SnapGrid

Последнее изменение: Jason Howie; 11.04.2017

Parent page: CAMtastic Commands

The following pre-packaged resources, derived from this base command, are available:


Applied Parameters: Size=1Mil

Summary

This command is used to set the X (horizontal) and Y (vertical) step values - for the Snap Grid - simultaneously to 1mil. These values together define the Snap Grid for manual movement and placement in the current document.

Access

This command is accessed from the CAMtastic Editor, by:

  • Using the G keyboard shortcut, then choosing the 1 Mil command from the pop-up menu.
  • Choosing the 1 Mil entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for both the X Grid and Y Grid properties of the Snap Grid will be set to 1mil, and the grid will update accordingly in the workspace.

Tips

  1. The X and Y grid values can be changed as required, and independently for the snap grid, by editing the grid through the Enter Grid (1..1000mil) dialog, accessed by using the Ctrl+G keyboard shortcut.
  2. Display of the grid (On/Off), as well as grid sizing (Size X:Y), can also be managed from the CAM Editor - Drawing Modes page of the Preferences dialog. The size drop-down field lists previously used grid values, or simply enter new sizing directly, as required.
  3. The snap grid is used when the Object Snap mode is set to Grid. The object snapping mode can be changed on the CAMtastic panel, or on the CAM Editor - Drawing Modes page of the Preferences dialog. With the mode set to Grid, the cursor automatically snaps to the grid, positioning the reference point of the object being placed onto the nearest grid location.


Applied Parameters: Size=5Mil

Summary

This command is used to set the X (horizontal) and Y (vertical) step values - for the Snap Grid - simultaneously to 5mil. These values together define the Snap Grid for manual movement and placement in the current document.

Access

This command is accessed from the CAMtastic Editor, by:

  • Using the G keyboard shortcut, then choosing the 5 Mil command from the pop-up menu.
  • Choosing the 5 Mil entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for both the X Grid and Y Grid properties of the Snap Grid will be set to 5mil, and the grid will update accordingly in the workspace.

Tips

  1. The X and Y grid values can be changed as required, and independently for the snap grid, by editing the grid through the Enter Grid (1..1000mil) dialog, accessed by using the Ctrl+G keyboard shortcut.
  2. Display of the grid (On/Off), as well as grid sizing (Size X:Y), can also be managed from the CAM Editor - Drawing Modes page of the Preferences dialog. The size drop-down field lists previously used grid values, or simply enter new sizing directly, as required.
  3. The snap grid is used when the Object Snap mode is set to Grid. The object snapping mode can be changed on the CAMtastic panel, or on the CAM Editor - Drawing Modes page of the Preferences dialog. With the mode set to Grid, the cursor automatically snaps to the grid, positioning the reference point of the object being placed onto the nearest grid location.


Applied Parameters: Size=10Mil

Summary

This command is used to set the X (horizontal) and Y (vertical) step values - for the Snap Grid - simultaneously to 10mil. These values together define the Snap Grid for manual movement and placement in the current document.

Access

This command is accessed from the CAMtastic Editor, by:

  • Using the G keyboard shortcut, then choosing the 10 Mil command from the pop-up menu.
  • Choosing the 10 Mil entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for both the X Grid and Y Grid properties of the Snap Grid will be set to 10mil, and the grid will update accordingly in the workspace.

Tips

  1. The X and Y grid values can be changed as required, and independently for the snap grid, by editing the grid through the Enter Grid (1..1000mil) dialog, accessed by using the Ctrl+G keyboard shortcut.
  2. Display of the grid (On/Off), as well as grid sizing (Size X:Y), can also be managed from the CAM Editor - Drawing Modes page of the Preferences dialog. The size drop-down field lists previously used grid values, or simply enter new sizing directly, as required.
  3. The snap grid is used when the Object Snap mode is set to Grid. The object snapping mode can be changed on the CAMtastic panel, or on the CAM Editor - Drawing Modes page of the Preferences dialog. With the mode set to Grid, the cursor automatically snaps to the grid, positioning the reference point of the object being placed onto the nearest grid location.


