Связаться с нами
Связаться с нашими Представительствами напрямую
Parent page: PCB Objects
Accordion objects are added to increase the length of a route, the Net Length Gauge indicates the progress towards achieving the required target length.
The accordion object is a system-created group object. The accordion object is created by the software during interactive length tuning to increase the overall length of a route. The software builds the accordion shaped section of routing from tracks and/or arcs in accordance with the properties defined in the Accordion mode of the Properties panel. Because the accordion object is a group object, a placed accordion can be interactively reshaped if required.
The accordion object is placed automatically in the PCB editor when the Interactive Length Tuning command is being used and the route length is shorter than the length specified for that net.
The route length requirement is specified by:
Accordions are placed when the Interactive Length Tuning command is run, and the route length needs to be increased.
After launching the PCB editor's Route » Interactive Length Tuning command, the cursor will change to a cross-hair and you will enter length tuning (Accordion placement) mode. Placement is made by performing the following sequence of actions:
Additional actions that can be performed during placement include:
The shortcuts available during length tuning include:
Shortcut | Function |
---|---|
Spacebar | Cycle through the three Styles of tuning pattern |
, (comma) | Decrease amplitude by the amount specified for the Amplitude Increment |
. (full stop) | Increase amplitude by the amount specified for the Amplitude Increment |
3 | Decrease space by the amount specified for the Gap Increment |
4 | Increase space by the amount specified for the Gap Increment |
1 | Decrease corner miter by the % specified for the Miter Increment |
2 | Increase corner miter by the % specified for the Miter Increment |
Y | Toggle starting direction |
Tab | Open the Properties panel in Accordion mode |
Shift+G | Toggle Length Tuning Gauge on/off |
This method of editing allows you to select a placed Accordion object directly in the workspace and graphically change its size and shape.
When an Accordion object is selected, its polygonal outline is displayed as shown in the animation below. The outer shape of the polygonal outline is defined by a series of edges: where each edge is represented by an end vertex at each end,
shown as a solid white square (A in the image below); and a center vertex in the middle, shown as a hollow white square (B in the image below). Each end vertex represents the location where two edges meet.Click and drag on an edge or a vertex to reshape the accordion's polygonal outline, press Shift+Space to change the editing mode.
Standard polygonal shape editing techniques are available for editing the shape.
When editing a polygonal object, there are three editing modes available, Slide/Miter, Incurvate (arc) and Move. The current mode can be changed while dragging a vertex or an edge by pressing Shift+Spacebar to cycle through the three modes.
The following methods of non-graphical editing are available:
Properties page: Accordion Properties
This method of editing uses the associated Accordion dialog and Properties panel to modify the properties of an Accordion object.
The Accordion dialog on the left and the Accordion mode of the Properties panel on the right.
During interactive length tuning, the Properties panel can be accessed by pressing the Tab key.
After placement, the Accordion dialog can be accessed by:
After placement, the Accordion mode of the Properties panel can be accessed in one of the following ways:
The properties displayed in the panel and dialog reflect the settings that were used to create the selected accordion.
The Properties panel supports editing multiple objects, where the property settings that are identical in all currently selected objects may be modified. When multiples of the same object type are selected manually, via the Find Similar Objects dialog or through a Filter or List panel, a Properties panel field entry that is not shown as an asterisk (*
) may be edited for all selected objects.
Panel page: PCB List
The List panel allows you to display design objects from one or more documents in tabular format, enabling quick inspection and modification of object attributes. Used in conjunction with appropriate filtering - by using the applicable Filter panel, or the Find Similar Objects dialog - it enables the display of just those objects falling under the scope of the active filter – allowing you to target and edit multiple design objects with greater accuracy and efficiency.
Связаться с нашими Представительствами напрямую
Если Вы хотите поговорить с представителем, пожалуйста, свяжитесь с местным офисом Altium.
Copyright © 2019 Altium Limited
Если Вы хотите поговорить с представителем, пожалуйста, свяжитесь с местным офисом Altium.
Copyright © 2019 Altium Limited
Вам для этого не нужна пробная лицензия.
Нажмите кнопку ниже, чтобы загрузить установщик самой новой версии Altium Designer
Если Вы хотите поговорить с представителем, пожалуйста, свяжитесь с местным офисом Altium.
Copyright © 2019 Altium Limited
Пожалуйста, заполните форму ниже, чтобы получить ценовое предложение.
Нажимая [Получить бесплатнную пробную версию], Вы соглашаетесь с нашей Политикой конфиденциальности. Вам могут приходить сообщения от компании Altium, и Вы можете изменить настройки уведомлений в любой момент.
Если Ваша подписка Altium активна, у Вас нет необходимости в пробной лицензии.
Если у Вас нет активной подписки Altium, пожалуйста, заполните форму ниже, чтобы получить пробную версию.
Нажимая [Получить бесплатнную пробную версию], Вы соглашаетесь с нашей Политикой конфиденциальности. Вам могут приходить сообщения от компании Altium, и Вы можете изменить настройки уведомлений в любой момент.
Если Вы хотите поговорить с представителем, пожалуйста, свяжитесь с местным офисом Altium.
Copyright © 2019 Altium Limited
Вы нашли нужное место! Пожалуйста, заполните форму ниже, чтобы начать использование пробной версии.
Нажимая [Получить бесплатнную пробную версию], Вы соглашаетесь с нашей Политикой конфиденциальности. Вам могут приходить сообщения от компании Altium, и Вы можете изменить настройки уведомлений в любой момент.
Great News!
Valid students can get their very own 6-month Altium Designer Student License for FREE! Just fill out the form below to request your Student License today.
Нажимая [Получить бесплатнную пробную версию], Вы соглашаетесь с нашей Политикой конфиденциальности. Вам могут приходить сообщения от компании Altium, и Вы можете изменить настройки уведомлений в любой момент.
Вы можете загрузить бесплатную лицензию средства просмотра Altium Designer Viewer сроком действия 6 месяцев.
Пожалуйста, заполните форму ниже, чтобы запросить эту лицензию.
Нажимая [Получить бесплатнную пробную версию], Вы соглашаетесь с нашей Политикой конфиденциальности. Вам могут приходить сообщения от компании Altium, и Вы можете изменить настройки уведомлений в любой момент.
Замечательно! Создавать новое - отличное занятие. У нас есть превосходная программа для Вас.
Upverter - бесплатная платформа, разработанная специально для любителей проектирования.
Нажмите здесь, чтобы попробовать!
Если Вы хотите поговорить с представителем, пожалуйста, свяжитесь с местным офисом Altium.
Copyright © 2019 Altium Limited
Вы можете загрузить бесплатную лицензию средства просмотра Altium Designer Viewer сроком действия 6 месяцев.
Пожалуйста, заполните форму ниже, чтобы запросить эту лицензию.
Нажимая [Получить бесплатнную пробную версию], Вы соглашаетесь с нашей Политикой конфиденциальности. Вам могут приходить сообщения от компании Altium, и Вы можете изменить настройки уведомлений в любой момент.