Cypress Touch Controls

Now reading version 16.0. For the latest, read: Cypress Touch Controls for version 21
 

Facilitating the use of touch sensor technologies in your board designs, Altium Designer provides support for creating planar capacitive sensor patterns on your PCB, for use with the range of Cypress® CapSense® and PSoC® controllers.

Supported Sensors

The following self-capacitance sensor types are available for use in your PCB designs:

A button sensor is a zero-dimensional sensor. It has a single point of contact. Slider sensors are one-dimensional sensors – they detect movement of your finger along a single axis.

Each channel (electrode) of these sensors has a single, direct connection to the sensor controller. Such sensors are non-directional, in terms of their emitted electric fields. Although they can be used with or without an overlying panel, electrostatic discharge (ESD) implications – for the associated controller device – is a major influence for such a panel being used.

All of these sensors are suited for use with Cypress CapSense and PSoC controllers.

Installing Cypress CapSense Touch Sensor Support

If support has not already been added during initial installation of the software, it can be added from the Configure Platform page, when managing the extensions and updates for your installation (DXP » Extensions and Updates):

  1. From the Installed page of the view, simply click the Configure button at the top-right - to access the Configure Platform page.

First access the Configure Platform page of the Extensions & Updates view.First access the Configure Platform page of the Extensions & Updates view.

  1. Scroll to the bottom of the page and enable the entry for Cypress CapSense, in the Touch Sensor Support region of the page.

Then enable the Cypress CapSense option, under Touch Sensor Support.Then enable the Cypress CapSense option, under Touch Sensor Support.

  1. Click the Apply button, back at the top-right of the page. Altium Designer must be restarted for the changes to take effect, so click Yes at the dialog prompt. The required files will be downloaded and installed, and Altium Designer restarted. Verify through Windows Explorer that the Cypress CapSense.IntLib is now available - in the \Users\Public\Documents\Altium\AD<VersionNumber>\Library\CapSense folder (for a default installation).

After the installation is updated, the Cypress CapSense integrated library will be available.After the installation is updated, the Cypress CapSense integrated library will be available.

Sensor Implementation

A touch sensor is implemented in a design by placing and configuring the required sensor type from the dedicated Cypress CapSense integrated library (Cypress CapSense.IntLib).

The CapSense folder, and associated integrated library, will be present in the \Users\Public\Documents\Altium\AD<VersionNumber>\Library folder (for a default installation of Altium Designer), provided Cypress CapSense touch sensor support is installed as part of your Altium Designer installation, as detailed in the previous section.

When configured as required, simply update the target PCB – an ECO is used to effect the required changes, resulting in the creation of the sensor pattern for placement on the PCB. Each sensor component on the PCB isn't a footprint in the normal sense, but rather the actual copper electrode pattern. An overlaying panel would be placed over a sensor when the board is assembled.

Implementing a touch control is a snap - just place the required sensor type component on the schematic, configure it as applicable to your
design needs, then push the changes over to the PCB to obtain the sensor pattern.

A sensor pattern can also be modified on the PCB side, and the changes pushed back to the relevant schematic sheet through an ECO.

The following sections take a closer look at the configurable sensor components available for placement in a design, their configuration options, and the resulting sensor pattern obtained on the PCB side. In each case, the default configurations are presented.

As with all configurable schematic components in Altium Designer, access to the associated configuration dialog (CapSense Component dialog) for a sensor component is made by right-clicking over the component and choosing Configure from the context menu. Alternatively, click the Configure button from the associated properties dialog for the component.

CircularButton

Use the CircularButton component to implement a button sensor. This is a self-capacitance, zero-dimensional sensor, with a single channel for connection directly to a Cypress PSoC controller. The resulting sensor pattern on the PCB is a simple circular-shaped electrode.

Default configuration and resulting sensor pattern for the CircularButtonDefault configuration and resulting sensor pattern for the CircularButton component.

RectangularCurvedEdgeButton

Use the RectangularCurvedEdgeButton component to implement a button sensor. This is a self-capacitance, zero-dimensional sensor, with a single channel for connection directly to a Cypress PSoC controller. The resulting sensor pattern on the PCB is a simple rounded-rectangular-shaped electrode.

Default configuration and resulting sensor pattern for the RectangularCurvedEdgeButtonDefault configuration and resulting sensor pattern for the RectangularCurvedEdgeButton component.

LinearSlider

Use the LinearSlider component to implement an n-segment linear slider sensor. This is a self-capacitance, one-dimensional sensor for connection directly to a Cypress PSoC controller (each segment in the pattern connects to a separate pin of the Controller). The resulting sensor pattern on the PCB is comprised of a 1xn array of double-chevron-shaped electrodes, where n is the number of segments specified. In essence, you are specifying n separate sensors placed physically adjacent to each other. You have global control over the height and width of the constituent sensors. You can also control the gap between neighboring sensors.

Default configuration and resulting sensor pattern for the LinearSliderDefault configuration and resulting sensor pattern for the LinearSlider component.

RadialSlider

Use the RadialSlider component to implement an n-segment radial slider sensor. This is a self-capacitance, one-dimensional sensor for connection directly to a Cypress PSoC controller (each segment in the pattern connects to a separate pin of the Controller). The resulting sensor pattern on the PCB is comprised of n wedge-shaped electrodes, where n is the number of segments specified. In essence, you are specifying n separate sensors placed physically adjacent to each other in radial fashion. You have global control over the inner and outer diameter of the slider, and the clearance between neighboring segments.

Default configuration and resulting sensor pattern for the RadialSliderDefault configuration and resulting sensor pattern for the RadialSlider component.

Cypress Sensor Controllers

Cypress's CapSense Controllers – to which the corresponding electrodes from the sensor patterns connect – are based on the Programmable System-on-Chip (PSoC®) platform. CapSense Controller categories include:

  • CapSense®
  • CapSense® Plus
  • CapSense® Express
  • The families of PSoC® Controllers - PSoC® 1, PSoc® 3, PSoC® 4, and PSoC® 5LP (which replaced the PSoC® 5 family).

These controllers can be found on the Cypress CapSense Controllers, and relevant PSoC pages (PSoC 1, PSoC 3, PSoC 4, PSoC 5, PSoC 5LP) within the Unified Components section of the Design Content area of the Altium Website.

Browse CapSense Controller components on the Altium Website.Browse CapSense Controller components on the Altium Website.

Components can be browsed directly on these pages. In addition, each page offers the following two options:

  • Go To Vault - click this button to browse the components through the browser-based interface to the Altium Content Vault in which the components reside.
  • Download Library - click this button to download the components in a zipped integrated library file.

Alternatively, connect to the Altium Content Vault through Altium Designer and place components directly into your designs.

To connect to the vault, simply access the Data Management – Vaults page of the Preferences dialog, and click the Add Altium Content Vault button. Provided you have a licensed instance of Altium Designer and valid Altium Subscription, a connection to the vault will be made instantly. This direct connection enables you to access and place content from the Altium Content Vault directly into your designs, through the Vaults panel.

The CapSense Controllers can be found in the following vault folders:

  • Unified Components\Components\Cypress\Touch Sensing\Capsense Controllers
  • Unified Components\Components\Cypress\Programmable System-on-Chip\PSoC 1
  • Unified Components\Components\Cypress\Programmable System-on-Chip\PSoC 3
  • Unified Components\Components\Cypress\Programmable System-on-Chip\PSoC 4
  • Unified Components\Components\Cypress\Programmable System-on-Chip\PSoC 5
  • Unified Components\Components\Cypress\Programmable System-on-Chip\PSoC 5LP

Access the range of CapSense Controllers in the Altium Content Vault, available for placement in your designs through the Vaults panel.Access the range of CapSense Controllers in the Altium Content Vault, available for placement in your designs through the Vaults panel.

Further Information

For detailed information regarding Cypress's capacitive touch sensor design, see www.cypress.com/products/capsense-controllers.

 

If you find an issue, select the text/image and pressCtrl + Enterto send us your feedback.
Note

The features available depend on your Altium product access level. Compare features included in the various levels of Altium Designer Software Subscription and functionality delivered through applications provided by the Altium 365 platform.

If you don’t see a discussed feature in your software, contact Altium Sales to find out more.

Content