Applied Parameters: Size=20Mil

Summary

This command is used to set the X (horizontal) and Y (vertical) step values - for the Snap Grid - simultaneously to 20mil. These values together define the Snap Grid for manual movement and placement in the current document.

Access

This command is accessed from the CAMtastic Editor, by:

  • Using the G keyboard shortcut, then choosing the 20 Mil command from the pop-up menu.
  • Choosing the 20 Mil entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for both the X Grid and Y Grid properties of the Snap Grid will be set to 20mil, and the grid will update accordingly in the workspace.

Tips

  1. The X and Y grid values can be changed as required, and independently for the snap grid, by editing the grid through the Enter Grid (1..1000mil) dialog, accessed by using the Ctrl+G keyboard shortcut.
  2. Display of the grid (On/Off), as well as grid sizing (Size X:Y), can also be managed from the CAM Editor - Drawing Modes page of the Preferences dialog. The size drop-down field lists previously used grid values, or simply enter new sizing directly, as required.
  3. The snap grid is used when the Object Snap mode is set to Grid. The object snapping mode can be changed on the CAMtastic panel, or on the CAM Editor - Drawing Modes page of the Preferences dialog. With the mode set to Grid, the cursor automatically snaps to the grid, positioning the reference point of the object being placed onto the nearest grid location.


Applied Parameters: Size=25Mil

Summary

This command is used to set the X (horizontal) and Y (vertical) step values - for the Snap Grid - simultaneously to 25mil. These values together define the Snap Grid for manual movement and placement in the current document.

Access

This command is accessed from the CAMtastic Editor, by:

  • Using the G keyboard shortcut, then choosing the 25 Mil command from the pop-up menu.
  • Choosing the 25 Mil entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for both the X Grid and Y Grid properties of the Snap Grid will be set to 25mil, and the grid will update accordingly in the workspace.

Tips

  1. The X and Y grid values can be changed as required, and independently for the snap grid, by editing the grid through the Enter Grid (1..1000mil) dialog, accessed by using the Ctrl+G keyboard shortcut.
  2. Display of the grid (On/Off), as well as grid sizing (Size X:Y), can also be managed from the CAM Editor - Drawing Modes page of the Preferences dialog. The size drop-down field lists previously used grid values, or simply enter new sizing directly, as required.
  3. The snap grid is used when the Object Snap mode is set to Grid. The object snapping mode can be changed on the CAMtastic panel, or on the CAM Editor - Drawing Modes page of the Preferences dialog. With the mode set to Grid, the cursor automatically snaps to the grid, positioning the reference point of the object being placed onto the nearest grid location.


Applied Parameters: Size=50Mil

Summary

This command is used to set the X (horizontal) and Y (vertical) step values - for the Snap Grid - simultaneously to 50mil. These values together define the Snap Grid for manual movement and placement in the current document.

Access

This command is accessed from the CAMtastic Editor, by:

  • Using the G keyboard shortcut, then choosing the 50 Mil command from the pop-up menu.
  • Choosing the 50 Mil entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for both the X Grid and Y Grid properties of the Snap Grid will be set to 50mil, and the grid will update accordingly in the workspace.

Tips

  1. The X and Y grid values can be changed as required, and independently for the snap grid, by editing the grid through the Enter Grid (1..1000mil) dialog, accessed by using the Ctrl+G keyboard shortcut.
  2. Display of the grid (On/Off), as well as grid sizing (Size X:Y), can also be managed from the CAM Editor - Drawing Modes page of the Preferences dialog. The size drop-down field lists previously used grid values, or simply enter new sizing directly, as required.
  3. The snap grid is used when the Object Snap mode is set to Grid. The object snapping mode can be changed on the CAMtastic panel, or on the CAM Editor - Drawing Modes page of the Preferences dialog. With the mode set to Grid, the cursor automatically snaps to the grid, positioning the reference point of the object being placed onto the nearest grid location.


