Altium Designer Documentation

AdvancedDiffPairRoute

Modified by Susan Riege on Jul 16, 2018

Parent page: PCB Commands

The following pre-packaged resource, derived from this base command, is available:


Applied Parameters: None

Summary

This command is used to place differential pair track objects onto the current document and is useful for quickly routing connections manually. Differential pair routing is a design technique employed to create a balanced transmission system able to carry differential (equal and opposite) signals across a printed circuit board. Typically this differential routing will interface to an external differential transmission system, such as a connector and cable.

A differential signaling system is one where a signal is transmitted down a pair of tightly coupled carriers, one of these carrying the signal, the other carrying an equal but opposite image of the signal. Differential signaling was developed to cater for situations where the logic reference ground of the signal source could not be well connected to the logic reference ground of the load. Differential signaling is inherently immune to common mode electrical noise, the most common interference artifact present in an electronic product. Another major advantage of differential signaling is that it minimizes electromagnetic interference (EMI) generated from the signal pair.

Differential pairs need to be defined first either through the schematic design (using _P and _N suffixes on applicable nets), or manually via the PCB panel (configured in its Differential Pairs Editor mode). You also need to have defined applicable rules prior to using this command. These are: Routing Width, Differential Pairs Routing, and Electrical Clearance.

Access

This command can be accessed from the PCB Editor by:

  • Choosing the Route » Interactive Differential Pair Routing command from the main menus.
  • Locating and using the Interactive Differential Pair Routing command () on the Active Bar.
If the command has been recently used from the Active Bar, it will become the active/visible button. Where other commands are available, this is indicated by a triangle at the bottom-right corner of the button. Click and hold on the active button to access a menu of all associated commands for that grouping.
  • Clicking the  button on the Wiring toolbar.

Use

Differential pairs are routed as a pair - that is, you route two nets simultaneously. After launching the command, you will be prompted to select one of the nets in the pair. Click on either to start routing. It doesn't matter if the positive or negative trace in a pair is selected as the system will automatically select the other trace too.

As you route the differential pair, the standard conflict resolutions modes are available, including Walkaround Obstacles, Push Obstacles, Hug and Push Obstacles, Ignore obstacles, and Stop at First Obstacle. Use Shift+R to cycle through the modes.

Use the + and - keys on the numeric keypad to switch routing layers.

Press Shift+F1 to display all of the available shortcuts for commands available to you while in interactive differential pair routing mode. Shortcuts are also reflected in the Properties panel, which presents controls and options available while using the interactive differential pair routing tool.

Placement Modes

While placing track segments there are 4 available corner modes, all of which also have corner direction sub-modes. During placement:

  • Press Shift+Spacebar to cycle through the available corner modes: 45 degree, 45 degree with arc, 90 degree, 90 degree with arc.
  • Press Spacebar to toggle between the two corner direction sub-modes.
  • When in either of the arc corner modes, hold the  or  keys to shrink or grow the arc. Hold the Shift key as you press to accelerate arc resizing.
  • Press the Backspace key to remove the last vertex.

Loop Removal

Altium Designer provides support for Loop Removal when interactively routing your differential pairs. As you route there will be many instances where you need to change some of the existing routing. Rather than attempting to change the existing routing using a drafting type approach of clicking and dragging track segments, you re-route. To do this, launch the Interactive Differential Pair Routing command, click on the existing routing to start, and then route the new path, coming back to meet the existing routing. This will create a loop with the old path and the new path - no need to worry though, as soon as you right-click or press Esc to terminate the route, the redundant segments are automatically removed, including any redundant vias.

This feature is employed by enabling the Automatically Remove Loops option - either from within the Properties panel (while in interactive differential pair routing mode), or on the PCB Editor - Interactive Routing page of the Preferences dialog. To toggle this feature on or off while routing, use the Shift+D keyboard shortcut.

Displaying Clearance Boundaries

As you route, it can be extremely beneficial to have an indication of just how much space you really do have available to you. Altium Designer provides this very aid, through dynamic display of clearance boundaries. As you interactively route, the no-go clearance area defined by the existing objects + the applicable clearance rule is displayed as shaded polygons. By default, all clearance boundaries are displayed, but you can opt to reduce the clearance display area - only viewing b oundaries that fall within a localized viewing circle.

