The Basics of PDN for the PCB Designer

Created: February 10, 2017
Updated: January 4, 2021
The Basics of PDN for the PCB Designer

When PCB designers hear the term “PDN”, or “Power Distribution Network”, it might conjure up notions of bode plots, black magic, and other mysterious, scary things. In reality, the goal of the PDN is as straightforward as are most of the PCB design aspects that affect PDN performance. In this paper we’ll explain the various aspects of most PDN designs and how the PCB design software can influence them.

 

OVERALL GOAL: SUFFICIENT CURRENT AND VOLTAGE TO ALL THE LOADS

The fundamental goal of a Power Distribution Network is very straightforward - provide enough current and voltage to every load in order to meet their operation requirements. While the overall design of a PDN, including voltage regulators, on- die decoupling, packaging, mounting of components, etc., is a very challenging science that requires specialized training and experience, optimizing a PCB for PDN performance is less complicated since a PCB designer is limited in what they can do. In this paper, we’ll focus on what to consider within the PCB layout to ensure that your PCB design will provide sufficient current and voltage to all of your loads.

REQUIREMENT 1: SUFFICIENT METAL BETWEEN SOURCES AND LOADS

Ensuring there’s enough metal (usually copper) between each of the sources and their corresponding loads is the most critical aspect of PDN design. On the bright side, for a nominal cost, IPC-2152 provides fairly straightforward guidelines on how to do this. Given the maximum expected current and allowed temperature rise, the specification tells you what the minimum width should be for your power shape. Unfortunately, a designer only using IPC-2152 will be over-designing their PCB design software while being unaware of problems in their design, which comes with several limitations including:

- IPC-2152 width recommendations are very conservative. They represent calculations using data from a thermal worst-case scenario (2-layer board with no adjacent copper) and users typically make the most conservative assumptions (e.g., minimum allowed temperature rise). Designs made using only IPC-2152 may have much larger power shapes than necessary.

- IPC-2152 via recommendations are conservative. This is especially problematic since vias for one power rail might perforate the power shapes above and below, therefore via numbers and sizes should be optimized. Designs made using only IPC-2152 may have larger or more power vias than necessary.

Conservative Copper Pour

Conservative Copper Pour

- IPC-2152 only applies to the most straightforward design. A consistent width from source to load without any perforations from vias or constrictions from components and other shapes. IPC-2152 doesn’t give guidance on how to address imperfections in a design’s power shapes.

- IPC-2152 gives no insight into placement of associated power rails. Voltage regulators often have specific requirements for the various power shapes associated with them, from input to output, possibly including feedback.

Designers need better tools for optimizing the size and shape of their power (and ground) rails, commonly referred to as “PI-DC” or “IR Drop”. Altium has integrated this capability into their design environment with PDN Analyzer to make it as easy as possible to meet PDN requirements. Rather than relying on IPC-2152, a designer can analyze each power rail to see how much metal is appropriate, including aspects that IPC-2152 doesn’t address such as:

- Distance between the source and loads

- Allowed voltage drop between the source and loads

- Allowed current through connector pins

- Compensating for perforations or constrictions in the ground plane from vias, connectors, etc.

- Parts of the power or ground shapes that carry no current, making them candidates for - potential issues such as EMI failures and excessive crosstalk

- Efficiency of power and ground shapes

PDN Analyzer allows the designer to quickly and easily meet the most fundamental aspect of PDN design - optimizing the design of the metal between the sources and loads.

Design with Copper Peninsula and Islands in Blue

Design with Copper Peninsula and Islands in Blue

REQUIREMENT 2: CAPACITOR SIZES, VALUES, NUMBERS, AND PLACEMENT

The next aspect of the design under the PCB editor control is capacitor optimization. At first glance this might be intimidating since it involves frequency-dependent characteristics, which are much less intuitive than the PI-DC aspect. Fortunately, the complexity is limited by the number of parameters affecting capacitor efficiency that a PCB designer schematic can influence, including:

- Capacitor selection (sizes, values, and numbers)

- Capacitor placement

- Layer stackup

The last two are facets that the custom PCB designer can influence most and their optimization calls for observing specific guidelines, including (Bogatin, 2011):

- Spreading capacitors around the package of the load

- Close placement of capacitors

- Placing the power and ground planes of the power rail as close to the surface of the board as possible

- Using the thinnest dielectric possible between the power and ground planes

- Alternating the polarity of capacitor vias when they are in close proximity


Capacitor Placement Around Load Package

Capacitor Placement Around Load Package

There are also free tools available to aid the designer with capacitor optimization, including Rolf Ostergaard (www.pdntool.com) and Altera (as their “PDN tool”).

A NOTE ON DESIGN COMPLEXITY

There are more highly sophisticated power delivery systems, such as motor controllers with additional requirements like inductors, feedback loops, etc., that we won’t cover here. In these cases, more complex analysis tools and/or guidelines than most PCB designers have access to will be necessary.

Current Density Plot on Complex Rigid-Flex Design

Current Density Plot on Complex Rigid-Flex Design

THAT’S IT?

Design of a system-wide PDN solution meeting each source and load’s abilities and requirements is a very sophisticated science. But PDN Analyzer allows the PCB designing software to easily optimize power and ground shapes to use the least amount of real estate and components while increasing the reliability of a design.

Current Density Plot on Rigid-Flex Design

Current Density Plot on Rigid-Flex Design

 
Open as PDF

Related Resources

Back to Home
Thank you, you are now subscribed to updates.