Applied Parameters: Size=100Mil

Summary

This command is used to set the X (horizontal) and Y (vertical) step values - for the Snap Grid - simultaneously to 100mil. These values together define the Snap Grid for manual movement and placement in the current document.

Access

This command is accessed from the CAMtastic Editor, by:

  • Using the G keyboard shortcut, then choosing the 100 Mil command from the pop-up menu.
  • Choosing the 100 Mil entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for both the X Grid and Y Grid properties of the Snap Grid will be set to 100mil, and the grid will update accordingly in the workspace.

Tips

  1. The X and Y grid values can be changed as required, and independently for the snap grid, by editing the grid through the Enter Grid (1..1000mil) dialog, accessed by using the Ctrl+G keyboard shortcut.
  2. Display of the grid (On/Off), as well as grid sizing (Size X:Y), can also be managed from the CAM Editor - Drawing Modes page of the Preferences dialog. The size drop-down field lists previously used grid values, or simply enter new sizing directly, as required.
  3. The snap grid is used when the Object Snap mode is set to Grid. The object snapping mode can be changed on the CAMtastic panel, or on the CAM Editor - Drawing Modes page of the Preferences dialog. With the mode set to Grid, the cursor automatically snaps to the grid, positioning the reference point of the object being placed onto the nearest grid location.


Applied Parameters: Size=200Mil

Summary

This command is used to set the X (horizontal) and Y (vertical) step values - for the Snap Grid - simultaneously to 200mil. These values together define the Snap Grid for manual movement and placement in the current document.

Access

This command is accessed from the CAMtastic Editor, by:

  • Using the G keyboard shortcut, then choosing the 200 Mil command from the pop-up menu.
  • Choosing the 200 Mil entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for both the X Grid and Y Grid properties of the Snap Grid will be set to 200mil, and the grid will update accordingly in the workspace.

Tips

  1. The X and Y grid values can be changed as required, and independently for the snap grid, by editing the grid through the Enter Grid (1..1000mil) dialog, accessed by using the Ctrl+G keyboard shortcut.
  2. Display of the grid (On/Off), as well as grid sizing (Size X:Y), can also be managed from the CAM Editor - Drawing Modes page of the Preferences dialog. The size drop-down field lists previously used grid values, or simply enter new sizing directly, as required.
  3. The snap grid is used when the Object Snap mode is set to Grid. The object snapping mode can be changed on the CAMtastic panel, or on the CAM Editor - Drawing Modes page of the Preferences dialog. With the mode set to Grid, the cursor automatically snaps to the grid, positioning the reference point of the object being placed onto the nearest grid location.


Applied Parameters: Size=500Mil

Summary

This command is used to set the X (horizontal) and Y (vertical) step values - for the Snap Grid - simultaneously to 500mil. These values together define the Snap Grid for manual movement and placement in the current document.

Access

This command is accessed from the CAMtastic Editor, by:

  • Using the G keyboard shortcut, then choosing the 500 Mil command from the pop-up menu.
  • Choosing the 500 Mil entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for both the X Grid and Y Grid properties of the Snap Grid will be set to 500mil, and the grid will update accordingly in the workspace.

Tips

  1. The X and Y grid values can be changed as required, and independently for the snap grid, by editing the grid through the Enter Grid (1..1000mil) dialog, accessed by using the Ctrl+G keyboard shortcut.
  2. Display of the grid (On/Off), as well as grid sizing (Size X:Y), can also be managed from the CAM Editor - Drawing Modes page of the Preferences dialog. The size drop-down field lists previously used grid values, or simply enter new sizing directly, as required.
  3. The snap grid is used when the Object Snap mode is set to Grid. The object snapping mode can be changed on the CAMtastic panel, or on the CAM Editor - Drawing Modes page of the Preferences dialog. With the mode set to Grid, the cursor automatically snaps to the grid, positioning the reference point of the object being placed onto the nearest grid location.


