Contact our corporate or local offices directly.
Parent page: More about Schematics
When schematics were originally captured on paper, it was often on a single sheet of paper large enough to fill a big drafting table, and reproduced by a dedicated large-format copier. Times have changed, now schematics are captured on a desktop PC, stored on a server, and printed on a small format laser printer.
This change means that even a simple design can be more easily displayed and understood if it is presented on multiple schematic sheets. Even when the design is not particularly complicated, there can be advantages in organizing it across multiple sheets.
For example, the design may include various modular elements. Maintaining these modules as individual documents allows several designers to work on a project at the same time. Breaking the design into logical modules greatly enhances the readability of the design too, an important consideration for those that need to read and interpret the schematic later in the life of that product. Another advantage is that when a design is structured over a number of sheets with fewer components on each, small format printing, such as laser printers, can be used.
There are two decisions to make if you plan to spread your design over multiple sheets:
Your choice will vary according to the size and type of each project, and your personal preferences.
As mentioned, as the designer you need to decide how the schematic sheets are organized, and how the connectivity is established between those sheets. These are not separate decisions though, as you choose the structure you will also need to choose how the connections between those sheets are going to be created.
There are two approaches to structuring a multi-sheet design: either flat or hierarchical.
You can think of a flat design as if a large schematic sheet has been cut up into a number of smaller sheets - in a flat design all sheets exist on the same level. The connectivity in a flat design is created directly from any sheet to any another sheet - this type of connectivity is referred to as horizontal connectivity.
The use of a top sheet is optional in a flat design. If one is included, it will have a sheet symbol for each of the sheets in the design, but cannot include any wiring. There can be any number of sheets in a flat design.
Both of the images above show a flat design, the version on the left does not have a top sheet, the version on the right does. For a small design that only has two or three schematic sheets in it, you might decide that a top sheet does not add any value. Once the sheet count gets higher, a top sheet can help the reader understand the functionality of the circuit design from the way that the logical blocks (Sheet Symbols) are arranged on the sheet. All sheets in the design appear at the same level in the Projects panel, because there is no hierarchy.
An hierarchical design is one which has Sheet Symbols to create the parent-child type relationships between the sheets, and, the connectivity is through the Sheet Entries in those Sheet Symbols - not directly from the Ports on one sheet to the Ports on another sheet.
As in a flat design, the child sheet is identified by defining its filename in the sheet symbol. In an hierarchical design that child sheet can also include sheet symbols, referencing lower-level sheets, thus creating another level in the hierarchy. The image below shows an hierarchical design, with 3 levels in the hierarchy.
In an hierarchical design, a signal on a child sheet leaves the sheet via a Port, which connects upward to a matching Sheet Entry on the parent sheet. The parent sheet includes wiring that carries the child signal across to a Sheet Entry in another Sheet Symbol, it then travels down to a matching Port on the second child sheet, as shown in the image below.
This parent-child sheet structure can be defined to any depth, and there can be any number of sheets in an hierarchical design.
As soon as you add a second schematic sheet to your project, you've created a multi-sheet design. If you are planning on creating a flat design without a top sheet, you simply keep adding schematic sheets to the project, and confirm that the Net Identifier Scope is set correctly.
If you want to use sheet symbols to reference lower-level sheets, you can either place the sheet symbol and manually edit it to correctly reference to the lower-level sheet, or you can use the various built-in commands to help, as described below.
It is the Filename property of the Sheet Symbol that references the lower-level sheet. Note that this field should only include the schematic filename, not the path to that file's location (this location data is actually stored in the Project file).
The software includes a number of commands that allow you to build your multi-document, hierarchical structure quickly and efficiently. The commands you use will depend on your personal design methodology - which can be broadly classified as top-down or bottom-up. These commands will be more efficient than creating the hierarchy manually, as they handle all the elements that are needed in the the process, such as adding Sheet Entries, creating new schematic sheets, placing Ports, and so on.
Use this command to build the hierarchy in a top-down fashion:
Use this command to build the hierarchy in a bottom-up fashion:
Use this command to reorganize how the circuity is placed in the design:
The process of design is often unstructured and organic, the designer could be formulating ideas for multiple parts of the design at the same time, capturing sections as their ideas evolve. That means that what started out as a well organized, neatly laid out set of schematics can become crowded and poorly organized. While you can Cut, Copy and Paste to reorganize the schematic design, this is not always the best approach. Why? Because as each component is placed it is assigned a unique identifier, and this identifier is automatically reset whenever a component is Cut/Copied and Pasted. This UID management is done to ensure that there is only one instance of each UID used in the design, as it is the key field that links the schematic component to the PCB component. The Cut/Copy/Paste approach is fine if the design has not been transferred to the PCB editor, but if it has, then it is better to use the refactor tools.
