Configuring PCB Standard Dimension Object Properties in Altium Designer

Вы просматриваете версию 19.1. Для самой новой информации, перейдите на страницу Configuring PCB Standard Dimension Object Properties in Altium Designer для версии 21
Applies to Altium Designer version: 19.1

Parent page: Standard Dimension

PCB Editor object properties are definable options that specify the visual style, content and behavior of the placed object. The property settings for each type of object are defined in two different ways:

  • Pre-placement settings – most Standard Dimension object properties, or those that can logically be pre-defined, are available as editable default settings on the PCB Editor - Defaults page of the Preferences dialog (access from the  button at the top-right of the workspace). Select the object in the Primitive List to reveal its options on the right.
  • Post-placement settings – all Standard Dimension object properties are available for editing in the Properties panel when a Standard Dimension is selected in the workspace.

The Standard Dimension default settings in the Preferences dialog and the Dimension mode of the Properties panel   The Standard Dimension default settings in the Preferences dialog and the Dimension mode of the Properties panel

In the below properties listing, options that are not available as default settings in the Preferences dialog are noted as "Properties panel only".

Style

  • Dimension Line Width - the current dimension line width.
  • Extension Line Height - the current extension line height.
  • Text Gap -the current gap to the left and right of the dimension value text. 

Properties

  • Layer - the layer to which the dimension is currently assigned. Dimensions can be assigned to any available layer. Use the drop-down to select a different layer.
  • Text Height - the current height of the dimension text characters. The character width used to display or print the text is automatically proportioned to this height. A minimum height of 36mil (0.9mm) will allow the text to be legibly photo-plotted.

Font Type

  • TrueType -  use this field to choose the required TrueType font. The drop-down list is populated with TrueType and OpenType (a superset of TrueType) fonts found in the \Windows\Fonts folder. Note, the list will only include entries for detected (and uniquely named) root fonts. Use the B (bold) and (italic) options to add emphasis to the text.
  • Stroke 
    • Font - use this field to choose the required Stroke font. Available options are:
      • Default - a simple vector font that supports pen plotting and vector photo-plotting.
      • Serif - a more complex font that will slow down vector output generation, such as Gerber.
      • Sans Serif - a more complex font that will slow down vector output generation, such as Gerber.
Stroke-based fonts are built into the software and cannot be changed. All three fonts have the full IBM extended ASCII character set that supports English and other European languages.
  • Stroke Width - displays the current stroke width. 

Units

  • Primary Units - the current unit that is selected for the calculation and display of the dimension value. Choose either MilsMillimetersInchesCentimeters, or Automatic.
The Automatic setting follows the actual measurement unit employed for the board as determined by the Units setting in the Other region of the Properties panel in Board mode.
  • Value Precision - the current setting for the number of decimal places to the right of the decimal point for which the dimension will be displayed.

Value

  • Format - the current setting for the format of the dimension text. Use the associated drop-down to change the format as required. The options listed will depend on the chosen Unit and present based on the actual value for the current dimension. In generic terms, the available options are:
    • None - no dimension text is displayed.
    • Value Only - no units are displayed, only the dimension value (e.g., 600.00).
    • Value and Unit - units are displayed after the dimension value (e.g., 600.00mil).
    • Value and Bracketed Unit - units are displayed in brackets after the dimension value (e.g., 600.00(mil)).
  • Sample - this field presents a sample of how the dimension text will appear in accordance with specified Format and any defined Prefix and/or Suffix.
  • Start point (X/Y) (Properties panel only) - the start point of the dimension for X (first value) and Y (second value).
  • End point (X/Y) (Properties panel only) - the end point of the dimension for X (first value) and Y (second value). 

 

Примечание

Доступные функциональные возможности зависят от вашего уровня Подписки на ПО Altium Designer.