Altium NEXUS Documentation

ManageGridsAndGuides

Modified by Susan Riege on Aug 1, 2018

Parent page: PCB Commands

The following pre-packaged resource, derived from this base command, is available:


Applied Parameters: Action=ShowGridPropertiesUnderCursor

Summary

This command is used to quickly access the dedicated grid editor dialog for the snap grid currently under the cursor.

Access

With the cursor over the grid of interest, this command is accessed from the PCB Editor and PCB Library Editor by:

  • Using the Ctrl+G keyboard shortcut.
  • Using the G keyboard shortcut, then choosing the Grid Properties entry on the subsequent pop-up menu.

Use

After launching the command, the applicable grid editing dialog will open - either the Cartesian Grid Editor dialog or the Polar Grid Editor dialog. Use the dialog to make changes to the definition of the grid, as required.

Tips

  1. Hover the cursor over the grid of interest - do not click in the workspace prior to launching the command.
  2. Where a number of grids overlap, the highest priority grid will be the one accessed for editing. In the workspace, priority is distinguished by drawing order. The highest priority grid (priority 1) will be drawn in front of all other grids, then the grid with priority level 2, and so on, down to the default Global Board Snap Grid, which is drawn behind all other custom grids.
  3. Grids for the workspace are managed through the Grid Manager section of the Properties panel (when no objects are currently selected in the design workspace).


Applied Parameters: Action=PlaceHorzLineGuide

Summary

This command is used to place a horizontal guideline at the desired Y-coordinate location in the workspace. Linear Snap Guides such as this facilitate cursor snap to a specific axis. During an interactive process such as placing or moving, the cursor will snap to a placed guide at the point where that guide intersects the applicable snap grid. Using a guide, objects can quickly be aligned simply by dragging them until they 'snap' against the guideline.

For detailed information on working with guides, see PCB Grids System.

Access

This command is accessed from the PCB Editor by choosing the Place » Work Guides » Place Horizontal Guide command from the main menus.

Use

After launching the command, the cursor will change to a cross-hair and you will be prompted to choose a location for the horizontal guideline. Position the cursor then click or press Enter - the guideline will appear, running horizontally through the chosen point.

Continue placing further horizontal guidelines or right-click or press Esc to exit placement mode.

Tips

  1. The guide will be colored using a default yellow color (RGB = 250, 236, 133). Post-placement, this can be changed, along with position, and whether or not the guide is enabled, only through the Guide Manager section of the Properties panel, when no design objects are currently selected in the design workspace.


Applied Parameters: Action=PlaceVertLineGuide

Summary

This command is used to place a vertical guideline at the desired X-coordinate location in the workspace. Linear Snap Guides such as this facilitate cursor snap to a specific axis. During an interactive process such as placing or moving, the cursor will snap to a placed guide at the point where that guide intersects the applicable snap grid. Using a guide, objects can quickly be aligned simply by dragging them until they 'snap' against the guideline.

For detailed information on working with guides, see PCB Grids System.

Access

This command is accessed from the PCB Editor by choosing the Place » Work Guides » Place Vertical Guide command from the main menus.

Use

After launching the command, the cursor will change to a cross-hair and you will be prompted to choose a location for the vertical guideline. Position the cursor then click or press Enter - the guideline will appear, running vertically through the chosen point.

Continue placing further vertical guidelines or right-click or press Esc to exit placement mode.

Tips

  1. The guide will be colored using a default yellow color (RGB = 250, 236, 133). Post-placement, this can be changed, along with position, and whether or not the guide is enabled, only through the Guide Manager section of the Properties panel when no design objects are currently selected in the design workspace.


Applied Parameters: Action=PlacePlus45DegLineGuide

Summary

This command is used to place a 45 degree (y=x) guideline that passes through the desired X,Y coordinate location in the workspace. Linear Snap Guides such as this facilitate cursor snap to a specific axis. During an interactive process such as placing or moving, the cursor will snap to a placed guide at the point where that guide intersects the applicable snap grid. Using a guide, objects can quickly be aligned simply by dragging them until they 'snap' against the guideline.

For detailed information on working with guides, see PCB Grids System.

Access

This command is accessed from the PCB Editor by choosing the Place » Work Guides » Place +45 Degree Guide command from the main menus.

Use

After launching the command, the cursor will change to a cross-hair and you will be prompted to choose a location for the +45 Degree guideline. Position the cursor then click or press Enter - the guideline will appear, running at 45 Degrees through the chosen point.

Continue placing further +45 Degree guidelines or right-click or press Esc to exit placement mode.

Tips

  1. The guide will be colored using a default yellow color (RGB = 250, 236, 133). Post-placement, this can be changed, along with position, and whether or not the guide is enabled, only through the Guide Manager section of the Properties panel when no design objects are currently selected in the design workspace.


