製造にあたってのデザインの準備

現在、バージョン 1.0. をご覧頂いています。最新情報については、バージョン 製造にあたってのデザインの準備 の 5 をご覧ください。

This documentation page references Altium NEXUS/NEXUS Client (part of the deployed NEXUS solution), which has been discontinued. All your PCB design, data management and collaboration needs can now be delivered by Altium Designer and a connected Altium 365 Workspace. Check out the FAQs page for more information.

The final phase of the board design cycle is to generate the output files needed to fabricate, assemble and test the printed circuit board. To do this, you need to generate a variety of output files in a variety of formats.

The ultimate objective is to fabricate and assemble the board.
The ultimate objective is to fabricate and assemble the board.

As the designer, you have the choice of individually configuring and generating the outputs via the schematic and PCB editor's File and Reports menus, or alternatively, you can add all of the required outputs into an OutputJob and generate them from there.

This article summarizes the key elements of generating output from Altium NEXUS.

Altium NEXUS also provides a dedicated documentation editor - Draftsman. Draftsman has been built from the ground up as an environment for creating high-quality drawing-type documentation that can include dimensions, notes, layers stack tables, and drill tables. You can either continue to create drawing-type documentation using the approaches described here, or explore the documentation capabilities of Draftsman.


The OutputJob

An OutputJob, or OutJob for short, is essentially a container for individually configured outputs. The settings for these outputs are stored in the OutJob file, which is an ASCII file that becomes part of the project.

Using an OutputJob has a number of advantages:

  • All outputs are configured in, and generated from a single location.
  • Multiple outputs can be streamed into a single output file if required - for example, schematic prints and PCB layout prints can be output into the same PDF.
  • OutputJobs are used in a managed project, allowing for controlled release of the design.
  • OutputJob files can be copied from one project to another, insuring that your company's preferred output settings are always used.

A new OutputJob can be added to the project via the File » New sub-menu, or by right-clicking on the project in the Projects panel.

Read about Preparing Multiple Outputs in an OutputJob


Including Design Detail

Many of the outputs that you generate will require additional details. For example, the manufacturing drawing will need dimensions, the assembly drawing might need an enlarged view of a specific area of the board, and the fabrication drawing will need a Layer Stack Table and a Drill Table. These types of detail can be added in the PCB editor, or in Draftsman.

General Purpose Drawing Layers

In the PCB editor, detail such as dimensions, and fabrication and assembly instructions are added on mechanical layers. The software supports the addition of up to 32 general purpose mechanical layers, which are enabled in the View Configuration panel. These layers can be named as required (right-click on the name then select Edit Layer), and included in printouts and layer-based fabrication outputs.

Dimensions

The PCB editor includes a range of dimensioning tools, available in the Place » Dimension sub-menu. As you place a dimension, click on an existing object to attach the reference point to that object (press Shift+E to cycle through the object snap-to modes). The dimension will remain attached if that object is moved. Dimensions have a range of configuration options, offering a high-level of customization of the arrows and text.

During dimension placement, press the Spacebar to change the orientation of the dimension, and keep an eye on the Status bar for instructions on what to do next. Also, if you press Tab and edit the properties during placement, those settings will become the defaults for that dimension type.

Detailed dimensioning can also be placed in Draftsman.


Creating a Fabrication Panel

A printed circuit board is not fabricated as a single entity; typically a number of boards are fabricated on a panel. The panel can be defined by the fabricator, or alternatively, the board designer can create a panel in the PCB editor, using a feature referred to as an Embedded Board Array.

An Embedded Board Array is an object that you place into the PCB workspace and link to an existing board file. The Embedded Board Array stamps out the linked board from 1 to n times at the specified spacing. By placing multiple Embedded Board Arrays, you also can create a fabrication panel of different boards, or the same board can be laid out in a step and turn pattern.

The adjacent image shows a board repeated eight times in a step and turn pattern (alternate boards flipped). This was created by placing two Embedded Board Arrays; one with the boards facing up and the other with the boards flipped. The layer stack, dimensioning, V-groove, and route information has been added in this file rather than in the original source PCB.

Since the Embedded Board Array links to the source PCB, any design changes made in the source PCB are loaded into the Embedded Board Array the next time the array board file is opened.

Read about the Embedded Board Array

A key part of the panelization process is defining how the individual boards are to be separated. There are two common approaches: V-groove panelization or breakaway-tab panelization. V-groove panelization is inexpensive and effective for rectangular shaped boards; non-rectangular boards must use breakaway tabs.

To create breakaway-tab panelization, define a route tool path slot around the edge of each board, leaving small sections of remaining board that are perforated by a series of small holes, as shown in the adjacent image.

The route tool path is defined by placing track objects on a mechanical layer, which is then nominated as the Route Tool Path layer in the Properties panel (also shown in the image). Use the Create Primitives from Board Shape command to outline the board shape with tracks/arcs that define the route tool path, then edit them as required to create the breakaway tab regions. The breakaway tabs, also referred to as mouse bites, are created by placing a row of small unplated pads.

To learn more about panelization, read these excellent, detailed panelization guidelines, published on the Electronic Design website.


The Bill of Materials

Another key output document is the Bill of Materials. Rather than having a specific BOM generator, the software includes a powerful report generator. As well as being used to generate a BOM, it can also be configured to generate other component-type outputs, such as a component cross reference or a pick and place file.

BOM Report

Altium NEXUS includes a highly configurable report generator that is used to generate a detailed Bill of Materials. Referred to as the Report Manager, the dialog is used to:

  • Configure which design properties are to be included in the BOM.
  • Arrange the content in the order needed in the BOM.
  • Apply custom column-level, spreadsheet-like filters if required.
  • Enable different component source options.
  • Enable supplier options.
  • Configure the export file format.
  • Select an Excel BOM template, if the export format is XLS or PDF.

To use the BOM Report feature, add a Bill of Materials to the OutputJob and set the Data Source to [Project], which means the schematic project. For a pick and place file, the Data Source would be set to the [<BoardName>.PcbDoc].

Read about the Report Manager

ActiveBOM

ActiveBOM offers a more sophisticated approach to BOM management, allowing a customizable BOM to be developed during the design process. It is added as an additional project document (.BomDoc) and as well as the placed parts, it supports manually added components and BOM-specific data, for example; yet-to-be-detailed parts, fasteners, the blank board, or the mounting glue. Custom columns can also be added, including a specific Line number column, which offers both auto and manual numbering, with full copy/paste support.

Its greatest strength is that it is tightly coupled to the Altium Cloud Services, bringing live component costings right into the project, providing the designer with instant visibility to component availability and potential supply chain risks.

As with a standard BOM report, the actual ActiveBOM output is generated by adding a Bill of Materials in an OutputJob. Rather than selecting the [Project] as the Data Source in the OutputJob, instead you select [ActiveBOM Document] (or the ActiveBOM by name), as the Data Source.

Read about BOM management with ActiveBOM

Mapping Design Data into the BOM

Design data can be passed from Altium NEXUS into an Excel-format Bill Of Materials by including special statements in the Excel template that is used during BOM creation.

When creating the Bill of Materials template in Excel, a combination of Field and Column declarations can be used to specify the design properties that you want included in the BOM. Several example templates are provided with Altium NEXUS in the \Templates folder of the installation user-files.

Read about Including Design Data in the Excel BOM


Output Types

Because a variety of technologies and methods exist in PCB manufacture, the software has the ability to produce numerous output types for different purposes.

Output files are written to the following locations, for:

  • Individually generated outputs - to the location specified in the Output Path field in the Options tab of the Options for Project dialog.
  • OutputJob container - to the location specified in the Settings dialog. Use the links below to access the various container Settings dialogs.

Below is a summary of the available output types. Each output includes a link to the relevant setup/settings dialog:

Assembly Outputs

  • Assembly Drawings - component positions and orientations for each side of the board.
  • Pick and Place Files - used by robotic component placement machinery to place components onto the board. Note that the Report Generator can also be used to generate a Pick and Place file, and is highly configurable.
  • Test Point Report - as ASCII file, available in 3 formats, that details the location of each pad/via that has been nominated as a testpoint.

Documentation Outputs

  • PCB Prints - configure any number or printouts (pages), with any arrangement of layers and display of primitives, use this to create printed outputs such as assembly drawings.
  • PCB 3D Prints - views of the board from a three-dimensional view perspective.
  • PCB 3D Video - output a simple video of the board, based on a sequence of 3D key-frames defined in the PCB editor's PCB 3D Movie Editor panel.
  • PDF 3D - generate a 3D PDF view of the board, with full support to zoom, pan and rotate in Adobe Acrobat®. The PDF includes a model tree, giving control over the display of nets, components and the silkscreen. 
  • Schematic Prints - schematic drawings used in the design.

Fabrication Outputs

  • Composite Drill Drawings - drill positions and sizes (using symbols) for the board in one drawing.
  • Drill Drawing/Guides - drill positions and sizes (using symbols) for the board in separate drawings.
  • Final Artwork Prints - combines various fabrication outputs together as a single printable output.
  • Gerber Files - creates manufacturing information in Gerber format.
  • Gerber X2 Files - a new standard that encapsulates a high-level of design information, with backward compatibility to the original Gerber format.
  • IPC-2581 File - a new standard that encapsulates a high-level of design information within a single XML file.
  • NC Drill Files - creates manufacturing information for use by numerically controlled drilling machines.
  • ODB++ - creates manufacturing information in ODB++ database format.
  • Power-Plane Prints - creates internal and split plane drawings.
  • Solder/Paste Mask Prints - creates solder mask and paste mask drawings.
  • Testpoint Report - creates test point output for the design in a variety of formats.

Netlist Outputs

  • Netlists describe the logical connectivity between components in the design and are useful for transferring the design to other design platforms. A large variety of netlist formats are available. A small number are installed by default, the others require the installation of the Netlisters platform extension.

Report Outputs

  • Bill of Materials - use the report generator to create a list of parts and quantities (BOM), in various formats, required to manufacture the board.
  • Component Cross Reference Report - use the report generator to creates a list of components, based on the schematic sheet that they are on in the design.
  • Report Project Hierarchy - creates a list of source documents used in the project. This output has no setup options, the ASCII report is written to the specified output folder.
  • Report Single Pin Nets- creates a report listing any nets that only have one connection. This output has no setup options, the ASCII report is written to the specified output folder.
  • Simple BOM - creates text and CSV (comma separated variables) files of the BOM. This output has no setup options, the ASCII report is written to the specified output folder.
  • Electrical Rules Check - formatted report of the results of running an Electrical Rules Check. This output has no setup options, the ASCII report is written to the specified output folder.

Validation Outputs

The software includes a number of validation checks, which can be included as an output, during output generation. Each produces an HTML report file.

Note that the setup for these validation reports is held in the OutputJob. When you configure a validation check elsewhere in the software the settings are held with that file - for example the settings for project error checking are stored in the project file, PCB DRC settings are stored in the PCB file.

Export Outputs

The software is able to export data into a large number of formats. The options available in this section of the OutputJob will depend on which exporters are currently installed in Altium NEXUS. Exporters are installed in the Extensions and Updates view, they are provided either as platform extensions (supplied with the software, as a pre- or post-installation option), or as software extensions (extensions that are installed and managed separately from the core software).

PostProcess Outputs

This output type allows non-native Altium NEXUS file types to be included as part of the output. It copies the targeted files from within the project directory structure, to the folder specified in the configured Folder Structure output container. Files to be copied are configured in the Copy Files List Setup dialog - right-click on the Copy Files Job (added under the PostProcess Outputs heading) and select Configure, to open the dialog.

PCB Printouts

PCB printouts differ from other printouts, in that they can be configured to include any number of printouts (pages), and each printout can include any combination of layers used in the design, including mechanical and system layers. All printouts from the PCB are configured in the PCB Printout Properties dialog.

Tips on working in this dialog:

  • Right-click in the dialog to access commands to add a printout, add (or remove) a layer to a printout, or change the order of the layers in a printout. You can also Create a set of pre-defined printouts from the right-click menu, note that running one of the Create commands will remove any existing printouts.
  • Alternatively, double-click on a Printout to open the Printout Properties dialog, where you can also perform layer configuration actions; such as adding, deleting or moving one or many selected layers.
  • To rename a printout, select it, then press F2.
  • To edit how the various object types on a layer are to be rendered on the printout, double-click on the layer name.

Read more about the PCB Printout Properties dialog

Read more about the Configuring PCB Printouts


Output Formats and Output Containers

If you are generating output via the schematic or PCB editor menus, then the outputs are generated directly when you click OK in the relevant dialog. Use the links in the previous section to access the setup dialog for a specific output type.

If you are generating outputs via an OutputJob, the process is slightly different. In an OutputJob, each output you add and configure must then be mapped to an Output Container. The Output Container holds the setup for one of types of output formats, each of which is discussed below. When both the output and the container are configured, click the Generate content link in the Output Container to create that output.

