Design Rule Checking (DRC) is a powerful automated feature that checks both the logical and physical integrity of a design. Checks are made against any or all enabled Design Rules and can be made online in real-time as you design or as a batch process, with results listed in the software's Messages panel and a (optional) generated report.
This feature should be used on every routed board to confirm that minimum clearance rules have been maintained and that there are no other design violations. It is particularly recommended that a batch mode design rule check always be performed prior to generating final artwork.
In the folder-tree pane on the left side of the dialog, each of the design rule categories whose rule types can be checked are listed under the Rules To Check folder. Click on this top-level folder to list all checkable rule types on the right side of the dialog. Alternatively, click on a specific category to list only those design rule types associated to that category. Use the dialog to enable/disable Online (where available) and/or Batch Mode checking for each rule type you wish to check.
Online Design Rule Checking runs in the background, in real-time, flagging and/or automatically preventing design rule violations. This is especially helpful when interactively routing your board to immediately highlight clearance, width and parallel segment violations. For a rule to be subject to the Online DRC, the following three requirements must be met:
If any objects are found to be in violation of an applicable design rule that is enabled for online checking, they will be highlighted in the main workspace in accordance with defined violation display options.
Whereas Online DRC only detects new violations - violations that are created after the feature is enabled - Batch DRC allows a check to be manually run at any time during the board design process. So while good designers know the value of Online DRC, they also know that board design should begin and end with a Batch DRC.
Enable rule types for batch checking in the Design Rule Checker dialog as required (refer back to the Configuring the DRC section). Various additional options are available when running a Batch DRC, including the ability to generate a report file. These options are accessed by clicking on the Report Options folder in the folder-tree pane of the dialog. Two key options (highlighted in the following image) are:
A batch-mode DRC is initiated by clicking the Run Design Rule Check button at the bottom-left of the dialog. After the check has completed, all violations are listed as messages in the Messages panel. If you opted to do so, a DRC report will be created and automatically opened (if configured to do so) as the active document in the main design window. The report lists each rule that was tested as specified in the Design Rule Checker dialog. Rules that are not present in the design are not tested.
Enabling the Create Report File option in the Design Rule Checker dialog will generate a DRC report upon execution of a Batch DRC. Options available on the PCB Editor - Reports page of the Preferences dialog allow specification of report format, and whether the report is automatically displayed after generation.
Supported formats are:
The report lists each rule that was tested during the batch checking process as specified in the Design Rule Checker dialog. Each violation that was located is listed with full details of any reference information, such as the layer, net name, component designator, and pad number, as well as the location of the object.
Checking the design against specified design rules is one thing, but what happens when one or more of those rule are violated? Whether running Online DRC during design or manually running a Batch DRC, there needs to be some visual indication of where such rule violations are occurring. The PCB Editor includes powerful violation display options to indicate where violations exist in a clear, visual way.
Most design rules that can be included in either Online and/or Batch design rule checking have associated custom violation graphics - appearing within the workspace when a particular rule is violated. These graphics provide a visually cleaner DRC landscape. When a particular design rule is violated, the associated custom violation graphics (where applicable) are only drawn on the layer(s) involved with that violation.
In some cases, the graphic shows not only where the violation is occurring, but also why - displaying the constraint value defined for the rule and indicating how the offending primitive(s) are either below or above this value.
Other graphics, including those used to represent violations of Net Antennae, Short-Circuit, Un-Routed Net, Room Definition, Layer Pairs and Vias Under SMD rules will simply be a graphic, as there is no definable constraint value to be displayed.
In addition to the custom violation graphics, a violations 'overlay' is available for setup and use. The overlay draws over design primitives. You have a choice of what pattern to display on the primitives from a selection of styles.
Using a combination of the two violation display types can prove useful in terms of providing a 'coarse' and 'fine' indication of violations. When zoomed out, the violation overlay can flag where a violation exists, then zoom in to view the detail delivered by the associated custom violation graphic.
Control over how DRC violations are displayed - using the custom violation graphics and/or a defined violation overlay - is specified on the PCB Editor - DRC Violations Display page of the Preferences dialog.
Options available allow you to:
To give further flexibility when displaying rule violations in the workspace, the two violation display types - violation details (custom violation graphics) and violation overlay - have separate associated system colors. This allows you to differentiate between the two using different, distinct colors. Color assignment is performed in the System Colors section on the Layers & Colors tab of the View Configuration panel:
With care and attention and staged design rule checking along the way, running that final Batch DRC on the finished, fully routed board may yield only a few design violations, if any. However, there may be a sizable quantity of violations flagged, and now the task becomes one of resolving those violations.
