Altium NEXUS Documentation

Status message

Данная страница доступна на русском языке для версии Altium Designer 2.0: перейти


Created: 18.03.2022 | Updated: 15.06.2022
На этой странице документации упоминается Altium NEXUS/NEXUS Client (часть развернутого решения NEXUS), поддержка которого прекращена. Все ваши потребности в проектировании печатных плат, управлении данными и совместной работе теперь могут быть реализованы с помощью Altium Designer (с подпиской Altium Designer Enterprise) и подключенного рабочего пространства Altium 365 Workspace. Посетите страницу часто задаваемых вопросов (FAQs) для получения дополнительной информации.

Parent page: Working with Panels


Modes of the PCB panel


The PCB panel allows you to browse the current PCB design using a range of filter modes to determine which object types or design elements are listed, highlighted or selected. The panel also has editing modes for specific object types or design elements that provide dedicated controls for editing procedures. You also can access the properties for any element listed in the panel.

Panel Access

When the PCB editor is active, click the Panels button at the bottom-right corner of the design space then select PCB from the menu. Alternatively, you can access the panel through the View » Panels » PCB command from the main menus.

Panel Modes

The PCB panel's functionality can change, depending on which mode is used. The different panel modes can be accessed and selected by clicking on the drop-down at the top of the panel.

While the middle sections change between the various modes of the PCB panel, the top and bottom portions of the panel remain the same.

The various panel mode options available.
The various panel mode options available.

Setting the Visual Filtering

The visual result of the applied filtering on the document in the design editor window is determined by a series of highlighting controls toward the top of the panel. The effect that is imposed in the editor view can be set to Normal, Mask or Dim; in practice, Mask has the most obvious highlighting effect. The filtering feature is very effective in a busy design space, and can also be used in the PCB Rules and Violations panel and the PCB Filter panel.

The Normal/Mask/Dim drop-down list provides options for visibly contrasting filtered and unfiltered objects within the design editor window.

Select the type of visual filtering applied using the masking mode drop-down list.
Select the type of visual filtering applied using the masking mode drop-down list.

The visual highlighting effect for each masking mode:

  • Normal - filtered objects are visible in the design space and the appearance of unfiltered objects remains unchanged.
  • Mask - filtered objects are highlighted in the design space with all other objects made monochrome.
  • Dim - filtered objects are highlighted in the design space with all other objects retaining their colors but shaded.

Confirm any changed settings by clicking the Apply button. Click the Clear button or use the Shift+C shortcut to return to the default settings.

The amount that the display is faded is controlled by the Dim and Mask slider controls, which are in the Mask and Dim Settings section of the View Options tab of the View Configuration panel. Press the L shortcut to display the panel.

Filter Options

The panel's three checkboxes apply these filter actions:

  • Select - when enabled, the filtered objects will be selected in the design space.
  • Zoom - when enabled (default), the filtered objects will be zoomed and centered (where possible) in the design editor window. Use the Zoom Level button to adjust the zoom factor that will be used to close-in on filtered objects.
  • Clear Existing - when enabled (default), any existing filter will be cleared before applying a new one. Disabling this option allows you to extend an existing filter, essentially refining the filter further by applying a new filter in addition to the existing one.

Any combination of these options can be enabled. For example, you might want to have all filtered objects zoomed, centered and selected in the design editor window while applying masking to take away the clutter of other design objects.

Click the Clear button to disable the currently-applied filter. All objects in the design space will become fully visible and available for selection/editing. If you want to reapply the filter, click the Apply button.

Panel Mini-viewer

The bottom section of the PCB panel provides a mini-viewer for the current document with an image of the PCB board central to its window. A white viewing box is imposed on the image to show the area currently displayed in the design editor window. As the editor display automatically pans and zooms in response to the PCB panel filter selections, the box moves and expands accordingly to indicate the board viewing area.

As you manually pan around the document in the design editor window - using the editor's horizontal and vertical scroll bars or the right-click panning hand - the viewing box in the panel will also move accordingly. Conversely, if you click inside the viewing box and drag it around the board image, the document in the design editor window will pan accordingly and at the current zoom level.

As you zoom in or out in the design editor window, the viewing box will be resized accordingly in the panel. Conversely, resizing the viewing box in the panel by clicking and dragging on any of its vertices will cause the zoom level to change in the design editor window. The smaller the size of the viewing box, the more the actual document has been zoomed-in.

Обнаружили проблему в этом документе? Выделите область и нажмите Ctrl+Enter, чтобы оповестить нас.

Связаться с нами

Связаться с нашими Представительствами напрямую

We're sorry to hear the article wasn't helpful to you.
Could you take a moment to tell us why?
200 characters remaining
Вы сообщаете о проблеме, связанной со следующим выделенным текстом
и/или изображением в активном документе: