PolylineArrowsAttributes

Created: August 04, 2017 | Updated: August 04, 2017 | Applies to versions: 18.0, 18.1, 19.0, 19.1, 20.0, 20.1 and 20.2

Parent page: Schematic Commands

The following pre-packaged resources, derived from this base command, are available:

Select Line Start/End Shape (None)

Applied Parameters: StartLineShape=None|EndLineShape=None

Summary

This command is used to change the selected polyline object to have no shape at its start and end.

Access

This command is accessed from the Schematic Editor by clicking the button on the Polyline Arrows Presets drop-down () of the Formatting toolbar.

Use

First, ensure that the polyline object(s) whose start/end shape you wish to change, are selected in the main design workspace.

After launching the command, all polyline objects will have their start and end shapes set to no shape, changing graphically in the workspace.

Tips

This feature is only available when the selected object is a polyline object, which has the requisite Start Line Shape, End Line Shape, and Line Shape Size properties.
You can select multiple polyline objects to have their line shape changed using this feature.
Greater control over these properties, and more, is available from the Properties panel, which presents the properties for the currently selected object.

Select Line Start/End Shape (Arrow/None, Small)

Applied Parameters: StartLineShape=Arrow|EndLineShape=None|LineShapeSize=Small

Summary

This command is used to change the selected polyline object to have a small arrow at its start and no shape at its end.

Access

This command is accessed from the Schematic Editor by clicking the button on the Polyline Arrows Presets drop-down () of the Formatting toolbar.

Use

First, ensure that the polyline object(s) whose start/end shape you wish to change, are selected in the main design workspace.

After launching the command, all polyline objects will have their start and end shapes set to small arrow and no shape respectively, changing graphically in the workspace.

Tips

This feature is only available when the selected object is a polyline object, which has the requisite Start Line Shape, End Line Shape, and Line Shape Size properties.
You can select multiple polyline objects to have their line shape changed using this feature.
Greater control over these properties, and more, is available from the Properties panel, which presents the properties for the currently selected object.

Select Line Start/End Shape (Arrow/Tail, Small)

Applied Parameters: StartLineShape=Arrow|EndLineShape=Tail|LineShapeSize=Small

Summary

This command is used to change the selected polyline object to have a small arrow at its start and a small tail at its end.

Access

This command is accessed from the Schematic Editor by clicking the button on the Polyline Arrows Presets drop-down () of the Formatting toolbar.

Use

First, ensure that the polyline object(s) whose start/end shape you wish to change, are selected in the main design workspace.

After launching the command, all polyline objects will have their start and end shapes set to small arrow and small tail respectively, changing graphically in the workspace.

Tips

This feature is only available when the selected object is a polyline object, which has the requisite Start Line Shape, End Line Shape, and Line Shape Size properties.
You can select multiple polyline objects to have their line shape changed using this feature.
Greater control over these properties, and more, is available from the Properties panel, which presents the properties for the currently selected object.

Select Line Start/End Shape (Arrow/Arrow, Small)

Applied Parameters: StartLineShape=Arrow|EndLineShape=Arrow|LineShapeSize=Small

Summary

This command is used to change the selected polyline object to have a small arrow at its start and end.

Access

This command is accessed from the Schematic Editor by clicking the button on the Polyline Arrows Presets drop-down () of the Formatting toolbar.

Use

First, ensure that the polyline object(s) whose start/end shape you wish to change, are selected in the main design workspace.

After launching the command, all polyline objects will have their start and end shapes set to small arrow, changing graphically in the workspace.

Tips

This feature is only available when the selected object is a polyline object, which has the requisite Start Line Shape, End Line Shape, and Line Shape Size properties.
You can select multiple polyline objects to have their line shape changed using this feature.
Greater control over these properties, and more, is available from the Properties panel, which presents the properties for the currently selected object.

Select Line Start/End Shape (Solid Arrow/None, Small)

Applied Parameters: StartLineShape=SolidArrow|EndLineShape=None|LineShapeSize=Small

Summary

This command is used to change the selected polyline object to have a small solid arrow at its start and no shape at its end.

Access

This command is accessed from the Schematic Editor by clicking the button on the Polyline Arrows Presets drop-down () of the Formatting toolbar.

Use

First, ensure that the polyline object(s) whose start/end shape you wish to change, are selected in the main design workspace.

After launching the command, all polyline objects will have their start and end shapes set to small solid arrow and no shape respectively, changing graphically in the workspace.

Tips

This feature is only available when the selected object is a polyline object, which has the requisite Start Line Shape, End Line Shape, and Line Shape Size properties.
You can select multiple polyline objects to have their line shape changed using this feature.
Greater control over these properties, and more, is available from the Properties panel, which presents the properties for the currently selected object.

Select Line Start/End Shape (Solid Arrow/Solid Tail, Small)

Applied Parameters: StartLineShape=SolidArrow|EndLineShape=SolidTail|LineShapeSize=Small

Summary

This command is used to change the selected polyline object to have a small solid arrow at its start and a small solid tail at its end.

Access

This command is accessed from the Schematic Editor by clicking the button on the Polyline Arrows Presets drop-down () of the Formatting toolbar.

Use

First, ensure that the polyline object(s) whose start/end shape you wish to change, are selected in the main design workspace.

After launching the command, all polyline objects will have their start and end shapes set to small solid arrow and small solid tail respectively, changing graphically in the workspace.

Tips

This feature is only available when the selected object is a polyline object, which has the requisite Start Line Shape, End Line Shape, and Line Shape Size properties.
You can select multiple polyline objects to have their line shape changed using this feature.
Greater control over these properties, and more, is available from the Properties panel, which presents the properties for the currently selected object.

Select Line Start/End Shape (Solid Arrow/Solid Arrow, Small)

Applied Parameters: StartLineShape=SolidArrow|EndLineShape=SolidArrow|LineShapeSize=Small

Summary

This command is used to change the selected polyline object to have a small solid arrow at its start and end.

Access

This command is accessed from the Schematic Editor by clicking the button on the Polyline Arrows Presets drop-down () of the Formatting toolbar.

Use

First, ensure that the polyline object(s) whose start/end shape you wish to change, are selected in the main design workspace.

After launching the command, all polyline objects will have their start and end shapes set to small solid arrow, changing graphically in the workspace.

Tips

This feature is only available when the selected object is a polyline object, which has the requisite Start Line Shape, End Line Shape, and Line Shape Size properties.
You can select multiple polyline objects to have their line shape changed using this feature.
Greater control over these properties, and more, is available from the Properties panel, which presents the properties for the currently selected object.

Select Line Start/End Shape (Circle/None, Small)

Applied Parameters: StartLineShape=Circle|EndLineShape=None|LineShapeSize=Small

Summary

This command is used to change the selected polyline object to have a small circle at its start and no shape at its end.

Access

This command is accessed from the Schematic Editor by clicking the button on the Polyline Arrows Presets drop-down () of the Formatting toolbar.

Use

First, ensure that the polyline object(s) whose start/end shape you wish to change, are selected in the main design workspace.

After launching the command, all polyline objects will have their start and end shapes set to small circle and no shape respectively, changing graphically in the workspace.

Tips

This feature is only available when the selected object is a polyline object, which has the requisite Start Line Shape, End Line Shape, and Line Shape Size properties.
You can select multiple polyline objects to have their line shape changed using this feature.
Greater control over these properties, and more, is available from the Properties panel, which presents the properties for the currently selected object.

Select Line Start/End Shape (Circle/Circle, Small)

Applied Parameters: StartLineShape=Circle|EndLineShape=Circle|LineShapeSize=Small

Summary

This command is used to change the selected polyline object to have a small circle at its start and end.

Access

This command is accessed from the Schematic Editor by clicking the button on the Polyline Arrows Presets drop-down () of the Formatting toolbar.

Use

First, ensure that the polyline object(s) whose start/end shape you wish to change, are selected in the main design workspace.

After launching the command, all polyline objects will have their start and end shapes set to small circle, changing graphically in the workspace.

Tips

This feature is only available when the selected object is a polyline object, which has the requisite Start Line Shape, End Line Shape, and Line Shape Size properties.
You can select multiple polyline objects to have their line shape changed using this feature.
Greater control over these properties, and more, is available from the Properties panel, which presents the properties for the currently selected object.

Select Line Start/End Shape (Square/None, Small)

Applied Parameters: StartLineShape=Square|EndLineShape=None|LineShapeSize=Small

Summary

This command is used to change the selected polyline object to have a small square at its start and no shape at its end.

Access

This command is accessed from the Schematic Editor by clicking the button on the Polyline Arrows Presets drop-down () of the Formatting toolbar.

Use

First, ensure that the polyline object(s) whose start/end shape you wish to change, are selected in the main design workspace.

After launching the command, all polyline objects will have their start and end shapes set to small square and no shape respectively, changing graphically in the workspace.

Tips

This feature is only available when the selected object is a polyline object, which has the requisite Start Line Shape, End Line Shape, and Line Shape Size properties.
You can select multiple polyline objects to have their line shape changed using this feature.
Greater control over these properties, and more, is available from the Properties panel, which presents the properties for the currently selected object.

Select Line Start/End Shape (Square/Square, Small)

Applied Parameters: StartLineShape=Square|EndLineShape=Square|LineShapeSize=Small

Summary

This command is used to change the selected polyline object to have a small square at its start and end.

Access

This command is accessed from the Schematic Editor by clicking the button on the Polyline Arrows Presets drop-down () of the Formatting toolbar.

