Altium NEXUS Documentation

SnapGrid

Modified by Jason Howie on Apr 11, 2017

Parent page: CAMtastic Commands

The following pre-packaged resources, derived from this base command, are available:


Applied Parameters: Size=1Mil

Summary

This command is used to set the X (horizontal) and Y (vertical) step values - for the Snap Grid - simultaneously to 1mil. These values together define the Snap Grid for manual movement and placement in the current document.

Access

This command is accessed from the CAMtastic Editor, by:

  • Using the G keyboard shortcut, then choosing the 1 Mil command from the pop-up menu.
  • Choosing the 1 Mil entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for both the X Grid and Y Grid properties of the Snap Grid will be set to 1mil, and the grid will update accordingly in the workspace.

Tips

  1. The X and Y grid values can be changed as required, and independently for the snap grid, by editing the grid through the Enter Grid (1..1000mil) dialog, accessed by using the Ctrl+G keyboard shortcut.
  2. Display of the grid (On/Off), as well as grid sizing (Size X:Y), can also be managed from the CAM Editor - Drawing Modes page of the Preferences dialog. The size drop-down field lists previously used grid values, or simply enter new sizing directly, as required.
  3. The snap grid is used when the Object Snap mode is set to Grid. The object snapping mode can be changed on the CAMtastic panel, or on the CAM Editor - Drawing Modes page of the Preferences dialog. With the mode set to Grid, the cursor automatically snaps to the grid, positioning the reference point of the object being placed onto the nearest grid location.


Applied Parameters: Size=5Mil

Summary

This command is used to set the X (horizontal) and Y (vertical) step values - for the Snap Grid - simultaneously to 5mil. These values together define the Snap Grid for manual movement and placement in the current document.

Access

This command is accessed from the CAMtastic Editor, by:

  • Using the G keyboard shortcut, then choosing the 5 Mil command from the pop-up menu.
  • Choosing the 5 Mil entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for both the X Grid and Y Grid properties of the Snap Grid will be set to 5mil, and the grid will update accordingly in the workspace.

Tips

  1. The X and Y grid values can be changed as required, and independently for the snap grid, by editing the grid through the Enter Grid (1..1000mil) dialog, accessed by using the Ctrl+G keyboard shortcut.
  2. Display of the grid (On/Off), as well as grid sizing (Size X:Y), can also be managed from the CAM Editor - Drawing Modes page of the Preferences dialog. The size drop-down field lists previously used grid values, or simply enter new sizing directly, as required.
  3. The snap grid is used when the Object Snap mode is set to Grid. The object snapping mode can be changed on the CAMtastic panel, or on the CAM Editor - Drawing Modes page of the Preferences dialog. With the mode set to Grid, the cursor automatically snaps to the grid, positioning the reference point of the object being placed onto the nearest grid location.


Applied Parameters: Size=10Mil

Summary

This command is used to set the X (horizontal) and Y (vertical) step values - for the Snap Grid - simultaneously to 10mil. These values together define the Snap Grid for manual movement and placement in the current document.

Access

This command is accessed from the CAMtastic Editor, by:

  • Using the G keyboard shortcut, then choosing the 10 Mil command from the pop-up menu.
  • Choosing the 10 Mil entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for both the X Grid and Y Grid properties of the Snap Grid will be set to 10mil, and the grid will update accordingly in the workspace.

Tips

  1. The X and Y grid values can be changed as required, and independently for the snap grid, by editing the grid through the Enter Grid (1..1000mil) dialog, accessed by using the Ctrl+G keyboard shortcut.
  2. Display of the grid (On/Off), as well as grid sizing (Size X:Y), can also be managed from the CAM Editor - Drawing Modes page of the Preferences dialog. The size drop-down field lists previously used grid values, or simply enter new sizing directly, as required.
  3. The snap grid is used when the Object Snap mode is set to Grid. The object snapping mode can be changed on the CAMtastic panel, or on the CAM Editor - Drawing Modes page of the Preferences dialog. With the mode set to Grid, the cursor automatically snaps to the grid, positioning the reference point of the object being placed onto the nearest grid location.


Applied Parameters: Size=20Mil

Summary

This command is used to set the X (horizontal) and Y (vertical) step values - for the Snap Grid - simultaneously to 20mil. These values together define the Snap Grid for manual movement and placement in the current document.

Access

This command is accessed from the CAMtastic Editor, by:

  • Using the G keyboard shortcut, then choosing the 20 Mil command from the pop-up menu.
  • Choosing the 20 Mil entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for both the X Grid and Y Grid properties of the Snap Grid will be set to 20mil, and the grid will update accordingly in the workspace.

