Altium NEXUS Documentation

PlaceArc

Modified by Susan Riege on Jan 30, 2019

Parent page: Schematic Commands

The following pre-packaged resources, derived from this base command, are available:


Applied Parameters: None

Summary

This command is used to place an Arc object onto the active document, with full control over start and end angles. An arc is a non-electrical drawing primitive. It is essentially a curved line segment which can be used when, for example, creating graphical symbols, custom sheet borders and title blocks.

For detailed information about this object type, see Arc.

Access

Arcs are available for placement in both Schematic and Schematic Library Editors:

  • Schematic Editor - the following commands are available:
    • Choose Place » Drawing Tools » Arc from the main menus.
    • Locate and use the Arc command () on the Active Bar.
      If the command has been recently used from the Active Bar, it will become the active/visible button. Where other commands are available, this is indicated by a triangle at the bottom-right corner of the button. Click and hold on the active button to access a menu of all associated commands for that grouping.
    • Right-click and choose Place » Drawing Tools » Arc from the context menu.
  • Schematic Library Editor - the following commands are available:
    • Choose Place » Arc from the main menus.
    • Locate and use the Arc command () on the Active Bar.
      If the command has been recently used from the Active Bar, it will become the active/visible button. Where other commands are available, this is indicated by a triangle at the bottom-right corner of the button. Click and hold on the active button to access a menu of all associated commands for that grouping.
    • Right-click and choose Place » Arc from the context menu.

Use

After launching the command, the cursor will change to a cross-hair and you will enter arc placement mode. Placement is made by performing the following sequence of actions:

  1. Click or press Enter to anchor the center point of the arc.
  2. Move the cursor to adjust the radius of the arc, then click or press Enter to set it.
  3. Move the cursor to adjust the start angle for the arc, then click or press Enter to anchor it.
  4. Move the cursor to adjust the end angle for the arc, then click or press Enter to anchor it and complete placement of the arc.
  5. Continue placing further arcs, or right-click or press Esc to exit placement mode.
At any time during placement, press the Tab key to access the Properties panel, from where properties for the arc can be changed on-the-fly. Pressing Tab pauses placement, allowing you to interact with the panel (or other area of the software) directly. To resume, click the pause symbol that appears over the workspace.

Additional actions that can be performed during placement – while the arc is still floating on the cursor, and before the center point of the arc is anchored – are:

  • Press the Alt key to constrain the direction of movement to the horizontal or vertical axis, depending on the initial direction of movement.
  • Press the Spacebar to rotate the arc counterclockwise or Shift+Spacebar for clockwise rotation. Rotation is in increments of 90°.
  • Press the X or Y keys to mirror the arc along the X-axis or Y-axis respectively.

Tips

  1. For information on how a placed arc object can be modified graphically, directly in the workspace, see Graphical Editing.
  2. While attributes can be modified during placement (Tab to bring up the Properties panel), bear in mind that these will become the default settings for further placement unless the Permanent option on the Schematic - Defaults page of the Preferences dialog is enabled. When this option is enabled, changes made will affect only the object being placed and subsequent objects placed during the same placement session.


Applied Parameters: StartAngle=0|EndAngle=360|Repeat=True

Summary

This command is used to place a Full Circle Arc object onto the active document, where start and end angles are fixed at 0 and 360 Degrees respectively. An arc is a non-electrical drawing primitive. It is essentially a curved line segment which can be used when, for example, creating graphical symbols, custom sheet borders and title blocks.

For detailed information about this object type, see Arc.

Access

Full Circle Arcs are available for placement in both Schematic and Schematic Library Editors:

  • Schematic Editor - the following commands are available:
    • Choose Place » Drawing Tools » Full Circle from the main menus.
    • Locate and use the Full Circle command () on the Active Bar.
      If the command has been recently used from the Active Bar, it will become the active/visible button. Where other commands are available, this is indicated by a triangle at the bottom-right corner of the button. Click and hold on the active button to access a menu of all associated commands for that grouping.
    • Right-click and choose Place » Drawing Tools » Full Circle from the context menu.
  • Schematic Library Editor - the following commands are available:
    • Choose Place » Full Circle from the main menus.
    • Locate and use the Full Circle command () on the Active Bar.
      If the command has been recently used from the Active Bar, it will become the active/visible button. Where other commands are available, this is indicated by a triangle at the bottom-right corner of the button. Click and hold on the active button to access a menu of all associated commands for that grouping.
    • Right-click and choose Place » Full Circle from the context menu.