Applied Parameters: Size=0.025MM

Summary

This command is used to set the X (horizontal) and Y (vertical) step values - for the Snap Grid - simultaneously to 0.025mm. These values together define the Snap Grid for manual movement and placement in the current document.

Access

This command is accessed from the CAMtastic Editor, by:

  • Using the G keyboard shortcut, then choosing the 0.025 mm command from the pop-up menu.
  • Choosing the 0.025 mm entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for both the X Grid and Y Grid properties of the Snap Grid will be set to 0.025mm, and the grid will update accordingly in the workspace.

Tips

  1. The X and Y grid values can be changed as required, and independently for the snap grid, by editing the grid through the Enter Grid (1..1000mil) dialog, accessed by using the Ctrl+G keyboard shortcut.
  2. Display of the grid (On/Off), as well as grid sizing (Size X:Y), can also be managed from the CAM Editor - Drawing Modes page of the Preferences dialog. The size drop-down field lists previously used grid values, or simply enter new sizing directly, as required.
  3. The snap grid is used when the Object Snap mode is set to Grid. The object snapping mode can be changed on the CAMtastic panel, or on the CAM Editor - Drawing Modes page of the Preferences dialog. With the mode set to Grid, the cursor automatically snaps to the grid, positioning the reference point of the object being placed onto the nearest grid location.


Applied Parameters: Size=0.100MM

Summary

This command is used to set the X (horizontal) and Y (vertical) step values - for the Snap Grid - simultaneously to 0.100mm. These values together define the Snap Grid for manual movement and placement in the current document.

Access

This command is accessed from the CAMtastic Editor, by:

  • Using the G keyboard shortcut, then choosing the 0.100 mm command from the pop-up menu.
  • Choosing the 0.100 mm entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for both the X Grid and Y Grid properties of the Snap Grid will be set to 0.100mm, and the grid will update accordingly in the workspace.

Tips

  1. The X and Y grid values can be changed as required, and independently for the snap grid, by editing the grid through the Enter Grid (1..1000mil) dialog, accessed by using the Ctrl+G keyboard shortcut.
  2. Display of the grid (On/Off), as well as grid sizing (Size X:Y), can also be managed from the CAM Editor - Drawing Modes page of the Preferences dialog. The size drop-down field lists previously used grid values, or simply enter new sizing directly, as required.
  3. The snap grid is used when the Object Snap mode is set to Grid. The object snapping mode can be changed on the CAMtastic panel, or on the CAM Editor - Drawing Modes page of the Preferences dialog. With the mode set to Grid, the cursor automatically snaps to the grid, positioning the reference point of the object being placed onto the nearest grid location.


Applied Parameters: Size=0.250MM

Summary

This command is used to set the X (horizontal) and Y (vertical) step values - for the Snap Grid - simultaneously to 0.250mm. These values together define the Snap Grid for manual movement and placement in the current document.

Access

This command is accessed from the CAMtastic Editor, by:

  • Using the G keyboard shortcut, then choosing the 0.250 mm command from the pop-up menu.
  • Choosing the 0.250 mm entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for both the X Grid and Y Grid properties of the Snap Grid will be set to 0.250mm, and the grid will update accordingly in the workspace.

Tips

  1. The X and Y grid values can be changed as required, and independently for the snap grid, by editing the grid through the Enter Grid (1..1000mil) dialog, accessed by using the Ctrl+G keyboard shortcut.
  2. Display of the grid (On/Off), as well as grid sizing (Size X:Y), can also be managed from the CAM Editor - Drawing Modes page of the Preferences dialog. The size drop-down field lists previously used grid values, or simply enter new sizing directly, as required.
  3. The snap grid is used when the Object Snap mode is set to Grid. The object snapping mode can be changed on the CAMtastic panel, or on the CAM Editor - Drawing Modes page of the Preferences dialog. With the mode set to Grid, the cursor automatically snaps to the grid, positioning the reference point of the object being placed onto the nearest grid location.