The easiest way to move a section of circuitry from one sheet to another is to select it, then run the Edit » Refactor » Move Selected Sub-circuit to Different Sheet command (also available via the right-click menu when there is a selection). The Choose Destination Document dialog will open, after you select the target sheet and click OK that sheet will appear, with the sub-circuit floating on the cursor, ready to position.
If you have moved components and wiring as part of restructuring the design, then you may also need to re-synchronize the child sheet to its Sheet Symbol, so that each Port has a matching Sheet Entry. This is done using the Synchronize Sheet Entries and Ports command, which is available in the:
For both of these commands, the Synchronize Ports to Sheet Entries dialog will open. It will list the already matched Ports/Sheet Entries on the right side of the dialog, with the unmatched Ports and Sheet Entries listed in two columns on the left side of the dialog.
Focusing on the mismatches displayed on the left of the dialog, the idea is to select the Sheet Entry in the first column, then the correct Port in the second column, then click the correct button to update one of them so they are synchronized (and move to the list on the right of the dialog). The buttons function as follows:
If multiple Sheet Entries are selected in the left-hand column, the software will synchronize each Sheet Entry with the adjacent Port in the second column. If there is no adjacent Port (or Sheet Entry), a new one is created.
It is not unusual for an electronic design to included repeated sections of circuitry. It might be a stereo amplifier, or it might be a 64 channel mixing desk. This type of design is fully supported in Altium Designer, by a feature-set known as multi-channel design.
In a multi-channel design you capture the repeated circuit once, then instruct the software to repeat it the required number of times. When the design is compiled it is expanded out in memory, with all components and connectivity repeated the required number of times, in accordance with a user-defined channel naming scheme.
The logical design that you capture is never actually flattened, the source always remains as a multi-channel schematic. When you transfer it to PCB layout, the physical components and nets are automatically stepped out the required number of times. You have full access to the standard cross-probing and cross-selecting tools available for working between the schematic and the PCB. There is also a tool in the PCB editor to replicate the placement and routing of one channel across all other channels, with the ability to easily move and re-orient an entire channel.
To understand multi-channel design, it helps to understand how the design data is managed. A fundamental element of the software is the Unified Data Model (UDM). When the project is compiled, a single, cohesive model is created, which sits central to the design process. Data within the model can then be accessed and manipulated using the various editors and services within the software. Rather than using a separate data store for each of the various design domains, the UDM is structured to accommodate all information from all aspects of the design, including the components and their connectivity.
The UDM, in combination with the hierarchical design system, is leveraged to deliver the multi-channel design capabilities. The "channel" is the circuitry within a Sheet Symbol - below this Sheet Symbol can be a single sheet, or it can be an entire branch of the project structure, containing other sub-sheets. You can also create channels within channels, in a 2-level multi-channel design the upper channels are referred to as banks, with the lower level ones referred to as channels.
Because this full, PCB-ready description exists in memory it is then possible to repeat a section of circuitry, as long as there is a systematic way to handle repeated objects, such as component designators and nets. The systematic naming is defined in the Multi-Channel tab of the Options for Project dialog, as discussed below.
A design is multi-channel when a section of the circuitry is repeated. This is done at the sheet symbol level, either by:
These two approaches to creating a multi-channel design are shown in the images above. In the image on the left there are four sheet symbols that all reference the same child sheet (
PortIO.SchDoc). In the image on the right, the
InputChannel.SchDoc is repeated 8 times and the
OutputChannel.SchDoc is repeated 2 times, by the presence of the Repeat keyword in the Designator field of the Sheet Symbol.
When the project is compiled, repeated component designators and net names are resolved by applying a standard naming scheme. For example, one naming scheme is to add a channel index to the repeated components and net identifiers (Net Labels and Ports), as shown in the highlights in the images below.
Note the tabs that appear across the bottom of the schematic when the project is compiled. The Editor tab contains the logical design as you have captured it, the other tabs (COUT1 and COUT2) appear once the project is compiled, they contain the physical design that will be transferred to the PCB editor. There will be a tab for each physical channel.
As mentioned, a channel is repeated by placing multiple sheet symbols that reference the same child sheet, or by including the
Repeat keyword in the Sheet Symbol's Designator field.
Each channel is identified by a channel designator, which comes from the Sheet Symbol Designator. When the design is channelized by placing multiple Sheet Symbols, the channel designator is the Designator value defined for each Sheet Symbol. If the design is channelized by the use of the Repeat keyword, the the channel designator is the
ChannelIdentifier+ChannelIndex defined by the
The syntax of the Designator field when the Repeat keyword is used, is as follows:
Note that the index range must start at 1, starting at 0 (zero) is not supported. When the Repeat keyword is used, the Sheet Symbol is drawn as a set of stacked Sheet Symbols.