Use

First, ensure that the polyline object(s) whose start/end shape you wish to change, are selected in the main design workspace.

After launching the command, all polyline objects will have their start and end shapes set to small square, changing graphically in the workspace.

Tips

This feature is only available when the selected object is a polyline object, which has the requisite Start Line Shape, End Line Shape, and Line Shape Size properties.
You can select multiple polyline objects to have their line shape changed using this feature.
Greater control over these properties, and more, is available from the Properties panel, which presents the properties for the currently selected object.

Select Line Start/End Shape (Arrow/None, Medium)

Applied Parameters: StartLineShape=Arrow|EndLineShape=None|LineShapeSize=Medium

Summary

This command is used to change the selected polyline object to have a medium arrow at its start and no shape at its end.

Access

This command is accessed from the Schematic Editor by clicking the button on the Polyline Arrows Presets drop-down () of the Formatting toolbar.

Use

First, ensure that the polyline object(s) whose start/end shape you wish to change, are selected in the main design workspace.

After launching the command, all polyline objects will have their start and end shapes set to medium arrow and no shape respectively, changing graphically in the workspace.

Tips

This feature is only available when the selected object is a polyline object, which has the requisite Start Line Shape, End Line Shape, and Line Shape Size properties.
You can select multiple polyline objects to have their line shape changed using this feature.
Greater control over these properties, and more, is available from the Properties panel, which presents the properties for the currently selected object.

Select Line Start/End Shape (Arrow/Tail, Medium)

Applied Parameters: StartLineShape=Arrow|EndLineShape=Tail|LineShapeSize=Medium

Summary

This command is used to change the selected polyline object to have a medium arrow at its start and medium tail at its end.

Access

This command is accessed from the Schematic Editor by clicking the button on the Polyline Arrows Presets drop-down () of the Formatting toolbar.

Use

First, ensure that the polyline object(s) whose start/end shape you wish to change, are selected in the main design workspace.

After launching the command, all polyline objects will have their start and end shapes set to medium arrow and medium tail respectively, changing graphically in the workspace.

Tips

This feature is only available when the selected object is a polyline object, which has the requisite Start Line Shape, End Line Shape, and Line Shape Size properties.
You can select multiple polyline objects to have their line shape changed using this feature.
Greater control over these properties, and more, is available from the Properties panel, which presents the properties for the currently selected object.

Select Line Start/End Shape (Arrow/Arrow, Medium)

Applied Parameters: StartLineShape=Arrow|EndLineShape=Arrow|LineShapeSize=Medium

Summary

This command is used to change the selected polyline object to have a medium arrow at its start and end.

Access

This command is accessed from the Schematic Editor by clicking the button on the Polyline Arrows Presets drop-down () of the Formatting toolbar.

Use

First, ensure that the polyline object(s) whose start/end shape you wish to change, are selected in the main design workspace.

After launching the command, all polyline objects will have their start and end shapes set to medium arrow, changing graphically in the workspace.

Tips

This feature is only available when the selected object is a polyline object, which has the requisite Start Line Shape, End Line Shape, and Line Shape Size properties.
You can select multiple polyline objects to have their line shape changed using this feature.
Greater control over these properties, and more, is available from the Properties panel, which presents the properties for the currently selected object.

Select Line Start/End Shape (Solid Arrow/None, Medium)

Applied Parameters: StartLineShape=SolidArrow|EndLineShape=None|LineShapeSize=Medium

Summary

This command is used to change the selected polyline object to have a medium solid arrow at its start and no shape at its end.

Access

This command is accessed from the Schematic Editor by clicking the button on the Polyline Arrows Presets drop-down () of the Formatting toolbar.

Use

First, ensure that the polyline object(s) whose start/end shape you wish to change, are selected in the main design workspace.

After launching the command, all polyline objects will have their start and end shapes set to medium solid arrow and no shape respectively, changing graphically in the workspace.

Tips

This feature is only available when the selected object is a polyline object, which has the requisite Start Line Shape, End Line Shape, and Line Shape Size properties.
You can select multiple polyline objects to have their line shape changed using this feature.
Greater control over these properties, and more, is available from the Properties panel, which presents the properties for the currently selected object.

Select Line Start/End Shape (Solid Arrow/Solid Tail, Medium)

Applied Parameters: StartLineShape=SolidArrow|EndLineShape=SolidTail|LineShapeSize=Medium

Summary

This command is used to change the selected polyline object to have a medium solid arrow at its start and medium solid tail at its end.

Access

This command is accessed from the Schematic Editor by clicking the button on the Polyline Arrows Presets drop-down () of the Formatting toolbar.

Use

First, ensure that the polyline object(s) whose start/end shape you wish to change, are selected in the main design workspace.

After launching the command, all polyline objects will have their start and end shapes set to medium solid arrow and medium solid tail respectively, changing graphically in the workspace.