Applied Parameters: Size=0.500MM

Summary

This command is used to set the X (horizontal) and Y (vertical) step values - for the Snap Grid - simultaneously to 0.500mm. These values together define the Snap Grid for manual movement and placement in the current document.

Access

This command is accessed from the CAMtastic Editor, by:

  • Using the G keyboard shortcut, then choosing the 0.500 mm command from the pop-up menu.
  • Choosing the 0.500 mm entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for both the X Grid and Y Grid properties of the Snap Grid will be set to 0.500mm, and the grid will update accordingly in the workspace.

Tips

  1. The X and Y grid values can be changed as required, and independently for the snap grid, by editing the grid through the Enter Grid (1..1000mil) dialog, accessed by using the Ctrl+G keyboard shortcut.
  2. Display of the grid (On/Off), as well as grid sizing (Size X:Y), can also be managed from the CAM Editor - Drawing Modes page of the Preferences dialog. The size drop-down field lists previously used grid values, or simply enter new sizing directly, as required.
  3. The snap grid is used when the Object Snap mode is set to Grid. The object snapping mode can be changed on the CAMtastic panel, or on the CAM Editor - Drawing Modes page of the Preferences dialog. With the mode set to Grid, the cursor automatically snaps to the grid, positioning the reference point of the object being placed onto the nearest grid location.


Applied Parameters: Size=1.000MM

Summary

This command is used to set the X (horizontal) and Y (vertical) step values - for the Snap Grid - simultaneously to 1.000mm. These values together define the Snap Grid for manual movement and placement in the current document.

Access

This command is accessed from the CAMtastic Editor, by:

  • Using the G keyboard shortcut, then choosing the 1.000 mm command from the pop-up menu.
  • Choosing the 1.000 mm entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for both the X Grid and Y Grid properties of the Snap Grid will be set to 1.000mm, and the grid will update accordingly in the workspace.

Tips

  1. The X and Y grid values can be changed as required, and independently for the snap grid, by editing the grid through the Enter Grid (1..1000mil) dialog, accessed by using the Ctrl+G keyboard shortcut.
  2. Display of the grid (On/Off), as well as grid sizing (Size X:Y), can also be managed from the CAM Editor - Drawing Modes page of the Preferences dialog. The size drop-down field lists previously used grid values, or simply enter new sizing directly, as required.
  3. The snap grid is used when the Object Snap mode is set to Grid. The object snapping mode can be changed on the CAMtastic panel, or on the CAM Editor - Drawing Modes page of the Preferences dialog. With the mode set to Grid, the cursor automatically snaps to the grid, positioning the reference point of the object being placed onto the nearest grid location.


Applied Parameters: Size=2.500MM

Summary

This command is used to set the X (horizontal) and Y (vertical) step values - for the Snap Grid - simultaneously to 2.500mm. These values together define the Snap Grid for manual movement and placement in the current document.

Access

This command is accessed from the CAMtastic Editor, by:

  • Using the G keyboard shortcut, then choosing the 2.500 mm command from the pop-up menu.
  • Choosing the 2.500 mm entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for both the X Grid and Y Grid properties of the Snap Grid will be set to 2.500mm, and the grid will update accordingly in the workspace.

Tips

  1. The X and Y grid values can be changed as required, and independently for the snap grid, by editing the grid through the Enter Grid (1..1000mil) dialog, accessed by using the Ctrl+G keyboard shortcut.
  2. Display of the grid (On/Off), as well as grid sizing (Size X:Y), can also be managed from the CAM Editor - Drawing Modes page of the Preferences dialog. The size drop-down field lists previously used grid values, or simply enter new sizing directly, as required.
  3. The snap grid is used when the Object Snap mode is set to Grid. The object snapping mode can be changed on the CAMtastic panel, or on the CAM Editor - Drawing Modes page of the Preferences dialog. With the mode set to Grid, the cursor automatically snaps to the grid, positioning the reference point of the object being placed onto the nearest grid location.


