Altium NEXUS Documentation

Footprint Wizard

Created: 08.11.2018 | Updated: 08.11.2018

The Footprint Wizard  is used to create a new component footprint within the current PCB Library Editor document. The Wizard will lead you through steps to define layout, pad spacing, and other component attributes.

For more information about creating a component Footprint, see the Creating the PCB Footprint page.

Using the Footprint Wizard

The Footprint Wizard  is launched by clicking Tools » Footprint Wizard from a PCB Library document (*.PcbLib).

Wizard Navigation

  • Click Cancel to close the Footprint Wizard.
  • Click Back to navigate to the previous screen.
  • Click Next to navigate to the next screen.
  • Click Finish to close the Footprint Wizard. This option is available only on the final page of the Wizard.

Selecting Component Patterns

Use the Component patterns page to specify the pattern of the component you want to create. 

Select the desired pattern from the list then use the drop-down to select the unit for the component (Imperial (mil) or Metric (mm)).

The subsequent pages of the Wizard change depending upon the component pattern selected. Find the desired component pattern in the following list then click on the link to access the information regarding that component pattern.

Ball Grid Arrays (BGA)

To change the pads' diameters, click on the value and enter the new value.

To change the pad to pad distances, click on the values and enter the new value.

To change the outline width, click on the value and enter the new value.

Use the drop-down to select either Alpha Numeric or Numeric naming style.

Use the up and down arrows in each region to define the footprint value for Cutout, Center, Rows and columns, and Corner.

Capacitors

Use the drop-down to select the type of capacitor you want to design. Choose from Through Hole or Surface Mount.

To change the pads' dimensions, click on the values and enter the new values.

This page will have a slightly different look if Surface Mount was selected, however, its functionality is the same. 

To change the pads positioning, click on the value and enter the new value.

This page will have a slightly different look if Surface Mount was selected, however, its functionality is the same. 

This page appears if Through Hole was selected. If Surface Mount was selected, the page below appears.

Use the drop-down to select the capacitor's polarity, either Not Polarised or Polarised. Use the drop-down to select the capacitor's mounting style, either Axial or Radial.

This page appears if Surface Mount was selected. 

Use the drop-down to select outline type, either Non polarised Outline or Polarised Outline

To change the outline dimensions, click on the values and enter the new values.

This page will have a slightly different look if Surface Mount was selected, however, its functionality is the same. 

Diodes

Use the drop-down to select the type of diode you want to design. Choose from Through Hole or Surface Mount.

To change the pads' dimensions, click on the values and enter the new values.

This page will have a slightly different look if Surface Mount was selected, however, its functionality is the same. 

To change the pads positioning, click on the value and enter the new value.

This page will have a slightly different look if Surface Mount was selected, however, its functionality is the same. 

To change the outline dimensions, click on the value and enter the new value.

This page will have a slightly different look if Surface Mount was selected, however, its functionality is the same. 

Dual In-line Packages (DIP)

To change the pads' dimensions, click on the value and enter the new required value.

To change the pads' layout, click on the value and enter the new required value.

To change the outline width, click on the value and enter the new required value.

Use the up and down arrows to select the total number of pads.

Edge Connectors

To change the pads' dimensions, click on the value and enter the new required value.

To change the pad to pad distance, click on the value and enter the new required value.

Use the up and down arrows to select the number of pads. Click the green arrow to change the naming order. The arrow will dynamically change to display the order.

Leadless Chip Carriers (LCC)

To change the pads' dimensions, click on the value and enter the new required value.

Use the drop-down to choose the pads' shapes. Select from Round or Rectangular for For the first pad, then select Round or Rectangular for For the other pads.

To change the outline width, click on the value and enter the new required value.

To change the pads' positioning, click on the value and enter the new required value.

Click one of the radio buttons to select the first pad's location. Choose the naming direction by clicking on the green arrow. The arrow will dynamically update to display the order.

Use the up and down arrows to select the number of pads for both X and Y.

Pin Grid Arrays (PGA)

To change the pads' dimensions, click on the value and enter the new required value.

To change the pad to pad distances, click on the value and enter the new required value.

To change the outline width, click on the value and enter the new required value.

Use the drop-down to select the pads naming style, either Alpha Numeric or Numeric.

Use the up and down arrows in each region to define the footprint value for Cutout, Center, Rows and columns, and Corner.

Quad Packs (QUAD)

To change the pads' dimensions, click on the value and enter the new required value.

Use the drop-down to choose the pads' shapes. Select from Round or Rectangular for For the first pad, then select Round or Rectangular for For the other pads.

To change the outline width, click on the value and enter the new required value.

To change the pads' positioning, click on the value and enter the new required value.

Click one of the radio buttons to select the first pad's location. Choose the naming direction by clicking on the green arrow. The arrow will dynamically update to display the order.

Use the up and down arrows to select the number of pads for both X and Y.

Resistors

Defining the Board Technology

Select the type of resistor you want to design from the drop-down. Choices include Through Hole or Surface Mount.

Defining the Pads Dimensions

To change the pads' dimensions, click on the value and enter the new value.

This page will have a slightly different look if Surface Mount was selected, however, its functionality is the same. 

To change the pad to pad distance, click on the value and enter the new value.

This page will have a slightly different look if Surface Mount was selected, however, its functionality is the same. 

To change the outline dimensions, click on the value and enter the new value.

This page will have a slightly different look if Surface Mount was selected, however, its functionality is the same. 

Small Outline Packages (SOP)

To change the pads' dimensions, click on the value and enter the new value.

To change the pad to pad distance, click on the value and enter the new value.

To change the outline width, click on the value and enter the new value.

Use the up and down arrows to select the total number of pads.

Staggered Ball Grid Arrays (SBGA)

To change the pads' dimensions, click on the value and enter the new value.

To change the pad to pad distance, click on the value and enter the new value.

To change the outline width, click on the value and enter the new value.

Use the drop-down to select the pads naming style, either Alpha Numeric or Numeric.

Use the up and down arrows in each region to define the footprint value for Cutout, Center, Rows and columns, and Corner.

Staggered Pin Grid Arrays (SPGA)

To change the pads' dimensions, click on the value and enter the new value.

To change the pad to pad distance, click on the value and enter the new value.

To change the outline width, click on the value and enter the new value.

Use the drop-down to select the pads' naming style, either Alpha Numeric or Numeric.

Use the up and down arrows in each region to define the footprint value for Cutout, Center, Rows and columns, and Corner.

Setting the Component Name

Enter a name for the component in the textbox. 

Completing and Closing the Wizard

Click Finish to close the Wizard.

Обнаружили проблему в этом документе? Выделите область и нажмите Ctrl+Enter, чтобы оповестить нас.

Связаться с нами

Связаться с нашими Представительствами напрямую

We're sorry to hear the article wasn't helpful to you.
Could you take a moment to tell us why?
200 characters remaining
Вы сообщаете о проблеме, связанной со следующим выделенным текстом
и/или изображением в активном документе: