Altium NEXUS Documentation

SnapGrid

Modified by Jason Howie on Apr 11, 2017

Parent page: CAMtastic Commands

The following pre-packaged resources, derived from this base command, are available:


Applied Parameters: Size=1Mil

Summary

This command is used to set the X (horizontal) and Y (vertical) step values - for the Snap Grid - simultaneously to 1mil. These values together define the Snap Grid for manual movement and placement in the current document.

Access

This command is accessed from the CAMtastic Editor, by:

  • Using the G keyboard shortcut, then choosing the 1 Mil command from the pop-up menu.
  • Choosing the 1 Mil entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for both the X Grid and Y Grid properties of the Snap Grid will be set to 1mil, and the grid will update accordingly in the workspace.

Tips

  1. The X and Y grid values can be changed as required, and independently for the snap grid, by editing the grid through the Enter Grid (1..1000mil) dialog, accessed by using the Ctrl+G keyboard shortcut.
  2. Display of the grid (On/Off), as well as grid sizing (Size X:Y), can also be managed from the CAM Editor - Drawing Modes page of the Preferences dialog. The size drop-down field lists previously used grid values, or simply enter new sizing directly, as required.
  3. The snap grid is used when the Object Snap mode is set to Grid. The object snapping mode can be changed on the CAMtastic panel, or on the CAM Editor - Drawing Modes page of the Preferences dialog. With the mode set to Grid, the cursor automatically snaps to the grid, positioning the reference point of the object being placed onto the nearest grid location.


Applied Parameters: Size=5Mil

Summary

This command is used to set the X (horizontal) and Y (vertical) step values - for the Snap Grid - simultaneously to 5mil. These values together define the Snap Grid for manual movement and placement in the current document.

Access

This command is accessed from the CAMtastic Editor, by:

  • Using the G keyboard shortcut, then choosing the 5 Mil command from the pop-up menu.
  • Choosing the 5 Mil entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for both the X Grid and Y Grid properties of the Snap Grid will be set to 5mil, and the grid will update accordingly in the workspace.

Tips

  1. The X and Y grid values can be changed as required, and independently for the snap grid, by editing the grid through the Enter Grid (1..1000mil) dialog, accessed by using the Ctrl+G keyboard shortcut.
  2. Display of the grid (On/Off), as well as grid sizing (Size X:Y), can also be managed from the CAM Editor - Drawing Modes page of the Preferences dialog. The size drop-down field lists previously used grid values, or simply enter new sizing directly, as required.
  3. The snap grid is used when the Object Snap mode is set to Grid. The object snapping mode can be changed on the CAMtastic panel, or on the CAM Editor - Drawing Modes page of the Preferences dialog. With the mode set to Grid, the cursor automatically snaps to the grid, positioning the reference point of the object being placed onto the nearest grid location.


Applied Parameters: Size=10Mil

Summary

This command is used to set the X (horizontal) and Y (vertical) step values - for the Snap Grid - simultaneously to 10mil. These values together define the Snap Grid for manual movement and placement in the current document.

Access

This command is accessed from the CAMtastic Editor, by:

  • Using the G keyboard shortcut, then choosing the 10 Mil command from the pop-up menu.
  • Choosing the 10 Mil entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for both the X Grid and Y Grid properties of the Snap Grid will be set to 10mil, and the grid will update accordingly in the workspace.

Tips

  1. The X and Y grid values can be changed as required, and independently for the snap grid, by editing the grid through the Enter Grid (1..1000mil) dialog, accessed by using the Ctrl+G keyboard shortcut.
  2. Display of the grid (On/Off), as well as grid sizing (Size X:Y), can also be managed from the CAM Editor - Drawing Modes page of the Preferences dialog. The size drop-down field lists previously used grid values, or simply enter new sizing directly, as required.
  3. The snap grid is used when the Object Snap mode is set to Grid. The object snapping mode can be changed on the CAMtastic panel, or on the CAM Editor - Drawing Modes page of the Preferences dialog. With the mode set to Grid, the cursor automatically snaps to the grid, positioning the reference point of the object being placed onto the nearest grid location.


Applied Parameters: Size=20Mil

Summary

This command is used to set the X (horizontal) and Y (vertical) step values - for the Snap Grid - simultaneously to 20mil. These values together define the Snap Grid for manual movement and placement in the current document.