The concept of being able to capture once and then repeat - multi-channel design - is delivered by building on the software's unified data model (UDM). Repeated components are named using a systematic naming scheme, which is configured in the Multi-Channel tab of the Options for Project dialog, as shown below.
The dialog includes an upper section used to control the naming of the Rooms, and a lower section used to control the naming of the components within those Rooms. At the Room level, there are 2 flat naming styles and 3 hierarchical naming styles, typically you would only need to choose an hierarchical naming style if the design has channels within channels. Otherwise, a flat Room naming style is shorter and easier to understand.
For the component naming, the
$Component$ChannelAlpha or the
$Component_$ChannelIndex option will give the shortest, and most easily interpreted component designation. It is also possible to construct your own designator naming scheme, using the available keywords.
A Room is a PCB design object used to define an area on the board, which can then be used in two ways:
Rooms work very well with multi-channel design. They can be created automatically as the design is transferred from the schematic editor to the PCB editor, based on options in the Class Generation tab of the Options for Project dialog, with a room for each Sheet Symbol. As well as clustering the components in that channel, the room can then be used in the naming of the components within that room. Rooms and their role in the board design process are discussed further in the Multi-Channel PCB Design section of this article.
For a multi-channel design, set the Net Identifier Scope to
Strict Hierarchical. A multi-channel design must be hierarchical because the software uses this structural model to instantiate the channels in memory when the design is compiled.
There are two different connectivity requirements that the software must support for a net connecting to a repeated channel, the net will either be:
The level of support for this depends on which method has been used to define the channels (multiple Sheet Symbols, or via the Repeat keyword). If a design uses multiple Sheet Symbols (an individual Sheet Symbol for each channel), then the net connectivity is explicit, as defined by the wiring placed by the designer.
If the design uses the Repeat keyword, then the following connectivity conventions apply.
|Passing a Net to all Channels||If a net needs to be available in all channels it is simply wired to a Sheet Entry, as shown for the
|Passing a net to a Specific Channel||To allocate a single net from a bus to each channel, the Repeat keyword is used in the Sheet Entry, as is shown for the
Ultimately, each net can only have one name on the PCB (one PCB net cannot have two names), and each net name should only be used once on the PCB (you should not have two different PCB nets with the same name). The software automatically resolves nets with multiple names to have just a single name when the project is compiled - it is important that you configure the naming options in a multi-channel design to ensure that your nets are labeled in a way that is meaningful to you. The net naming options are in the Netlist Options section of the Options tab of the Options for Project dialog.
A good approach to setting these options in a multi-channel design is to enable the Higher Level Names Take Priority option, and to also place Net Labels on all nets that connect to a channelized child sheet.
As an example, consider the images below. Note that both of the Sheet Symbols point to the sheet
PCB_Decoder.SchDoc, so there are 2 channels of this circuit, identified as U_PCB_DecoderA and U_PCB_DecoderB.
The Sheet Symbol includes a Sheet Entry called
TDI, which is the Test Data In line in a JTAG boundary scanning chain.
TDO (Test Data Out) from DecoderA then connects to the TDI of the next device in the chain, which is in the DecoderB channel.
When the project is compiled, the channel tabs U_PCB_DecoderA and U_PCB_DecoderB appear at the bottom of the schematic view, these tabs show the physical design as it will be passed to the PCB editor. In the images below, the schematic for the decoder circuit as it was captured, is shown in the Editor tab on the left below, followed by the two physical channels for that schematic, U_PCB_DecoderA and U_PCB_DecoderB.
In the original captured schematic, the net was labeled
TDI by the designer (first image). Note how the software has applied the higher-level net name,
TDO_CONTROLLER, in the DecoderA tab (second image), as it is a higher level net name (which has been set to have priority in this design). For DecoderB there is no higher-level name defined, so the original net name,
TDI, has been identified in this channel as
TDI_2 (third image) because that is the naming scheme defined in Multi-Channel tab of the Options for Project dialog (the Component Naming scheme is used to identify both components and nets within each channel).
Tracing and analyzing the nets in a multi-channel design can be confusing, as the names have to change to identify nets that are repeated, but continue to be unique. To help with this, there are a number of options to control the display of compiled object names, including component Designators, Net Labels and Ports. There are also options for Sheet and Document Numbers, these will be important when you are ready to generate print-type output.
The display of compiled object names is configured in the Schematic - Compiler page of the Preferences dialog, and are shown in the image below.
Typically you will want the designators and Net Labels displayed, Ports are handy if you are diagnosing an issue. If the Superscript option is enabled, the current document view will include the object identifier from the non-visible view as a superscript. Configure these to suit your preferences.
The schematic editor's error checking options default to flag every instance of a net with multiple names. This can occur when you intentionally change the name, for example when a net enters a sheet symbol and you prefer to use a different name within that sheet. The image below shows a number of examples of this, where the Left and Right outputs are bundled into a bus on the top sheet, but are called
Right in the Sheet Entries.
A bus has been used as it allows the two output channels to be represented by a single sheet symbol with a Repeat keyword. If separate wires were used for the Left and Right channels then the designer would have needed to place separate sheet symbols for the Left and Right output channels (both pointing to the same child schematic sheet), and then wire each output to its respective output sheet symbol.
You must instruct the software how to deal with multiple net identifiers. To do this, you will need to either:
When you transfer a design from the schematic editor to the PCB editor, the components from each sheet are clustered in a PCB placement room if Room creation is enabled in the Project Options.
The big advantage of using rooms in a multi-channel design is that the PCB editor supports duplicating the placement and routing from one room (channel), to the other rooms (channels). Rooms can also be moved as if they are a single object, simplifying the process of arranging the channels on the PCB.
Each schematic component links to its PCB component through a Unique Identifier (UID). The UID is assigned when the schematic component is placed on the sheet, and is then assigned to the PCB component when the design is transferred to the PCB editor. This scheme would be adequate for a simple design, but is not capable of supporting a multi-channel design, where the same schematic component is repeated in each physical channel (so the PCB components would have the same UID).
To cater for this, the UID for the PCB component is created by combining the UID of the parent Sheet Symbol with the UID of the schematic component. The syntax of the PCB UID changes slightly, depending on how the multi-channel design has been created.
For a multi-channel design created by placing multiple Sheet Symbols that all reference the same schematic sheet, then each Sheet Symbol can provide a unique ID, so the PCB UID has the format:
For a multi-channel design created using the Repeat keyword, there is only 1 Sheet Symbol UID available, so the PCB UID also includes the ChannelIndex, in the format:
It can be difficult positioning the designator strings in a multi-channel design, as they can be quite long. As well as choosing a naming option that results in a short name, another option is to display just the original, logical component designation instead. For example,
C30_CIN1 would display as
C30. This would require some other notation being added to the board to indicate the separate channels, such as a box being drawn around each channel on the component overlay.
You can select between Logical and Physical designator display on the PCB in the Board Options dialog (Design » Board Options). If you choose to display the logical designators for components in a multi-channel design, these will be displayed on the PCB and in any output generated, such as prints and Gerber's. The unique physical designators, however, are always used when generating a Bill of Materials.
The challenge with reusing a section of design, for example linking a Sheet Symbol on your current project to your company's preferred power supply schematic, is that the values of the components are not always fixed from one design to the next.
Parametric Hierarchical Design solves this - it allows you to move the specification of the component values from the schematic sheet, into the sheet symbol that references that sheet. This capability also works perfectly with multi-channel design, allowing you to have different component values in each channel. Note that it does require that each channel has its own Sheet Symbol, as this is where the component values are stored.
For example, a graphic equalizer can have the same circuit repeated many times, with the only difference between each channel being the component values. So a capacitor might take the values 0.12µF, 0.056µF, and 0.033µF in the different channels. Implementing this is simple, since you specify these values in the Sheet Symbol referencing each channel, eliminating the need to have many similar schematics with only the component values being different.
Parametric components are defined by declaring their value as a parameter of the sheet symbol above, and then referencing that parameter on the target component. The image below shows the top sheet for a graphic equalizer on the left, with the parameters of the 1KHz Sheet Symbol next to it. The image also shows the lower-level captured schematic, and the compiled 1KHz channel.
Each of those Sheet Symbol parameters is also defined as the value of a parameter in a schematic component on a lower-level sheet, as shown in the image below. When the project is compiled, the Value of each Sheet Symbol parameter is passed to the relevant schematic component, where it is then mapped into the component's Comment field.
Parametric hierarchy is not limited to component values, you can parametrically reference any component parameter or any text label on the schematic sheet. You can also refer to parameters from a symbol that is many sheets up in the hierarchy, the system will search the hierarchy until it finds the matching parameter.
Contact our corporate or local offices directly.
Please fill out the form below to get a quote for a new seat of Altium Designer.
If you are on Altium Subscription, you don’t need an evaluation license.
If you are not an active Altium Subscription member, please fill out the form below to get your free trial.
You came to the right place! Please fill out the form below to get your free trial started.
Valid students can get their very own 6-month Altium Designer Student License for FREE! Just fill out the form below to request your Student License today.
Got it. You can download a free Altium Designer Viewer license which is valid for a 6 months.
Please fill out the form below to request one.
That’s great! Making things is awesome. We have the perfect program for you.
Upverter is a free community-driven platform designed specifically to meet the needs of makers like you.
Click here to give it a try!
Got it. You can download a free Altium Designer Viewer license which is valid for a 6 months.
Please fill out the form below to request one.