To summarize:

  • Any number of new Output Containers can be added - click the Add New link at the bottom of each list.
  • Multiple outputs of the same output type can be mapped to the one Output Container.
  • To configure an Output Container, double-click on it, or click the Change link. A Settings dialog will open, there is link to each type of Settings dialog below.
  • The Output Container can be renamed - click once to select the output container, pause, then click a second time to edit the name.
  • Unless you are using the managed project feature, you should change the Output Management mode to [Manually Managed] in the appropriate Settings dialog.

PDF Output

The software includes a powerful PDF generator, which can be configured to create navigation bookmarks in the PDF file for the component designators and the nets. 

PDF's can also include bookmarks to the components and nets.
PDF's can also include bookmarks to the components and nets.

Schematic component parameters can also be included in the PDF, click on the component symbol in the PDF to display them. HelpURL and ComponentLinks can become links in the PDF, if they are defined in the Device Independent Path format, as described below.

Including Clickable Links from Component Parameters in a PDF

For links to work in a PDF, they must be defined using the Device Independent Path format - Acrobat requires this to ensure that links function in all operating systems. From within Altium NEXUS, both the Windows path format and the Device Independent Path format can be used in the HelpURL and ComponentLinks. If you want a link to work from within Acrobat, then it must be defined using the Device Independent Path format.

  • Windows path syntax: C:\MyFolder\MyFile.pdf
  • Device Independent path syntax: /C/MyFolder/MyFile.pdf

Include #page=<PageNumber> at the end of the link to open the target PDF at a specific page.

Read about PDF Settings

Files into a Folder Structure

Many of the output types generate their output in a specific, industry-standard format, such as ODB++, IPC-2581, or Gerber. The OutputJob Output Container for these output types is used to configure the naming and structure of the folders that are to be used for these output files. The Setup dialog also includes options to auto-open the output in Altium NEXUS's CAM editor.

Read about Folder Structure Settings

Video Output

This Output Container type is used for PCB 3D Video outputs. The Media Settings, including the video type and format, are configured in the Output Container.

Read about Video Settings

Printed Output

Printed output is not actually an Output Container, as the output is generated directly by the targeted printer. Double-click on the printer icon to configure the printer.

Why is my Output to Container Link Red

Each output setting must be mapped to a suitable container or hard copy output device, which you do by: selecting the output; then the container (or device); then clicking that output's Enable radio button. A green link will then be draw between that output and its container/device.

Sometimes when you create the link, it is shown in red instead of green. This indicates that there is a mismatch between the current page settings of the output, and the page settings available in the mapped container/device. To resolve this, right-click on the output and select Page Setup, then in the Properties dialog, ensure that the paper/page is set to a size that is also available in the container/device.

A red link indicates a mismatch between the page setup, and the page properties available in the chosen container.
A red link indicates a mismatch between the page setup, and the page properties available in the chosen container.


High Quality Documentation Output with Draftsman

Draftsman is an alternate way to create the graphical documents for board design production. Based on a dedicated file format and set of drawing tools, the Draftsman drawing system provides an interactive approach to bringing together fabrication and assembly drawings with custom templates, annotations, dimensions, callouts, and notes.

Key Draftsman features include:

  • Automated extraction of drawing data from the source PCB document.
  • Creation of multi-page documents.
  • Support for multiple drawing views (Assembly View, Fabrication View, Section View, or Drill Drawing View).
  • Assembly Views that include graphics generated from 3D Models.
  • Customizable Layer Stack Legend with the option to add detailed layer information.
  • Customizable BOM table.
  • Callouts to indicate BOM item positions or items from a Notes list.
  • Support of assembly Variants.

Read about Draftsman


Outputs and Managed Projects

For many designers, generating the output files from an OutputJob is the final stage of their work in Altium NEXUS.

However, there are also many designers that need to have tighter control over the design-to-release process, a requirement that can be met by creating the project as a managed project, and then releasing it using Altium NEXUS's formal managed board design release process. In this situation, the OutputJob acts as a output setup document, defining validation and output generation tasks that must be successfully performed for outputs to be generated.

Managed projects and the managed board design release process use the Altium Server for storage of the released output. The source for a managed project is stored in a repository controlled by the Server.

Read about Managed Projects and Releasing a Design

Read about Board Design Release


Where to Next

Preparing Multiple Outputs in an OutputJob

Configuring PCB Printouts

BOM Management with ActiveBOM

BOM Generation with the Report Manager

Design Documentation Generation with Draftsman

PDF3D Exporter

3D PCB Video

Board Design Release

 

If you find an issue, select the text/image and pressCtrl + Enterto send us your feedback.