moment the cart is accessed. This can be changed to a more meaningful name as required by clicking the Change control, to the right of the cart's name.
Use the subsequent Content Cart Name Selection dialog to directly enter the preferred name for the cart. Alternatively, you can choose a folder in the target vault, into which content on the Cart is to be delivered. This can be an existing folder, or a completely new one, created on-the-fly. Simply browse to, and select an existing folder for the cart, using the Choose Folder dialog - accessed by clicking the button, at the far right of the Content Cart Name field. Or, create a new folder within the folder structure, using commands from the right-click menu.
A Content Cart can be named as required. Either change the name of the cart (which will be delivered into a top-level folder with that name), or choose to deposit the content
of the cart into an existing folder.
Specifying Items to Acquire
The main area of the Content Cart dialog presents an 'acquisition grid' - listing all Item Revisions that you have chosen to acquire from the source vault. Any number of Data Item Revisions can be 'loaded' onto the Content Cart for acquisition from the source vault. Initial access to the cart loads it with the Item Revision(s) that were selected in the source vault at the time of access, but any number of additional Items can be loaded. To do this, click the Add More Items control, at the top-right of the dialog. This gives access to the Choose Item dialog, from where you can choose one or more additional Item Revisions to acquire.
Remember, you can choose to add:
- A single specific revision of an Item.
- Multiple specific revisions of the same Item.
- The latest revisions of multiple Items.
- The latest revisions of all Items in the selected folder (and its descendent structure).
The main acquisition grid, listing all Item Revisions chosen for acquisition from the source vault.
With the source Item Revisions chosen, the Content Cart now has to be 'prepared for delivery' to the target vault. To do this, click the Prepare Cart button. This prepares the target vault for acquisition - checking the status of the chosen Item Revisions involved (in case they have been acquired previously), the parent-child links, and proposing the action to be taken. The results of this preparation phase are presented back in the main acquisition grid.
An example Content Cart, prepared ready for delivery to the target vault.
For each Item Revision involved in the acquisition, the Source region of the grid expands to present all applicable child Item Revisions and, optionally, the folder in which they reside within the source vault. For each Item Revision (parent and child alike) the following information can be presented in the Target region of the grid:
- Revision ID - the full identifier for the Item Revision in the target vault, based on defined Item Naming and Revision Scheme for that Item type.
- Folder - the destination folder in the target vault in which the acquired Item Revision will be created/delivered.
- Life Cycle - the lifecycle definition defined for the parent Item.
- Naming Scheme - the revision naming scheme defined for identifying revisions of the parent Item.
- Note - an optional note that can be used to provide useful information about the acquisition to others, when browsing the acquired content in your local vault.
- Status - the current state of the Item Revision in the target vault. Possible states are:
Not found - the Item Revision has never been acquired.
Already Exists - the Item Revision has been acquired previously.
- Action - the action that needs to be taken in order to achieve synchronization between source and target vaults. Possible actions are:
Transfer new revision and item - for completely new acquisitions, where the Item has never been acquired before. In other words, create an Item of that type and a new planned revision to accommodate the source data.
Transfer new revision - when acquiring another revision of an Item, and a revision of that Item has been acquired previously.
Nothing to do - the chosen Item Revision has already been acquired previously.
As part of the preparation phase, the cart uses default settings defined for each Item type that can be acquired. These settings are defined in the Content Cart Structure dialog, accessed by clicking the Change Settings control at the bottom-right of the Content Cart dialog.
Default acquisition settings are defined in the Content Cart Structure dialog.
These settings are used to determine the properties of newly-created Item Revisions in the target vault - created ready, and in the planned state, to receive data from the original Item Revisions in the source vault. They include a default folder in the target vault, as well as default Lifecycle Definition, Item and Revision Naming Schemes, and a starting index. A default note is also defined, in the format
Acquired from <SourceVaultName>.
In terms of destination folders in the target vault, each Item type will be acquired into a distinct folder under:
Modify these default acquisition settings in-line with schemes employed (and preferred!) for those Item types in your target vault. Click on a cell to access edit controls.
The acquisition settings in the Content Cart Structure dialog are coarse-level defaults. For Items that have never been acquired before - so the parent Item and initial revision are being newly-created (Action is
Transfer new revision and item) - properties at the individual Item-level can be defined if needed, giving finer-level control. To do so, simply select an Item Revision in the main acquisition grid, and click the Edit button. This will give you access to the Edit Item dialog, from where you can modify Item properties as required - overriding default settings.
For greater control, you can define properties at the individual Item level.
Once preparation is complete, click on the Deliver Cart button to proceed with the acquisition. A confirmation dialog will appear, notifying you that the Content Cart is about to be transferred from source to target vaults - click Yes to proceed. A second confirmation dialog will confirm the result of the acquisition, with the acquired Items available to browse in the target vault through the Vaults panel. If, before closing the Content Cart dialog, you run the preparation again - clicking Prepare Cart - the Status and Action fields will update to reflect the result - displaying
Already Exists and
Nothing to do, respectively.
Browsing the fruits of a successful acquisition.
Acquired data points back to its original source. This ancestral link information can be seen by changing the aspect view for the target Item Revision to its Origin aspect view. To quickly jump to the original source Item Revision, click the Show in Explorer button.
Each acquired Item Revision in the target vault links bank to its original source Item Revision in the source vault.
Acquiring Data in IntLib Format
You also have the ability to acquire components from your local Altium Vault, into an Integrated Library (*.IntLib). And when placing components from such an Integrated Library, the actual links are back to the Component Items in the vault. This gives you the ability to effectively use your company's vault components in an offline fashion, while ensuring the design still maintains a true connection to those components in the source vault.
Acquisition to an IntLib
From the Content Cart dialog, the process to acquire into an IntLib is as follows:
- Click on the Select target Vault link and choose IntLib file from the menu.
Set the target of the Content Cart to be an IntLib file.
- Specify the name, and location, for the generated IntLib file. By default, the file will be named in the format Integrated_Library - <Date> - <Time>.IntLib, and generated in the location \Users\Public\Documents\Altium\AD<Version>\Library\ExportCmpLib. Modify this as required through the Save As dialog - accessed by clicking the Change link.
Accept the default target folder, or change as required.
- If you need to acquire additional components into the same IntLib, click the Add More Items link, then use the subsequent Choose Item dialog to choose those components.
- Once ready, click the Deliver Cart button to proceed with generation of the IntLib. A temporary Integrated Library Package (*.LibPkg) will be created, with source SchLib (with symbols, parameters and model links) and PcbLib (with footprint models) files generated and added. This is then compiled to produce the IntLib file, which is generated in the specified folder. An information dialog will confirm successful generation of the file.
Deliver the cart to the target folder, which will contain the required Integrated Library file.
Use of the IntLib
After generation, the IntLib is added to the Installed Libraries list - part of the Available Libraries for the software. It will be available for use from the Libraries panel. Simply place components from the IntLib into your design as required. While effectively working with the components 'offline', the links back to the original vault components ensure continuity when you come back to working 'online' directly from your vault.
A generated IntLib, offering components acquired from your company vault. Once placed, the component is still linked back to the original vault component.