DRC reports generated by running a Batch DRC can appear quite daunting to the new PCB designer. The secret to keeping the process manageable is to develop a strategy. One strategy is to limit the number of violations that are reported. When setting up the report options in the Design Rule Checker dialog, set the Stop When Found feature to a small number. Another strategy is to run the DRC in a number of stages. If the design contains a large number of violations, begin by enabling the rules one at a time. With experience, you will develop a preferred approach to testing the various design rules.
To effectively resolve a design violation, you must first be able to locate it. The PCB Editor provides various methods for interrogating design violations, as described in the following sections.
When running an Online or Batch DRC, any rule violations will be listed in the Violations region of the PCB Rules And Violations panel. Browse violations associated with a specific rule class or individual rule within a class. Alternatively, browse all violations by selecting the [All Rules] class.
Clicking on a violation entry will apply filtering using the offending object(s) as the scope of the filter. The resulting view in the main design window will depend on the highlighting options enabled (Mask/Dim/Normal, Select, Zoom) at the top of the panel.
Double-clicking on a violation entry (or right-clicking and choosing Properties) will open the Violation Details dialog, which provides information about the rule being violated and the primitive(s) responsible. From this dialog the offending object can be highlighted (causing it to flash in the workspace) and jumped to, effectively providing 'zoom and center'.
After running a Batch DRC, double-clicking on a violation message in the Messages panel will cross-probe to the object(s) causing that violation in the workspace.
If the option to Create Report File is enabled in the Design Rule Checker dialog, violations detected upon running a Batch DRC will be listed in a generated Design Rule Verification Report. Click on the hyperlinked entry for an offending object to cross-probe directly to that object in the workspace.
Violations associated with a particular design object can be interrogated directly within the PCB workspace. Position the cursor over an offending object, right-click and choose a command from the Violations sub-menu. Either choose to investigate an individual violation in which the object is involved or choose to view all violations in which it is involved using the Show All Violations command. In each case, the Violation Details dialog will open, providing detailed violation information and controls for highlighting and jumping to the offending object(s).
Violations can also be browsed directly in the workspace using the Board Insight pop-up. Position the cursor over an object in violation and toggle display of the pop-up using the Shift+V keyboard shortcut. Click on a violation entry to access a menu of commands, including Properties, which gives access to the Violation Details dialog. Expand an entry to browse the primitive(s) involved.
The software supports the ability to selectively waive any DRC violation. This allows you to effectively 'suppress' a violation that is considered not to be an issue without having to craft a special (and maybe complex) design rule to facilitate the design situation.
DRC violations can be waived by:
Against each waived violation, the software records three pieces of information. When waiving from the Messages panel or PCB Rules And Violations panel, this information is entered in the Waived Violation Info dialog. In the Violation Details dialog, fields for this information are available once the Waive this violation option is enabled.
Information stored for a waived violation:
Note that these edits apply to all of the selected violations that are being waived.
Waived violations are listed in the lower section of the PCB Rules and Violations panel as shown in the image below. Note that this section only appears when there are waived violations present in the design.
Click on a waived violation entry to jump to that violation in the workspace (provided the Zoom option is enabled at the top of the panel). Double-click to both jump to the violation (provided Zoom option enabled) and access the Violation Details dialog with the violation presented.
The waived status for a violation can be revoked at any time by:
In the PCB Rules And Violations panel, a waived violation that is unwaived will be removed from the Waived Violations region of the panel and appear listed in the Violations region.
Waived violations are also reported as part of a generated Design Rule Verification Report provided the option to Create Report File is enabled in the Design Rule Checker dialog.
Altium Designer provides the ability to define and run a DRC validation report as part of an Output Job Configuration file (*.OutJob). With an OutJob file open as the active document, the report is available from the Validation Outputs grouping of outputs. To add a report, click the [Add New Validation Output] control and choose the Design Rules Check entry and select the PCB document as the source.
Using validation reports defined in an assigned Output Job file, the software provides the ability to validate designs as an integral part of its board design release process. These validation checks will be performed on every release, and the release will fail if any validation checks are not passed successfully. Validation is run at the Validate Project stage within the Release view with results available at the Review Data stage.