The clearance around existing workspace objects is displayed dynamically, as you route. Use the Ctrl+W shortcut to enable/disable during routing.

This feature is employed by enabling the Display Clearance Boundaries option - either from within the Properties panel (while in interactive differential pair routing mode), or on the PCB Editor - Interactive Routing page of the Preferences dialog. To toggle this feature on or off while routing, use the Ctrl+W keyboard shortcut. To show clearance boundaries only with a localized area, ensure to enable the Reduce Clearance Display Area sub-option.
The display of clearance boundaries is available in all routing modes except Ignore Obstacles.

Tips

  1. Interactive routing preferences can be defined on the PCB Editor - Interactive Routing page of the Preferences dialog. In addition, and while routing, applicable options can be accessed through the Properties panel. While many controls are accessed through a corresponding keyboard shortcut (indicated in the panel), you can also pause routing in order to interact with the panel (or other area of the software) directly. To pause routing, simply press the Tab key. To resume, click the pause symbol that appears over the workspace, or press Esc.
  2. The required rules for differential pair routing can be defined manually, or can be defined through the use of the Differential Pair Rule Wizard - available from the PCB panel, when configured in Differential Pairs Editor mode.
  3. The lengths of the differential pairs can be tuned accurately using the Interactive Diff Pair Length Tuning command (accessed from the main Route menu). When using this feature you have full on-the-fly control over target length and tolerance, and have various options to increase differential pair net lengths by adding variable amplitude wave patterns to the net pairs.
  4. For a high-level overview on routing differential pair nets in Altium Designer, see Differential Pair Routing.

 

Found an issue with this document? Highlight the area, then use Ctrl+Enter to report it.

Contact Us

Contact our corporate or local offices directly.

We're sorry to hear the article wasn't helpful to you.
Could you take a moment to tell us why?
You are reporting an issue with the following selected text
and/or image within the active document:
ALTIUM DESIGNER FREE TRIAL
Altium Designer Free Trial
Let’s get started. First off, are you or your organization already using Altium Designer?

If would like to speak with a representative, please contact your local Altium office.
Copyright © 2019 Altium Limited

In that case, why do you need an evaluation license?

If would like to speak with a representative, please contact your local Altium office.
Copyright © 2019 Altium Limited

Got it. You actually don’t need an evaluation license for that.

Click the button below to download the latest Altium Designer installer.

Download Altium Designer Installer

If would like to speak with a representative, please contact your local Altium office.
Copyright © 2019 Altium Limited

Please fill out the form below to get a quote for a new seat of Altium Designer.

By clicking “Get Your Free Trial”, you are agreeing to our Privacy Policy.
You may receive communications from Altium and can change your notification preferences at any time.

If you are on Altium Subscription, you don’t need an evaluation license.

If you are not an active Altium Subscription member, please fill out the form below to get your free trial.

By clicking “Get Your Free Trial”, you are agreeing to our Privacy Policy.
You may receive communications from Altium and can change your notification preferences at any time.

Why are you looking to evaluate Altium Designer?

If would like to speak with a representative, please contact your local Altium office.
Copyright © 2019 Altium Limited

You came to the right place! Please fill out the form below to get your free trial started.

By clicking “Get Your Free Trial”, you are agreeing to our Privacy Policy.
You may receive communications from Altium and can change your notification preferences at any time.

Great News!

Valid students can get their very own 6-month Altium Designer Student License for FREE! Just fill out the form below to request your Student License today.

By clicking “Get Your Free Trial”, you are agreeing to our Privacy Policy.
You may receive communications from Altium and can change your notification preferences at any time.

Got it. You can download a free Altium Designer Viewer license which is valid for a 6 months.

Please fill out the form below to request one.

By clicking “Get Your Free Trial”, you are agreeing to our Privacy Policy.
You may receive communications from Altium and can change your notification preferences at any time.

That’s great! Making things is awesome. We have the perfect program for you.

Upverter is a free community-driven platform designed specifically to meet the needs of makers like you.

Click here to give it a try!

If would like to speak with a representative, please contact your local Altium office.
Copyright © 2019 Altium Limited

Got it. You can download a free Altium Designer Viewer license which is valid for a 6 months.

Please fill out the form below to request one.

By clicking “Get Your Free Trial”, you are agreeing to our Privacy Policy.
You may receive communications from Altium and can change your notification preferences at any time.