Tips

This feature is only available when the selected object is a polyline object, which has the requisite Start Line Shape, End Line Shape, and Line Shape Size properties.
You can select multiple polyline objects to have their line shape changed using this feature.
Greater control over these properties, and more, is available from the Properties panel, which presents the properties for the currently selected object.

Select Line Start/End Shape (Solid Arrow/Solid Arrow, Medium)

Applied Parameters: StartLineShape=SolidArrow|EndLineShape=SolidArrow|LineShapeSize=Medium

Summary

This command is used to change the selected polyline object to have a medium solid arrow at its start and end.

Access

This command is accessed from the Schematic Editor by clicking the button on the Polyline Arrows Presets drop-down () of the Formatting toolbar.

Use

First, ensure that the polyline object(s) whose start/end shape you wish to change, are selected in the main design workspace.

After launching the command, all polyline objects will have their start and end shapes set to medium solid arrow, changing graphically in the workspace.

Tips

This feature is only available when the selected object is a polyline object, which has the requisite Start Line Shape, End Line Shape, and Line Shape Size properties.
You can select multiple polyline objects to have their line shape changed using this feature.
Greater control over these properties, and more, is available from the Properties panel, which presents the properties for the currently selected object.

Select Line Start/End Shape (Circle/None, Medium)

Applied Parameters: StartLineShape=Circle|EndLineShape=None|LineShapeSize=Medium

Summary

This command is used to change the selected polyline object to have a medium circle at its start and no shape at its end.

Access

This command is accessed from the Schematic Editor by clicking the button on the Polyline Arrows Presets drop-down () of the Formatting toolbar.

Use

First, ensure that the polyline object(s) whose start/end shape you wish to change, are selected in the main design workspace.

After launching the command, all polyline objects will have their start and end shapes set to medium circle and no shape respectively, changing graphically in the workspace.

Tips

This feature is only available when the selected object is a polyline object, which has the requisite Start Line Shape, End Line Shape, and Line Shape Size properties.
You can select multiple polyline objects to have their line shape changed using this feature.
Greater control over these properties, and more, is available from the Properties panel, which presents the properties for the currently selected object.

Select Line Start/End Shape (Circle/Circle, Medium)

Applied Parameters: StartLineShape=Circle|EndLineShape=Circle|LineShapeSize=Medium

Summary

This command is used to change the selected polyline object to have a medium circle at its start and end.

Access

This command is accessed from the Schematic Editor by clicking the button on the Polyline Arrows Presets drop-down () of the Formatting toolbar.

Use

First, ensure that the polyline object(s) whose start/end shape you wish to change, are selected in the main design workspace.

After launching the command, all polyline objects will have their start and end shapes set to medium circle, changing graphically in the workspace.

Tips

This feature is only available when the selected object is a polyline object, which has the requisite Start Line Shape, End Line Shape, and Line Shape Size properties.
You can select multiple polyline objects to have their line shape changed using this feature.
Greater control over these properties, and more, is available from the Properties panel, which presents the properties for the currently selected object.

Select Line Start/End Shape (Square/None, Medium)

Applied Parameters: StartLineShape=Square|EndLineShape=None|LineShapeSize=Medium

Summary

This command is used to change the selected polyline object to have a medium square at its start and no shape at its end.

Access

This command is accessed from the Schematic Editor by clicking the button on the Polyline Arrows Presets drop-down () of the Formatting toolbar.

Use

First, ensure that the polyline object(s) whose start/end shape you wish to change, are selected in the main design workspace.

After launching the command, all polyline objects will have their start and end shapes set to medium square and no shape respectively, changing graphically in the workspace.

Tips

This feature is only available when the selected object is a polyline object, which has the requisite Start Line Shape, End Line Shape, and Line Shape Size properties.
You can select multiple polyline objects to have their line shape changed using this feature.
Greater control over these properties, and more, is available from the Properties panel, which presents the properties for the currently selected object.

Select Line Start/End Shape (Square/Square, Medium)

Applied Parameters: StartLineShape=Square|EndLineShape=Square|LineShapeSize=Medium

Summary

This command is used to change the selected polyline object to have a medium square at its start and end.

Access

This command is accessed from the Schematic Editor by clicking the button on the Polyline Arrows Presets drop-down () of the Formatting toolbar.

Use

First, ensure that the polyline object(s) whose start/end shape you wish to change, are selected in the main design workspace.

After launching the command, all polyline objects will have their start and end shapes set to medium square, changing graphically in the workspace.

Tips

This feature is only available when the selected object is a polyline object, which has the requisite Start Line Shape, End Line Shape, and Line Shape Size properties.
You can select multiple polyline objects to have their line shape changed using this feature.
Greater control over these properties, and more, is available from the Properties panel, which presents the properties for the currently selected object.