Parent page: PCB Objects
A pad is a primitive design object. Pads are used for fixing the component to the board, and to create the interconnection points from the component pins to the routing on the board. Pads can exist on a single layer, for example as a Surface Mount Device pad, or they can be a 3 dimensional through-hole pad, having a barrel-shaped body in the Z-plane (vertical), with a flat area on each (horizontal) copper layer. The barrel-shaped body of the pad is formed when the board is drilled and through-plated during fabrication. In the X and Y planes, pads can have a circular, rectangular, octagonal or rounded rectangular shape. Pads can be used individually as free pads in a design, or more typically, they are used in the PCB Library editor, where they are incorporated with other primitives into component footprints.
Pads are available for placement in both the PCB editor and the PCB Library editors, by selecting Place » Pad from the main menu, or by clicking the button in the wiring toolbar.
After launching the command, the cursor will change to a crosshair and you will enter pad placement mode.
Pads cannot have their properties modified graphically, other than their location.
The following methods of non-graphical editing are available:
Dialog page: Pad
This method of editing uses the following dialog to modify the properties of a pad object.
The Pad dialog can be accessed during placement by pressing the Tab key.
After placement, the dialog can be accessed in one of the following ways:
The hole can be round, square (punched), or a circular-ended slot. It can also be plated or unplated. Separate drill files (NC Drill Excellon format 2) are generated for each hole kind (Round, Square and Slot) as well as for plated and non-plated holes (as defined by the Plated checkbox). That means there can be up to six different drill files generated.
Each pad should be labeled with a designator, which is usually a component pin number. The designator can be up to 20 alphanumeric characters in length. Pad designators will auto-increment by 1 during placement if the initial pad has a designator ending with a numeric character. Press Tab to change the designator of the first pad prior to placement.
The layer drop-down is used to select the layer that the pad is present on. When designing a surface mount component footprint, set the Layer to
Top layer even if the component is intended to be used on the bottom side of the board. The software will automatically flip the pads' layer when the component is flipped to the bottom side of the board. For a standard, through-hole pad, set the Layer to
The Net field is used to define which net this pad is to connect to. Pads automatically connect to any internal power planes that are assigned to the same net. The pad will connect to the plane in accordance with the applicable Power Plane Connect Style design rule. If you do not want a pad to connect to power planes, add another Power Plane Connect Style design rule targeting the required pads, with a connection style of No Connect. Pads connect to polygon pours in accordance with the applicable Polygon Connect Style design rule.
If it is not physically possible (or desirable) to implement all connections as routing, for example on a single-sided PCB, then jumpers can be used. Within a component footprint, label the pads that are to be connected by a jumper with the same, non-zero, Jumper ID value. Pads that share the same Jumper ID and Net name tell the system that these pins will be connected by a physical jumper during PCB assembly, if that component also has a Type of
Jumper connections are shown as curved connection lines in the PCB editor. The Design Rules Checker will not report jumper connections as unrouted nets.
Use the Testpoint Settings to define this pad as a testpoint for Fabrication and/or Assembly. A testpoint is a location where a test probe can make contact with the PCB to check for correct function of the board. Any pad or via can be nominated as a testpoint, when this is done the component that the pad or via belongs to, automatically gets locked.
An opening in the paste and solder mask is automatically created by the software, the same shape as the pad. This opening can be larger (a positive expansion value) or smaller (a negative expansion value) than the pad itself, as defined by the Mask Expansion settings. Typically paste mask openings are smaller than the pad, while solder mask openings are larger than the pad, but there are exceptions to this. The default is for the pad to use the Expansion value from rules (the Paste Mask Expansion rule and the Solder Mask Expansion rule), this can be overridden and local values defined directly in the Pad dialog, if required.
The term tenting means to close off. If a tenting option is enabled then the settings in the applicable Solder Mask Expansion design rule will be overridden, resulting in no opening in the solder mask on that solder mask layer for this pad. When this option is enabled, the Expansion value from rules and the Specify expansion value options are ignored.
An Inspector panel enables the designer to interrogate and edit the properties of one or more design objects in the active document. Used in conjunction with appropriate filtering, the panel can be used to make changes to multiple objects of the same kind, from one convenient location.
Valid students can get their very own 6-month Altium Designer Student License for FREE! Just fill out the form below to request your Student License today.
好的，您可以下载免费的Altium Designer Viewer查看文档，有效期6个月。
好的，您可以下载免费的Altium Designer Viewer查看文档，有效期6个月。