Applied Parameters: Action=PlaceMinus45DegLineGuide

Summary

This command is used to place a -45 degree (y=-x) guideline that passes through the desired X,Y coordinate location in the workspace. Linear Snap Guides such as this facilitate cursor snap to a specific axis. During an interactive process such as placing or moving, the cursor will snap to a placed guide, at the point where that guide intersects the applicable snap grid. Using a guide, objects can quickly be aligned simply by dragging them until they 'snap' against the guideline.

For detailed information on working with guides, see PCB Grids System.

Access

This command is accessed from the PCB Editor by choosing the Place » Work Guides » Place -45 Degree Guide command from the main menus.

Use

After launching the command, the cursor will change to a cross-hair and you will be prompted to choose a location for the -45 Degree guideline. Position the cursor then click or press Enter - the guideline will appear, running at -45 Degrees through the chosen point.

Continue placing further -45 Degree guidelines or right-click or press Esc to exit placement mode.

Tips

  1. The guide will be colored using a default yellow color (RGB = 250, 236, 133). Post-placement, this can be changed, along with position, and whether or not the guide is enabled, only through the Guide Manager section of the Properties panel when no design objects are currently selected in the design workspace.


Applied Parameters: Action=PlaceManualHotSpot

Summary

This command is used to place a point Snap Guide – a manual snap point if you will. A point snap guide is simply a hotspot that you manually mark within the confines of a defined grid. During an interactive process, such as placing or moving an object, that objects' hotspot will 'snap' to a point snap guide, when it passes into close proximity with it.

For detailed information on working with guides, see PCB Grids System.

Access

This command is accessed from the PCB Editor by choosing the Place » Work Guides » Place Point Guide command from the main menus.

Use

After launching the command, the cursor will change to a cross-hair and you will be prompted to choose a location for the manual hotspot. Position the cursor then click or press Enter - the point guide will appear, marked by a cross at the chosen point.

Continue placing further point guides or right-click or press Esc to exit placement mode.

Tips

  1. The guide will be colored using a default yellow color (RGB = 250, 236, 133). Post-placement, this can be changed, along with position, and whether or not the guide is enabled, only through the Guide Manager section of the Properties panel when no design objects are currently selected in the design workspace.

 

Found an issue with this document? Highlight the area, then use Ctrl+Enter to report it.

联系我们

联系原厂或当地办公室

You are reporting an issue with the following selected text
and/or image within the active document:
Altium Designer 免费试用
Altium Designer Free Trial
我们开始吧!首先,您或者您的公司已经在使用Altium Designer了吗?

如果您有任何需求,请点击这里联系获取当地办公室销售代表联系方式。.
Copyright © 2019 Altium Limited

既然您在使用Altium Designer,为何仍需要试用?

如果您有任何需求,请点击这里联系获取当地办公室销售代表联系方式。.
Copyright © 2019 Altium Limited

好的,实际上您无需下载一个试用版本。

点击下方按钮下载最新版本的Altium Designer安装包

下载Altium Designer 安装包

如果您有任何需求,请点击这里联系获取当地办公室销售代表联系方式。.
Copyright © 2019 Altium Limited

填写下方表格,获取Altium Designer最新报价。

点击[获取免费试用],并同意我们的隐私政策。您会接收到来自Altium的资讯,并允许其改变您的通知首选项。

如果您是Altium维保期内客户,您不需要下载试用版本。

如果您不是Altium维保客户,请填写下方表格免费试用。

点击[获取免费试用],并同意我们的隐私政策。您会接收到来自Altium的资讯,并允许其改变您的通知首选项。

您为何想要试用Altium Designer?

如果您有任何需求,请点击这里联系获取当地办公室销售代表联系方式。.
Copyright © 2019 Altium Limited

那您来对地方了!请填写下方表格申请试用吧。

点击[获取免费试用],并同意我们的隐私政策。您会接收到来自Altium的资讯,并允许其改变您的通知首选项。

Great News!

Valid students can get their very own 6-month Altium Designer Student License for FREE! Just fill out the form below to request your Student License today.

点击[获取免费试用],并同意我们的隐私政策。您会接收到来自Altium的资讯,并允许其改变您的通知首选项。

好的,您可以下载免费的Altium Designer Viewer查看文档,有效期6个月。

请填写下方表格申请。

点击[获取免费试用],并同意我们的隐私政策。您会接收到来自Altium的资讯,并允许其改变您的通知首选项。

好棒!创作是一件超酷的事情,我们可以为您提供完美的设计软件。

Upverter是一个社区导向的交流平台,专为您这样的创客量身定做。

点击这里看看吧!

如果您有任何需求,请点击这里联系获取当地办公室销售代表联系方式。.
Copyright © 2019 Altium Limited

好的,您可以下载免费的Altium Designer Viewer查看文档,有效期6个月。

请填写下方表格申请。

点击[获取免费试用],并同意我们的隐私政策。您会接收到来自Altium的资讯,并允许其改变您的通知首选项。