Altium NEXUS Documentation

CrossProbeChoose

Created: August 10, 2017 | Updated: August 10, 2017

Parent page: Schematic Commands

The following pre-packaged resources, derived from this base command, are available:


Applied Parameters: None

Summary

This command is used to cross probe from a chosen object on the current schematic document to its corresponding counterpart on the PCB document. Cross-probing is a powerful searching tool to help locate objects in other editors by selecting the object in the current editor. Between the Schematic and PCB Editors, full cross-probing support is provided for documents, components, buses, nets, and pins/pads.

Access

This command can be accessed from the Schematic Editor by:

  • Choosing the Tools » Cross Probe command from the main menus.
  • Clicking the  button on the Schematic Standard toolbar.

Use

There are two cross-probing modes available:

  • Continuous Mode – this mode allows remaining in the source document while cross-probing to different objects on the target document. Simply position the cursor over the required object within the workspace and click, or press Enter. The corresponding object will be highlighted on the target document. Continue cross-probing further objects, or right-click, or press Esc, to exit.
For this mode, it is more efficient to have the schematic (source) and PCB (target) documents open side-by-side in the main design window.
  • Jump To Mode – this mode allows cross-probing to a single object (i.e., 'single-shot cross-probing'), making the target document the active document. Simply position the cursor over the required object within the workspace and Ctrl+click or press Ctrl+Enter. The corresponding object will be highlighted on the target document, with that document becoming the active document.

Tips

  1. When using the command repeatedly in Continuous Mode, the last object chosen will be the one displayed/highlighted. Cross-probe filtering is not cumulative.
  2. The cross-probed objects on the target document will be displayed in accordance with the Highlight Methods defined on the System - Navigation page of the Preferences dialog. Highlighting will not be applied to the originating document.


Applied Parameters: Action=ToggleFastCrossSelect

Summary

This feature facilitates dynamic, bi-directional object cross-selection. It is used to select corresponding objects between schematic and PCB documents. That is, when you select an object on a schematic document, the same object on the PCB document is also selected (and vice-versa). There are many uses for cross-selecting from the schematic to build up a selection of PCB components, three of which include:

Access

This feature is accessed from the Schematic Editor in one of the following ways:

  • Click the Tools » Cross Select Mode command from the main menus.
  • Enable the Cross Selection option in the Cross Select Mode region, on the System - Navigation page of the Preferences dialog.
  • Click Shift+Ctrl+X.

Use

With this feature enabled, simply select one or more objects within the source schematic sheets of the design project. Those same objects will become selected on the PCB document.

Multiple components can be selected in a single action, or you can build up a selection by holding the Shift key and repeatedly clicking to select.
The target document will not be made the active document. It is therefore a good idea to have both source and target documents open side-by-side.

Tips

  1. When enabled, the icon for the feature on the main Tools menu will become highlighted.
  2. Cross Select Mode display behavior is controlled using the Cross Select Mode options on the System - Navigation page of the Preferences dialog. This includes the option to Reposition selected component in PCB. With this enabled, when you click on a component on a schematic, the corresponding component will be attached to the cursor in the PCB, which is made active, ready for placement immediately.
  3. If a document is closed and then reopened, the project must be re-compiled before the feature will work correctly for affected objects on that document.


Applied Parameters: Action=CrossSelect

Summary

This feature facilitates cross-selection between selected parts on one or more schematic source documents and the corresponding component footprints on the PCB document for the active project. This can be useful, for example, in selecting a set of parts on the source documents to create a new component class quickly in the PCB document.

Access

This feature is accessed from the Schematic Editor by choosing the Tools » Select PCB Components command from the main menus.

Use

First, ensure that the target PCB document is open and that the required components are selected on the applicable source schematic documents.

After launching the command, all schematic source documents will be automatically compiled, and the PCB document for the project will then be made the active document. All corresponding component footprints for the selection will become selected and zoomed (but not masked) in the workspace.

As the target PCB will become the active document, it may be a good idea to have the source schematic(s) and PCB document open side-by-side.

Tips

  1. If the active project contains multiple PCB documents, you should open only the document upon which you wish to work/have the components selected. If more than one PCB document is opened, the command will interrogate all documents for a corresponding match to the components selected on the schematic document(s).


Applied Parameters: ContextSensitive=True|Action=CrossSelect

Summary

This feature facilitates cross-selection between selected parts on one or more schematic source documents, and the corresponding component footprints on the PCB document for the active project. This can be useful, for example, in selecting a set of parts on the source documents to create a new component class quickly in the PCB document.

Access

This feature is accessed from the Schematic Editor by right-clicking over the required part (or one part in a selection of parts) and choosing the Part Actions » Select PCB Components command from the context menu.

Use

First, ensure that the target PCB document is open, and that the required components are selected on the applicable source schematic documents. If cross selecting a single part, the part need not be selected.

After launching the command, all schematic source documents will be automatically compiled and the PCB document for the project will then be made the active document. All corresponding component footprints for the selection will become selected and zoomed (but not masked) in the workspace.

As the target PCB will become the active document, it may be a good idea to have the source schematic(s) and PCB document open side-by-side.

Tips

  1. If the active project contains multiple PCB documents, you should open only the document upon which you wish to work/have the components selected. If more than one PCB document is opened, the command will interrogate all documents for a corresponding match to the components selected on the schematic document(s).

 

Found an issue with this document? Highlight the area, then use Ctrl+Enter to report it.

联系我们

联系原厂或当地办公室

We're sorry to hear the article wasn't helpful to you.
Could you take a moment to tell us why?
200 characters remaining
You are reporting an issue with the following selected text
and/or image within the active document: