Altium Designer Documentation

Fabrication and Assembly Testpoint Usage

Modified by by Admin on Apr 11, 2017
This documentation page references Altium Vault, which is no longer a supported product. Altium Vault and its component management features have migrated to Altium Concord Pro.
All Contents

Rule category: Testpoint

Rule classification: Unary

Summary

The Fabrication Testpoint Usage and Assembly Testpoint Usage design rules specify which nets require testpoints for bare-board fabrication testing, or in-circuit assembly testing, respectively. The constraints between these two rules are identical.

Default Fabrication and Assembly Testpoint Usage rules exist. You should check whether these rules meet your board requirements and make changes as necessary.

When opening PCB designs or importing design rules created in a release of the software prior to the Summer 09 release, Testpoint Usage rules will become Fabrication Testpoint Usage rules.

Constraints

Default constraints for the Fabrication and Assembly Testpoint Usage rule.

  • Required – each target net must have a testpoint assigned. You can further sub-specify whether only a single testpoint is required for each net, or whether a testpoint is to be inserted at each 'leaf' node in a target net (pad/via locations that terminate a route). In addition, you can specify that a target net can have more testpoints, although these must be manually assigned.
  • Prohibited – each target net must not have a testpoint assigned.
  • Don't Care – each target net can have a testpoint assigned. It does not matter if a testpoint cannot be assigned to a net.

How Duplicate Rule Contentions are Resolved

All rules are resolved by the priority setting. The system goes through the rules from highest to lowest priority and picks the first one whose scope expression matches the object(s) being checked.

Rule Application

This rule is obeyed by the Testpoint Manager, Autorouter, the Online and Batch DRC, and during output generation.

Tips

  1. Fabrication and Assembly Testpoint reports can be configured and generated along with other fabrication and assembly outputs, as part of an Output Job Configuration file (*.OutJob). Use these reports to interrogate the locations of all valid fabrication and assembly testpoints, assigned in the design, respectively.
  2. Use the Testpoint Manager to identify the status of testpoint coverage for each net in a design, both in terms of bare-board fabrication and in-circuit assembly testing.
  3. A DRC report, obtained from running a Batch DRC, can be used to identify each net that fails this rule.

 

Found an issue with this document? Highlight the area, then use Ctrl+Enter to report it.

Contact Us

Contact our corporate or local offices directly.

You are reporting an issue with the following selected text
and/or image within the active document:
ALTIUM DESIGNER FREE TRIAL
Altium Designer Free Trial
Let’s get started. First off, are you or your organization already using Altium Designer?

If would like to speak with a representative, please contact your local Altium office.
Copyright © 2019 Altium Limited

In that case, why do you need an evaluation license?

If would like to speak with a representative, please contact your local Altium office.
Copyright © 2019 Altium Limited

Got it. You actually don’t need an evaluation license for that.

Click the button below to download the latest Altium Designer installer.

Download Altium Designer Installer

If would like to speak with a representative, please contact your local Altium office.
Copyright © 2019 Altium Limited

Please fill out the form below to get a quote for a new seat of Altium Designer.

By clicking “Get Your Free Trial”, you are agreeing to our Privacy Policy.
You may receive communications from Altium and can change your notification preferences at any time.

If you are on Altium Subscription, you don’t need an evaluation license.

If you are not an active Altium Subscription member, please fill out the form below to get your free trial.

By clicking “Get Your Free Trial”, you are agreeing to our Privacy Policy.
You may receive communications from Altium and can change your notification preferences at any time.

Why are you looking to evaluate Altium Designer?

If would like to speak with a representative, please contact your local Altium office.
Copyright © 2019 Altium Limited

You came to the right place! Please fill out the form below to get your free trial started.

By clicking “Get Your Free Trial”, you are agreeing to our Privacy Policy.
You may receive communications from Altium and can change your notification preferences at any time.

Great News!

Valid students can get their very own 6-month Altium Designer Student License for FREE! Just fill out the form below to request your Student License today.

By clicking “Get Your Free Trial”, you are agreeing to our Privacy Policy.
You may receive communications from Altium and can change your notification preferences at any time.

Got it. You can download a free Altium Designer Viewer license which is valid for a 6 months.

Please fill out the form below to request one.

By clicking “Get Your Free Trial”, you are agreeing to our Privacy Policy.
You may receive communications from Altium and can change your notification preferences at any time.

That’s great! Making things is awesome. We have the perfect program for you.

Upverter is a free community-driven platform designed specifically to meet the needs of makers like you.

Click here to give it a try!

If would like to speak with a representative, please contact your local Altium office.
Copyright © 2019 Altium Limited

Got it. You can download a free Altium Designer Viewer license which is valid for a 6 months.

Please fill out the form below to request one.

By clicking “Get Your Free Trial”, you are agreeing to our Privacy Policy.
You may receive communications from Altium and can change your notification preferences at any time.