Access

This command is accessed from the CAMtastic Editor, by:

  • Using the G keyboard shortcut, then choosing the 20 Mil command from the pop-up menu.
  • Choosing the 20 Mil entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for both the X Grid and Y Grid properties of the Snap Grid will be set to 20mil, and the grid will update accordingly in the workspace.

Tips

  1. The X and Y grid values can be changed as required, and independently for the snap grid, by editing the grid through the Enter Grid (1..1000mil) dialog, accessed by using the Ctrl+G keyboard shortcut.
  2. Display of the grid (On/Off), as well as grid sizing (Size X:Y), can also be managed from the CAM Editor - Drawing Modes page of the Preferences dialog. The size drop-down field lists previously used grid values, or simply enter new sizing directly, as required.
  3. The snap grid is used when the Object Snap mode is set to Grid. The object snapping mode can be changed on the CAMtastic panel, or on the CAM Editor - Drawing Modes page of the Preferences dialog. With the mode set to Grid, the cursor automatically snaps to the grid, positioning the reference point of the object being placed onto the nearest grid location.


Applied Parameters: Size=25Mil

Summary

This command is used to set the X (horizontal) and Y (vertical) step values - for the Snap Grid - simultaneously to 25mil. These values together define the Snap Grid for manual movement and placement in the current document.

Access

This command is accessed from the CAMtastic Editor, by:

  • Using the G keyboard shortcut, then choosing the 25 Mil command from the pop-up menu.
  • Choosing the 25 Mil entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for both the X Grid and Y Grid properties of the Snap Grid will be set to 25mil, and the grid will update accordingly in the workspace.

Tips

  1. The X and Y grid values can be changed as required, and independently for the snap grid, by editing the grid through the Enter Grid (1..1000mil) dialog, accessed by using the Ctrl+G keyboard shortcut.
  2. Display of the grid (On/Off), as well as grid sizing (Size X:Y), can also be managed from the CAM Editor - Drawing Modes page of the Preferences dialog. The size drop-down field lists previously used grid values, or simply enter new sizing directly, as required.
  3. The snap grid is used when the Object Snap mode is set to Grid. The object snapping mode can be changed on the CAMtastic panel, or on the CAM Editor - Drawing Modes page of the Preferences dialog. With the mode set to Grid, the cursor automatically snaps to the grid, positioning the reference point of the object being placed onto the nearest grid location.


Applied Parameters: Size=50Mil

Summary

This command is used to set the X (horizontal) and Y (vertical) step values - for the Snap Grid - simultaneously to 50mil. These values together define the Snap Grid for manual movement and placement in the current document.

Access

This command is accessed from the CAMtastic Editor, by:

  • Using the G keyboard shortcut, then choosing the 50 Mil command from the pop-up menu.
  • Choosing the 50 Mil entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for both the X Grid and Y Grid properties of the Snap Grid will be set to 50mil, and the grid will update accordingly in the workspace.

Tips

  1. The X and Y grid values can be changed as required, and independently for the snap grid, by editing the grid through the Enter Grid (1..1000mil) dialog, accessed by using the Ctrl+G keyboard shortcut.
  2. Display of the grid (On/Off), as well as grid sizing (Size X:Y), can also be managed from the CAM Editor - Drawing Modes page of the Preferences dialog. The size drop-down field lists previously used grid values, or simply enter new sizing directly, as required.
  3. The snap grid is used when the Object Snap mode is set to Grid. The object snapping mode can be changed on the CAMtastic panel, or on the CAM Editor - Drawing Modes page of the Preferences dialog. With the mode set to Grid, the cursor automatically snaps to the grid, positioning the reference point of the object being placed onto the nearest grid location.


Applied Parameters: Size=100Mil

Summary

This command is used to set the X (horizontal) and Y (vertical) step values - for the Snap Grid - simultaneously to 100mil. These values together define the Snap Grid for manual movement and placement in the current document.

Access

This command is accessed from the CAMtastic Editor, by:

  • Using the G keyboard shortcut, then choosing the 100 Mil command from the pop-up menu.
  • Choosing the 100 Mil entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for both the X Grid and Y Grid properties of the Snap Grid will be set to 100mil, and the grid will update accordingly in the workspace.

