Altium Designer Documentation

Clearance

Modified by by Admin on Apr 11, 2017
All Contents

Rule category: Electrical

Rule classification: Binary

Summary

This rule defines the minimum clearance allowed between any two primitive objects on a copper layer. Either a single value for clearance can be specified, or different clearances for different object pairings, through use of a dedicated Minimum Clearance Matrix. The latter, in combination with rule-scoping, provides the flexibility to build a concise and targeted set of clearance rules to meet even the most stringent of clearance needs.

Constraints

Default constraints for the Clearance rule.

  • Connective Checking– the scope of the rule with respect to the nets in the design. Can be set to one of the following:
    • Different Nets Only – constraint is applied between any two primitive objects belonging to different nets (e.g. two tracks on two different nets).
    • Same Net Only – constraint is applied between any two primitive objects belonging to the same net (e.g. between a via and pad on the same net, or within the same track of a differential pair).
    • Any Net – constraint is applied between any two primitive objects belonging to any net in the design. This is the most comprehensive of the three options and covers the possibility of the objects belonging to the same net or different nets.
    • Different Differential Pair - constraint is applied between any two primitive objects belonging to different nets of different differential pairs (e.g. a track in TX_P and a track in RX_P).
    • Same Differential Pair - constraint is applied between any two primitive objects belonging to different nets of the same differential pair (e.g. a track in TX_P and a track in TX_N).
  • Minimum Clearance – the value for the minimum clearance required. A value entered here will be replicated across all cells in the Minimum Clearance Matrix. Conversely, when a different clearance value is entered for one or more object pairings in the matrix, the Minimum Clearance constraint will change to N/A, to reflect that a single clearance value is not being applied across the board.
  • Minimum Clearance Matrix – provides the ability to fine tune clearances between the various object-to-object clearance combinations in the design.
The default Clearance rule for a new PCB document will default to use 10mil for all object-to-object clearance combinations. When creating a subsequent new clearance rule, the matrix will be populated with the values currently defined for the lowest priority Clearance rule.

Working with the Clearance Matrix

Definition of clearance values in the matrix can be performed in the following ways:

  • Single cell editing - to change the minimum clearance for a specific object pairing. Simply click on a cell to select it for editing.
  • Multi-cell editing - to change the minimum clearance for multiple object pairings:
    • Use Ctrl+click, Shift+click, and click&drag to select multiple cells in a column.
    • Use Shift+click, and click&drag to select multiple contiguous cells in a row.
    • Use click&drag to select multiple contiguous cells across multiple rows and columns
    • Click on a row header to quickly select all cells in that row.
    • Click on a column header to quickly select all cells in that column.
To set a single clearance value for all possible object pairings, simply set the required value for the Minimum Clearance constraint. On clicking Enter, this value will be replicated across all applicable cells of the matrix. Alternatively, click the blank grey cell at the top-left of the matrix, or use the Ctrl+A shortcut. This selects all cells in the matrix, ready to accommodate a newly-entered value.

With the required selection made (either a single cell or multiple cells), making a change to the current value is simply a case of typing the new value required. To submit the newly entered value, either click away on another cell, or press Enter. All cells in the selection will be updated with the new value.

Example multi-cell editing. Notice that as different values for clearance now exist for one or more object pairings, the Minimum Clearance constraint has changed to N/A, to reflect that a single clearance value is no longer being applied for all object-to-object clearance combinations.

How Duplicate Rule Contentions are Resolved

All rules are resolved by the priority setting. The system goes through the rules from highest to lowest priority and picks the first one whose scope expressions match the objects being checked.

Rule Application

Online DRC, Batch DRC, interactive routing, autorouting and during polygon placement.

Tips

  1. When defining the constraints for the rule, the Connective Checking option would typically be set to Different Nets Only. An example of when Same Net Only or Any Net could be used is to test for vias being placed too close to pads or other vias on the same net, or any other net.
  2. The minimum clearance matrix applies irrespective of the connective checking method specified. If different clearances are required between objects on the same net, to those defined for objects on different nets, be sure to define separate clearance rules as required to suit.
  3. The applicable use of the clearance matrix depends on the rule scoping. For example with scoping of ALL-ALL, all cells in the matrix are applicable (i.e. all possible object pairings). However, if scoping were set to IsVia-IsTrack, then only the single cell for the Via-Track object pairing would be applicable, and all other cells in the matrix left unused.
  4. When defining a clearance rule for a polygon, it is the primitives of the polygon that the rule is actually applied to, rather than the polygon itself. The keyword entry InPolygon (or InPoly) should be included in the Full Query in this case, instead of IsPolygon (or IsPoly). The specific polygon clearance rule must also be given a higher priority than any general clearance rule, if it is to have any effect.

 

Found an issue with this document? Highlight the area, then use Ctrl+Enter to report it.

Contact Us

Contact our corporate or local offices directly.

You are reporting an issue with the following selected text
and/or image within the active document:
ALTIUM DESIGNER FREE TRIAL
Altium Designer Free Trial
Let’s get started. First off, are you or your organization already using Altium Designer?

If would like to speak with a representative, please contact your local Altium office.
Copyright © 2019 Altium Limited

In that case, why do you need an evaluation license?

If would like to speak with a representative, please contact your local Altium office.
Copyright © 2019 Altium Limited

Got it. You actually don’t need an evaluation license for that.

Click the button below to download the latest Altium Designer installer.

Download Altium Designer Installer

If would like to speak with a representative, please contact your local Altium office.
Copyright © 2019 Altium Limited

Please fill out the form below to get a quote for a new seat of Altium Designer.

By clicking “Get Your Free Trial”, you are agreeing to our Privacy Policy.
You may receive communications from Altium and can change your notification preferences at any time.

If you are on Altium Subscription, you don’t need an evaluation license.

If you are not an active Altium Subscription member, please fill out the form below to get your free trial.

By clicking “Get Your Free Trial”, you are agreeing to our Privacy Policy.
You may receive communications from Altium and can change your notification preferences at any time.

Why are you looking to evaluate Altium Designer?

If would like to speak with a representative, please contact your local Altium office.
Copyright © 2019 Altium Limited

You came to the right place! Please fill out the form below to get your free trial started.

By clicking “Get Your Free Trial”, you are agreeing to our Privacy Policy.
You may receive communications from Altium and can change your notification preferences at any time.

Great News!

Valid students can get their very own 6-month Altium Designer Student License for FREE! Just fill out the form below to request your Student License today.

By clicking “Get Your Free Trial”, you are agreeing to our Privacy Policy.
You may receive communications from Altium and can change your notification preferences at any time.

Got it. You can download a free Altium Designer Viewer license which is valid for a 6 months.

Please fill out the form below to request one.

By clicking “Get Your Free Trial”, you are agreeing to our Privacy Policy.
You may receive communications from Altium and can change your notification preferences at any time.

That’s great! Making things is awesome. We have the perfect program for you.

Upverter is a free community-driven platform designed specifically to meet the needs of makers like you.

Click here to give it a try!

If would like to speak with a representative, please contact your local Altium office.
Copyright © 2019 Altium Limited

Got it. You can download a free Altium Designer Viewer license which is valid for a 6 months.

Please fill out the form below to request one.

By clicking “Get Your Free Trial”, you are agreeing to our Privacy Policy.
You may receive communications from Altium and can change your notification preferences at any time.