Use

After launching the command, the cursor will change to a cross-hair and you will enter arc placement mode. Placement is made by performing the following sequence of actions:

  1. Click or press Enter to anchor the center point of the arc.
  2. Move the cursor to adjust the radius of the arc, then click or press Enter to set it.
  3. Continue placing further arcs, or right-click or press Esc to exit placement mode.
At any time during placement, press the Tab key to access the Properties panel, from where properties for the arc can be changed on-the-fly. Pressing Tab pauses placement, allowing you to interact with the panel (or other area of the software) directly. To resume, click the pause symbol that appears over the workspace.

Additional actions that can be performed during placement – while the arc is still floating on the cursor, and before the center point of the arc is anchored – are:

  • Press the Alt key to constrain the direction of movement to the horizontal or vertical axis, depending on the initial direction of movement.
  • Press the Spacebar to rotate the arc counterclockwise or Shift+Spacebar for clockwise rotation. Rotation is in increments of 90°.
  • Press the X or Y keys to mirror the arc along the X-axis or Y-axis respectively.

Tips

  1. For information on how a placed arc object can be modified graphically, directly in the workspace, see Graphical Editing.
  2. While attributes can be modified during placement (Tab to bring up the Properties panel), bear in mind that these will become the default settings for further placement unless the Permanent option on the Schematic - Defaults page of the Preferences dialog is enabled. When this option is enabled, changes made will affect only the object being placed and subsequent objects placed during the same placement session.

 

Found an issue with this document? Highlight the area, then use Ctrl+Enter to report it.

Contact Us

Contact our corporate or local offices directly.

You are reporting an issue with the following selected text
and/or image within the active document:
ALTIUM DESIGNER FREE TRIAL
Altium Designer Free Trial
Let’s get started. First off, are you or your organization already using Altium Designer?

If would like to speak with a representative, please contact your local Altium office.
Copyright © 2019 Altium Limited

In that case, why do you need an evaluation license?

If would like to speak with a representative, please contact your local Altium office.
Copyright © 2019 Altium Limited

Got it. You actually don’t need an evaluation license for that.

Click the button below to download the latest Altium Designer installer.

Download Altium Designer Installer

If would like to speak with a representative, please contact your local Altium office.
Copyright © 2019 Altium Limited

Please fill out the form below to get a quote for a new seat of Altium Designer.

By clicking “Get Your Free Trial”, you are agreeing to our Privacy Policy.
You may receive communications from Altium and can change your notification preferences at any time.

If you are on Altium Subscription, you don’t need an evaluation license.

If you are not an active Altium Subscription member, please fill out the form below to get your free trial.

By clicking “Get Your Free Trial”, you are agreeing to our Privacy Policy.
You may receive communications from Altium and can change your notification preferences at any time.

Why are you looking to evaluate Altium Designer?

If would like to speak with a representative, please contact your local Altium office.
Copyright © 2019 Altium Limited

You came to the right place! Please fill out the form below to get your free trial started.

By clicking “Get Your Free Trial”, you are agreeing to our Privacy Policy.
You may receive communications from Altium and can change your notification preferences at any time.

Great News!

Valid students can get their very own 6-month Altium Designer Student License for FREE! Just fill out the form below to request your Student License today.

By clicking “Get Your Free Trial”, you are agreeing to our Privacy Policy.
You may receive communications from Altium and can change your notification preferences at any time.

Got it. You can download a free Altium Designer Viewer license which is valid for a 6 months.

Please fill out the form below to request one.

By clicking “Get Your Free Trial”, you are agreeing to our Privacy Policy.
You may receive communications from Altium and can change your notification preferences at any time.

That’s great! Making things is awesome. We have the perfect program for you.

Upverter is a free community-driven platform designed specifically to meet the needs of makers like you.

Click here to give it a try!

If would like to speak with a representative, please contact your local Altium office.
Copyright © 2019 Altium Limited

Got it. You can download a free Altium Designer Viewer license which is valid for a 6 months.

Please fill out the form below to request one.

By clicking “Get Your Free Trial”, you are agreeing to our Privacy Policy.
You may receive communications from Altium and can change your notification preferences at any time.