Tips

  1. The X and Y grid values can be changed as required, and independently for the snap grid, by editing the grid through the Enter Grid (1..1000mil) dialog, accessed by using the Ctrl+G keyboard shortcut.
  2. Display of the grid (On/Off), as well as grid sizing (Size X:Y), can also be managed from the CAM Editor - Drawing Modes page of the Preferences dialog. The size drop-down field lists previously used grid values, or simply enter new sizing directly, as required.
  3. The snap grid is used when the Object Snap mode is set to Grid. The object snapping mode can be changed on the CAMtastic panel, or on the CAM Editor - Drawing Modes page of the Preferences dialog. With the mode set to Grid, the cursor automatically snaps to the grid, positioning the reference point of the object being placed onto the nearest grid location.


Applied Parameters: Size=200Mil

Summary

This command is used to set the X (horizontal) and Y (vertical) step values - for the Snap Grid - simultaneously to 200mil. These values together define the Snap Grid for manual movement and placement in the current document.

Access

This command is accessed from the CAMtastic Editor, by:

  • Using the G keyboard shortcut, then choosing the 200 Mil command from the pop-up menu.
  • Choosing the 200 Mil entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for both the X Grid and Y Grid properties of the Snap Grid will be set to 200mil, and the grid will update accordingly in the workspace.

Tips

  1. The X and Y grid values can be changed as required, and independently for the snap grid, by editing the grid through the Enter Grid (1..1000mil) dialog, accessed by using the Ctrl+G keyboard shortcut.
  2. Display of the grid (On/Off), as well as grid sizing (Size X:Y), can also be managed from the CAM Editor - Drawing Modes page of the Preferences dialog. The size drop-down field lists previously used grid values, or simply enter new sizing directly, as required.
  3. The snap grid is used when the Object Snap mode is set to Grid. The object snapping mode can be changed on the CAMtastic panel, or on the CAM Editor - Drawing Modes page of the Preferences dialog. With the mode set to Grid, the cursor automatically snaps to the grid, positioning the reference point of the object being placed onto the nearest grid location.


Applied Parameters: Size=500Mil

Summary

This command is used to set the X (horizontal) and Y (vertical) step values - for the Snap Grid - simultaneously to 500mil. These values together define the Snap Grid for manual movement and placement in the current document.

Access

This command is accessed from the CAMtastic Editor, by:

  • Using the G keyboard shortcut, then choosing the 500 Mil command from the pop-up menu.
  • Choosing the 500 Mil entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for both the X Grid and Y Grid properties of the Snap Grid will be set to 500mil, and the grid will update accordingly in the workspace.

Tips

  1. The X and Y grid values can be changed as required, and independently for the snap grid, by editing the grid through the Enter Grid (1..1000mil) dialog, accessed by using the Ctrl+G keyboard shortcut.
  2. Display of the grid (On/Off), as well as grid sizing (Size X:Y), can also be managed from the CAM Editor - Drawing Modes page of the Preferences dialog. The size drop-down field lists previously used grid values, or simply enter new sizing directly, as required.
  3. The snap grid is used when the Object Snap mode is set to Grid. The object snapping mode can be changed on the CAMtastic panel, or on the CAM Editor - Drawing Modes page of the Preferences dialog. With the mode set to Grid, the cursor automatically snaps to the grid, positioning the reference point of the object being placed onto the nearest grid location.


Applied Parameters: Size=0.025MM

Summary

This command is used to set the X (horizontal) and Y (vertical) step values - for the Snap Grid - simultaneously to 0.025mm. These values together define the Snap Grid for manual movement and placement in the current document.

Access

This command is accessed from the CAMtastic Editor, by:

  • Using the G keyboard shortcut, then choosing the 0.025 mm command from the pop-up menu.
  • Choosing the 0.025 mm entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for both the X Grid and Y Grid properties of the Snap Grid will be set to 0.025mm, and the grid will update accordingly in the workspace.

Tips

  1. The X and Y grid values can be changed as required, and independently for the snap grid, by editing the grid through the Enter Grid (1..1000mil) dialog, accessed by using the Ctrl+G keyboard shortcut.
  2. Display of the grid (On/Off), as well as grid sizing (Size X:Y), can also be managed from the CAM Editor - Drawing Modes page of the Preferences dialog. The size drop-down field lists previously used grid values, or simply enter new sizing directly, as required.
  3. The snap grid is used when the Object Snap mode is set to Grid. The object snapping mode can be changed on the CAMtastic panel, or on the CAM Editor - Drawing Modes page of the Preferences dialog. With the mode set to Grid, the cursor automatically snaps to the grid, positioning the reference point of the object being placed onto the nearest grid location.


