Altium Designer Documentation

FoldUnfold

Modified by Jason Howie on Jun 13, 2017

Parent page: PCB Commands

The following pre-packaged resource, derived from this base command, is available:


Applied Parameters: None

Summary

This command is used in 3D Layout Mode to toggle a board that has flexible areas between its flattened state (no Bending Line settings applied), and its folded state (all Bending Line settings applied). This 'folding' is made possible through the placement of one or more Bending Lines within the flex region(s) of the board. The Bending Line defines where on the surface of the flex region that the bend is to take place. The Bending Line also defines the angle and radius of the bend, and the width of the strip of board surface that is being bent.

Access

This command can be accessed from the PCB Editor, when in 3D Layout Mode, by:

  • Choosing the View » Fold/Unfold command, from the main menus.
  • Using the 5 keyboard shortcut.

Use

First ensure that the PCB Editor is placed in 3D Layout Mode. This can be done by choosing the View » 3D Layout Mode command, from the main menus, or by using the 3 keyboard shortcut.

After launching the command, the board will either be folded or flattened, depending on whether it is currently in the flattened state or not. Folding is performed along defined Bending Lines, and in accordance with any specified bending sequence.

The Bending Lines defined for a particular stackup region of the board, and their sequence, can be seen and managed from the Bending Lines region of the PCB panel, when configured in Layer Stack Regions mode. Double-click a Bending Line entry to access the Bending Line dialog, from where its properties can be set. This includes being able to define the fold sequence through use of the Fold Index option. Sequence values (Fold Index values) that are the same, are applied at the same time during folding.

Tips

  1. To be able to interrogate the folding of your board in greater detail, with the ability to effectively fold in slow-motion and pause folding, use the Fold State slider control, located beneath the Bending Lines region of the PCB panel, when configured in Layer Stack Regions mode. Note that one board region must have its Lock 3D Position option enabled (in the Stackup Regions region of the panel). This option can also be enabled in the Board Region dialog, where it is presented as the 3D Locked option. This is required to define the physical ground reference for the 3D display mode (where Z = 0). If this is not done, bends will not be applied when you move the Fold State slider.
  2. A Bending Line can only be placed on a region that is configured as a Flex region in the Layer Stack Manager dialog. When a board region is set to use a Flex layer stack, a Bending Line is automatically added, vertically down its geometric center. Remove, or reposition and configure this Bending Line as required.

 

Found an issue with this document? Highlight the area, then use Ctrl+Enter to report it.

Contact Us

Contact our corporate or local offices directly.

You are reporting an issue with the following selected text
and/or image within the active document:
ALTIUM DESIGNER FREE TRIAL
Altium Designer Free Trial
Let’s get started. First off, are you or your organization already using Altium Designer?

If would like to speak with a representative, please contact your local Altium office.
Copyright © 2019 Altium Limited

In that case, why do you need an evaluation license?

If would like to speak with a representative, please contact your local Altium office.
Copyright © 2019 Altium Limited

Got it. You actually don’t need an evaluation license for that.

Click the button below to download the latest Altium Designer installer.

Download Altium Designer Installer

If would like to speak with a representative, please contact your local Altium office.
Copyright © 2019 Altium Limited

Please fill out the form below to get a quote for a new seat of Altium Designer.

By clicking “Get Your Free Trial”, you are agreeing to our Privacy Policy.
You may receive communications from Altium and can change your notification preferences at any time.

If you are on Altium Subscription, you don’t need an evaluation license.

If you are not an active Altium Subscription member, please fill out the form below to get your free trial.

By clicking “Get Your Free Trial”, you are agreeing to our Privacy Policy.
You may receive communications from Altium and can change your notification preferences at any time.

Why are you looking to evaluate Altium Designer?

If would like to speak with a representative, please contact your local Altium office.
Copyright © 2019 Altium Limited

You came to the right place! Please fill out the form below to get your free trial started.

By clicking “Get Your Free Trial”, you are agreeing to our Privacy Policy.
You may receive communications from Altium and can change your notification preferences at any time.

Great News!

Valid students can get their very own 6-month Altium Designer Student License for FREE! Just fill out the form below to request your Student License today.

By clicking “Get Your Free Trial”, you are agreeing to our Privacy Policy.
You may receive communications from Altium and can change your notification preferences at any time.

Got it. You can download a free Altium Designer Viewer license which is valid for a 6 months.

Please fill out the form below to request one.

By clicking “Get Your Free Trial”, you are agreeing to our Privacy Policy.
You may receive communications from Altium and can change your notification preferences at any time.

That’s great! Making things is awesome. We have the perfect program for you.

Upverter is a free community-driven platform designed specifically to meet the needs of makers like you.

Click here to give it a try!

If would like to speak with a representative, please contact your local Altium office.
Copyright © 2019 Altium Limited

Got it. You can download a free Altium Designer Viewer license which is valid for a 6 months.

Please fill out the form below to request one.

By clicking “Get Your Free Trial”, you are agreeing to our Privacy Policy.
You may receive communications from Altium and can change your notification preferences at any time.