Applied Parameters: Size=5.000MM

Summary

This command is used to set the X (horizontal) and Y (vertical) step values - for the Snap Grid - simultaneously to 5.000mm. These values together define the Snap Grid for manual movement and placement in the current document.

Access

This command is accessed from the CAMtastic Editor, by:

  • Using the G keyboard shortcut, then choosing the 5.000 mm command from the pop-up menu.
  • Choosing the 5.000 mm entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for both the X Grid and Y Grid properties of the Snap Grid will be set to 5.000mm, and the grid will update accordingly in the workspace.

Tips

  1. The X and Y grid values can be changed as required, and independently for the snap grid, by editing the grid through the Enter Grid (1..1000mil) dialog, accessed by using the Ctrl+G keyboard shortcut.
  2. Display of the grid (On/Off), as well as grid sizing (Size X:Y), can also be managed from the CAM Editor - Drawing Modes page of the Preferences dialog. The size drop-down field lists previously used grid values, or simply enter new sizing directly, as required.
  3. The snap grid is used when the Object Snap mode is set to Grid. The object snapping mode can be changed on the CAMtastic panel, or on the CAM Editor - Drawing Modes page of the Preferences dialog. With the mode set to Grid, the cursor automatically snaps to the grid, positioning the reference point of the object being placed onto the nearest grid location.


Applied Parameters: Size=7.500MM

Summary

This command is used to set the X (horizontal) and Y (vertical) step values - for the Snap Grid - simultaneously to 7.500mm. These values together define the Snap Grid for manual movement and placement in the current document.

Access

This command is accessed from the CAMtastic Editor, by:

  • Using the G keyboard shortcut, then choosing the 7.500 mm command from the pop-up menu.
  • Choosing the 7.500 mm entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for both the X Grid and Y Grid properties of the Snap Grid will be set to 7.500mm, and the grid will update accordingly in the workspace.

Tips

  1. The X and Y grid values can be changed as required, and independently for the snap grid, by editing the grid through the Enter Grid (1..1000mil) dialog, accessed by using the Ctrl+G keyboard shortcut.
  2. Display of the grid (On/Off), as well as grid sizing (Size X:Y), can also be managed from the CAM Editor - Drawing Modes page of the Preferences dialog. The size drop-down field lists previously used grid values, or simply enter new sizing directly, as required.
  3. The snap grid is used when the Object Snap mode is set to Grid. The object snapping mode can be changed on the CAMtastic panel, or on the CAM Editor - Drawing Modes page of the Preferences dialog. With the mode set to Grid, the cursor automatically snaps to the grid, positioning the reference point of the object being placed onto the nearest grid location.


Applied Parameters: None

Summary

This command is used to set the X (horizontal) and Y (vertical) step values - for the Snap Grid - simultaneously to a chosen value. These values together define the Snap Grid for manual movement and placement in the current document.

Access

This command is accessed from the CAMtastic Editor, by:

  • Using the Ctrl+G keyboard shortcut.
  • Using the G keyboard shortcut, then choosing the Set Snap Grid command from the pop-up menu.
  • Choosing the Set Snap Grid entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the Enter Grid (1..1000mil) dialog will appear. Enter the same, or different values to be used for the X Grid and Y Grid properties of the Snap Grid, and click OK - the grid will update accordingly in the workspace.

Tips

  1. Display of the grid (On/Off), as well as grid sizing (Size X:Y), can also be managed from the CAM Editor - Drawing Modes page of the Preferences dialog. The size drop-down field lists previously used grid values, or simply enter new sizing directly, as required.
  2. The snap grid is used when the Object Snap mode is set to Grid. The object snapping mode can be changed on the CAMtastic panel, or on the CAM Editor - Drawing Modes page of the Preferences dialog. With the mode set to Grid, the cursor automatically snaps to the grid, positioning the reference point of the object being placed onto the nearest grid location.

 

Обнаружили проблему в этом документе? Выделите область и нажмите Ctrl+Enter, чтобы оповестить нас.

Связаться с нами

Связаться с нашими Представительствами напрямую

Вы сообщаете о проблеме, связанной со следующим выделенным текстом
и/или изображением в активном документе:
Бесплатная пробная версия Altium Designer
Бесплатная пробная версия Altium Designer
Давайте приступим. Для начала, Вы или Ваше предприятие уже используете Altium Designer?

Если Вы хотите поговорить с представителем, пожалуйста, свяжитесь с местным офисом Altium.
Copyright © 2019 Altium Limited

В таком случае, для чего Вам необходима пробная лицензия?

Если Вы хотите поговорить с представителем, пожалуйста, свяжитесь с местным офисом Altium.
Copyright © 2019 Altium Limited

Вам для этого не нужна пробная лицензия.

Нажмите кнопку ниже, чтобы загрузить установщик самой новой версии Altium Designer

Загрузить установщик Altium Designer

Если Вы хотите поговорить с представителем, пожалуйста, свяжитесь с местным офисом Altium.
Copyright © 2019 Altium Limited

Пожалуйста, заполните форму ниже, чтобы получить ценовое предложение.

Нажимая [Получить бесплатнную пробную версию], Вы соглашаетесь с нашей Политикой конфиденциальности. Вам могут приходить сообщения от компании Altium, и Вы можете изменить настройки уведомлений в любой момент.

Если Ваша подписка Altium активна, у Вас нет необходимости в пробной лицензии.

Если у Вас нет активной подписки Altium, пожалуйста, заполните форму ниже, чтобы получить пробную версию.

Нажимая [Получить бесплатнную пробную версию], Вы соглашаетесь с нашей Политикой конфиденциальности. Вам могут приходить сообщения от компании Altium, и Вы можете изменить настройки уведомлений в любой момент.

Для чего Вы хотите попробовать Altium Designer?

Если Вы хотите поговорить с представителем, пожалуйста, свяжитесь с местным офисом Altium.
Copyright © 2019 Altium Limited

Вы нашли нужное место! Пожалуйста, заполните форму ниже, чтобы начать использование пробной версии.

Нажимая [Получить бесплатнную пробную версию], Вы соглашаетесь с нашей Политикой конфиденциальности. Вам могут приходить сообщения от компании Altium, и Вы можете изменить настройки уведомлений в любой момент.

Great News!

Valid students can get their very own 6-month Altium Designer Student License for FREE! Just fill out the form below to request your Student License today.

Нажимая [Получить бесплатнную пробную версию], Вы соглашаетесь с нашей Политикой конфиденциальности. Вам могут приходить сообщения от компании Altium, и Вы можете изменить настройки уведомлений в любой момент.

Вы можете загрузить бесплатную лицензию средства просмотра Altium Designer Viewer сроком действия 6 месяцев.

Пожалуйста, заполните форму ниже, чтобы запросить эту лицензию.

Нажимая [Получить бесплатнную пробную версию], Вы соглашаетесь с нашей Политикой конфиденциальности. Вам могут приходить сообщения от компании Altium, и Вы можете изменить настройки уведомлений в любой момент.

Замечательно! Создавать новое - отличное занятие. У нас есть превосходная программа для Вас.

Upverter - бесплатная платформа, разработанная специально для любителей проектирования.

Нажмите здесь, чтобы попробовать!

Если Вы хотите поговорить с представителем, пожалуйста, свяжитесь с местным офисом Altium.
Copyright © 2019 Altium Limited

Вы можете загрузить бесплатную лицензию средства просмотра Altium Designer Viewer сроком действия 6 месяцев.

Пожалуйста, заполните форму ниже, чтобы запросить эту лицензию.

Нажимая [Получить бесплатнную пробную версию], Вы соглашаетесь с нашей Политикой конфиденциальности. Вам могут приходить сообщения от компании Altium, и Вы можете изменить настройки уведомлений в любой момент.