Applied Parameters: Size=0.100MM

Summary

This command is used to set the X (horizontal) and Y (vertical) step values - for the Snap Grid - simultaneously to 0.100mm. These values together define the Snap Grid for manual movement and placement in the current document.

Access

This command is accessed from the CAMtastic Editor, by:

  • Using the G keyboard shortcut, then choosing the 0.100 mm command from the pop-up menu.
  • Choosing the 0.100 mm entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for both the X Grid and Y Grid properties of the Snap Grid will be set to 0.100mm, and the grid will update accordingly in the workspace.

Tips

  1. The X and Y grid values can be changed as required, and independently for the snap grid, by editing the grid through the Enter Grid (1..1000mil) dialog, accessed by using the Ctrl+G keyboard shortcut.
  2. Display of the grid (On/Off), as well as grid sizing (Size X:Y), can also be managed from the CAM Editor - Drawing Modes page of the Preferences dialog. The size drop-down field lists previously used grid values, or simply enter new sizing directly, as required.
  3. The snap grid is used when the Object Snap mode is set to Grid. The object snapping mode can be changed on the CAMtastic panel, or on the CAM Editor - Drawing Modes page of the Preferences dialog. With the mode set to Grid, the cursor automatically snaps to the grid, positioning the reference point of the object being placed onto the nearest grid location.


Applied Parameters: Size=0.250MM

Summary

This command is used to set the X (horizontal) and Y (vertical) step values - for the Snap Grid - simultaneously to 0.250mm. These values together define the Snap Grid for manual movement and placement in the current document.

Access

This command is accessed from the CAMtastic Editor, by:

  • Using the G keyboard shortcut, then choosing the 0.250 mm command from the pop-up menu.
  • Choosing the 0.250 mm entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for both the X Grid and Y Grid properties of the Snap Grid will be set to 0.250mm, and the grid will update accordingly in the workspace.

Tips

  1. The X and Y grid values can be changed as required, and independently for the snap grid, by editing the grid through the Enter Grid (1..1000mil) dialog, accessed by using the Ctrl+G keyboard shortcut.
  2. Display of the grid (On/Off), as well as grid sizing (Size X:Y), can also be managed from the CAM Editor - Drawing Modes page of the Preferences dialog. The size drop-down field lists previously used grid values, or simply enter new sizing directly, as required.
  3. The snap grid is used when the Object Snap mode is set to Grid. The object snapping mode can be changed on the CAMtastic panel, or on the CAM Editor - Drawing Modes page of the Preferences dialog. With the mode set to Grid, the cursor automatically snaps to the grid, positioning the reference point of the object being placed onto the nearest grid location.


Applied Parameters: Size=0.500MM

Summary

This command is used to set the X (horizontal) and Y (vertical) step values - for the Snap Grid - simultaneously to 0.500mm. These values together define the Snap Grid for manual movement and placement in the current document.

Access

This command is accessed from the CAMtastic Editor, by:

  • Using the G keyboard shortcut, then choosing the 0.500 mm command from the pop-up menu.
  • Choosing the 0.500 mm entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for both the X Grid and Y Grid properties of the Snap Grid will be set to 0.500mm, and the grid will update accordingly in the workspace.

Tips

  1. The X and Y grid values can be changed as required, and independently for the snap grid, by editing the grid through the Enter Grid (1..1000mil) dialog, accessed by using the Ctrl+G keyboard shortcut.
  2. Display of the grid (On/Off), as well as grid sizing (Size X:Y), can also be managed from the CAM Editor - Drawing Modes page of the Preferences dialog. The size drop-down field lists previously used grid values, or simply enter new sizing directly, as required.
  3. The snap grid is used when the Object Snap mode is set to Grid. The object snapping mode can be changed on the CAMtastic panel, or on the CAM Editor - Drawing Modes page of the Preferences dialog. With the mode set to Grid, the cursor automatically snaps to the grid, positioning the reference point of the object being placed onto the nearest grid location.


Applied Parameters: Size=1.000MM

Summary

This command is used to set the X (horizontal) and Y (vertical) step values - for the Snap Grid - simultaneously to 1.000mm. These values together define the Snap Grid for manual movement and placement in the current document.

Access

This command is accessed from the CAMtastic Editor, by:

  • Using the G keyboard shortcut, then choosing the 1.000 mm command from the pop-up menu.
  • Choosing the 1.000 mm entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for both the X Grid and Y Grid properties of the Snap Grid will be set to 1.000mm, and the grid will update accordingly in the workspace.

Tips

  1. The X and Y grid values can be changed as required, and independently for the snap grid, by editing the grid through the Enter Grid (1..1000mil) dialog, accessed by using the Ctrl+G keyboard shortcut.
  2. Display of the grid (On/Off), as well as grid sizing (Size X:Y), can also be managed from the CAM Editor - Drawing Modes page of the Preferences dialog. The size drop-down field lists previously used grid values, or simply enter new sizing directly, as required.
  3. The snap grid is used when the Object Snap mode is set to Grid. The object snapping mode can be changed on the CAMtastic panel, or on the CAM Editor - Drawing Modes page of the Preferences dialog. With the mode set to Grid, the cursor automatically snaps to the grid, positioning the reference point of the object being placed onto the nearest grid location.


Applied Parameters: Size=2.500MM

Summary

This command is used to set the X (horizontal) and Y (vertical) step values - for the Snap Grid - simultaneously to 2.500mm. These values together define the Snap Grid for manual movement and placement in the current document.

Access

This command is accessed from the CAMtastic Editor, by:

  • Using the G keyboard shortcut, then choosing the 2.500 mm command from the pop-up menu.
  • Choosing the 2.500 mm entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for both the X Grid and Y Grid properties of the Snap Grid will be set to 2.500mm, and the grid will update accordingly in the workspace.

Tips

  1. The X and Y grid values can be changed as required, and independently for the snap grid, by editing the grid through the Enter Grid (1..1000mil) dialog, accessed by using the Ctrl+G keyboard shortcut.
  2. Display of the grid (On/Off), as well as grid sizing (Size X:Y), can also be managed from the CAM Editor - Drawing Modes page of the Preferences dialog. The size drop-down field lists previously used grid values, or simply enter new sizing directly, as required.
  3. The snap grid is used when the Object Snap mode is set to Grid. The object snapping mode can be changed on the CAMtastic panel, or on the CAM Editor - Drawing Modes page of the Preferences dialog. With the mode set to Grid, the cursor automatically snaps to the grid, positioning the reference point of the object being placed onto the nearest grid location.


Applied Parameters: Size=5.000MM

Summary

This command is used to set the X (horizontal) and Y (vertical) step values - for the Snap Grid - simultaneously to 5.000mm. These values together define the Snap Grid for manual movement and placement in the current document.

Access

This command is accessed from the CAMtastic Editor, by:

  • Using the G keyboard shortcut, then choosing the 5.000 mm command from the pop-up menu.
  • Choosing the 5.000 mm entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for both the X Grid and Y Grid properties of the Snap Grid will be set to 5.000mm, and the grid will update accordingly in the workspace.

Tips

  1. The X and Y grid values can be changed as required, and independently for the snap grid, by editing the grid through the Enter Grid (1..1000mil) dialog, accessed by using the Ctrl+G keyboard shortcut.
  2. Display of the grid (On/Off), as well as grid sizing (Size X:Y), can also be managed from the CAM Editor - Drawing Modes page of the Preferences dialog. The size drop-down field lists previously used grid values, or simply enter new sizing directly, as required.
  3. The snap grid is used when the Object Snap mode is set to Grid. The object snapping mode can be changed on the CAMtastic panel, or on the CAM Editor - Drawing Modes page of the Preferences dialog. With the mode set to Grid, the cursor automatically snaps to the grid, positioning the reference point of the object being placed onto the nearest grid location.


Applied Parameters: Size=7.500MM

Summary

This command is used to set the X (horizontal) and Y (vertical) step values - for the Snap Grid - simultaneously to 7.500mm. These values together define the Snap Grid for manual movement and placement in the current document.

Access

This command is accessed from the CAMtastic Editor, by:

  • Using the G keyboard shortcut, then choosing the 7.500 mm command from the pop-up menu.
  • Choosing the 7.500 mm entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for both the X Grid and Y Grid properties of the Snap Grid will be set to 7.500mm, and the grid will update accordingly in the workspace.

Tips

  1. The X and Y grid values can be changed as required, and independently for the snap grid, by editing the grid through the Enter Grid (1..1000mil) dialog, accessed by using the Ctrl+G keyboard shortcut.
  2. Display of the grid (On/Off), as well as grid sizing (Size X:Y), can also be managed from the CAM Editor - Drawing Modes page of the Preferences dialog. The size drop-down field lists previously used grid values, or simply enter new sizing directly, as required.
  3. The snap grid is used when the Object Snap mode is set to Grid. The object snapping mode can be changed on the CAMtastic panel, or on the CAM Editor - Drawing Modes page of the Preferences dialog. With the mode set to Grid, the cursor automatically snaps to the grid, positioning the reference point of the object being placed onto the nearest grid location.


Applied Parameters: None

Summary

This command is used to set the X (horizontal) and Y (vertical) step values - for the Snap Grid - simultaneously to a chosen value. These values together define the Snap Grid for manual movement and placement in the current document.

Access

This command is accessed from the CAMtastic Editor, by:

  • Using the Ctrl+G keyboard shortcut.
  • Using the G keyboard shortcut, then choosing the Set Snap Grid command from the pop-up menu.
  • Choosing the Set Snap Grid entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the Enter Grid (1..1000mil) dialog will appear. Enter the same, or different values to be used for the X Grid and Y Grid properties of the Snap Grid, and click OK - the grid will update accordingly in the workspace.

Tips

  1. Display of the grid (On/Off), as well as grid sizing (Size X:Y), can also be managed from the CAM Editor - Drawing Modes page of the Preferences dialog. The size drop-down field lists previously used grid values, or simply enter new sizing directly, as required.
  2. The snap grid is used when the Object Snap mode is set to Grid. The object snapping mode can be changed on the CAMtastic panel, or on the CAM Editor - Drawing Modes page of the Preferences dialog. With the mode set to Grid, the cursor automatically snaps to the grid, positioning the reference point of the object being placed onto the nearest grid location.

 

Found an issue with this document? Highlight the area, then use Ctrl+Enter to report it.

Contact Us

Contact our corporate or local offices directly.

You are reporting an issue with the following selected text
and/or image within the active document:
ALTIUM DESIGNER FREE TRIAL
Altium Designer Free Trial
Let’s get started. First off, are you or your organization already using Altium Designer?

If would like to speak with a representative, please contact your local Altium office.
Copyright © 2019 Altium Limited

In that case, why do you need an evaluation license?

If would like to speak with a representative, please contact your local Altium office.
Copyright © 2019 Altium Limited

Got it. You actually don’t need an evaluation license for that.

Click the button below to download the latest Altium Designer installer.

Download Altium Designer Installer

If would like to speak with a representative, please contact your local Altium office.
Copyright © 2019 Altium Limited

Please fill out the form below to get a quote for a new seat of Altium Designer.

By clicking “Get Your Free Trial”, you are agreeing to our Privacy Policy.
You may receive communications from Altium and can change your notification preferences at any time.

If you are on Altium Subscription, you don’t need an evaluation license.

If you are not an active Altium Subscription member, please fill out the form below to get your free trial.

By clicking “Get Your Free Trial”, you are agreeing to our Privacy Policy.
You may receive communications from Altium and can change your notification preferences at any time.

Why are you looking to evaluate Altium Designer?

If would like to speak with a representative, please contact your local Altium office.
Copyright © 2019 Altium Limited

You came to the right place! Please fill out the form below to get your free trial started.

By clicking “Get Your Free Trial”, you are agreeing to our Privacy Policy.
You may receive communications from Altium and can change your notification preferences at any time.

Great News!

Valid students can get their very own 6-month Altium Designer Student License for FREE! Just fill out the form below to request your Student License today.

By clicking “Get Your Free Trial”, you are agreeing to our Privacy Policy.
You may receive communications from Altium and can change your notification preferences at any time.

Got it. You can download a free Altium Designer Viewer license which is valid for a 6 months.

Please fill out the form below to request one.

By clicking “Get Your Free Trial”, you are agreeing to our Privacy Policy.
You may receive communications from Altium and can change your notification preferences at any time.

That’s great! Making things is awesome. We have the perfect program for you.

Upverter is a free community-driven platform designed specifically to meet the needs of makers like you.

Click here to give it a try!

If would like to speak with a representative, please contact your local Altium office.
Copyright © 2019 Altium Limited

Got it. You can download a free Altium Designer Viewer license which is valid for a 6 months.

Please fill out the form below to request one.

By clicking “Get Your Free Trial”, you are agreeing to our Privacy Policy.
You may receive communications from Altium and can change your notification preferences at any time.