Tips

  1. The X and Y grid values can be changed as required, and independently for the snap grid, by editing the grid through the Enter Grid (1..1000mil) dialog, accessed by using the Ctrl+G keyboard shortcut.
  2. Display of the grid (On/Off), as well as grid sizing (Size X:Y), can also be managed from the CAM Editor - Drawing Modes page of the Preferences dialog. The size drop-down field lists previously used grid values, or simply enter new sizing directly, as required.
  3. The snap grid is used when the Object Snap mode is set to Grid. The object snapping mode can be changed on the CAMtastic panel, or on the CAM Editor - Drawing Modes page of the Preferences dialog. With the mode set to Grid, the cursor automatically snaps to the grid, positioning the reference point of the object being placed onto the nearest grid location.


Applied Parameters: Size=25Mil

Summary

This command is used to set the X (horizontal) and Y (vertical) step values - for the Snap Grid - simultaneously to 25mil. These values together define the Snap Grid for manual movement and placement in the current document.

Access

This command is accessed from the CAMtastic Editor, by:

  • Using the G keyboard shortcut, then choosing the 25 Mil command from the pop-up menu.
  • Choosing the 25 Mil entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for both the X Grid and Y Grid properties of the Snap Grid will be set to 25mil, and the grid will update accordingly in the workspace.

Tips

  1. The X and Y grid values can be changed as required, and independently for the snap grid, by editing the grid through the Enter Grid (1..1000mil) dialog, accessed by using the Ctrl+G keyboard shortcut.
  2. Display of the grid (On/Off), as well as grid sizing (Size X:Y), can also be managed from the CAM Editor - Drawing Modes page of the Preferences dialog. The size drop-down field lists previously used grid values, or simply enter new sizing directly, as required.
  3. The snap grid is used when the Object Snap mode is set to Grid. The object snapping mode can be changed on the CAMtastic panel, or on the CAM Editor - Drawing Modes page of the Preferences dialog. With the mode set to Grid, the cursor automatically snaps to the grid, positioning the reference point of the object being placed onto the nearest grid location.


Applied Parameters: Size=50Mil

Summary

This command is used to set the X (horizontal) and Y (vertical) step values - for the Snap Grid - simultaneously to 50mil. These values together define the Snap Grid for manual movement and placement in the current document.

Access

This command is accessed from the CAMtastic Editor, by:

  • Using the G keyboard shortcut, then choosing the 50 Mil command from the pop-up menu.
  • Choosing the 50 Mil entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for both the X Grid and Y Grid properties of the Snap Grid will be set to 50mil, and the grid will update accordingly in the workspace.

Tips

  1. The X and Y grid values can be changed as required, and independently for the snap grid, by editing the grid through the Enter Grid (1..1000mil) dialog, accessed by using the Ctrl+G keyboard shortcut.
  2. Display of the grid (On/Off), as well as grid sizing (Size X:Y), can also be managed from the CAM Editor - Drawing Modes page of the Preferences dialog. The size drop-down field lists previously used grid values, or simply enter new sizing directly, as required.
  3. The snap grid is used when the Object Snap mode is set to Grid. The object snapping mode can be changed on the CAMtastic panel, or on the CAM Editor - Drawing Modes page of the Preferences dialog. With the mode set to Grid, the cursor automatically snaps to the grid, positioning the reference point of the object being placed onto the nearest grid location.


Applied Parameters: Size=100Mil

Summary

This command is used to set the X (horizontal) and Y (vertical) step values - for the Snap Grid - simultaneously to 100mil. These values together define the Snap Grid for manual movement and placement in the current document.

Access

This command is accessed from the CAMtastic Editor, by:

  • Using the G keyboard shortcut, then choosing the 100 Mil command from the pop-up menu.
  • Choosing the 100 Mil entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for both the X Grid and Y Grid properties of the Snap Grid will be set to 100mil, and the grid will update accordingly in the workspace.

Tips

  1. The X and Y grid values can be changed as required, and independently for the snap grid, by editing the grid through the Enter Grid (1..1000mil) dialog, accessed by using the Ctrl+G keyboard shortcut.
  2. Display of the grid (On/Off), as well as grid sizing (Size X:Y), can also be managed from the CAM Editor - Drawing Modes page of the Preferences dialog. The size drop-down field lists previously used grid values, or simply enter new sizing directly, as required.
  3. The snap grid is used when the Object Snap mode is set to Grid. The object snapping mode can be changed on the CAMtastic panel, or on the CAM Editor - Drawing Modes page of the Preferences dialog. With the mode set to Grid, the cursor automatically snaps to the grid, positioning the reference point of the object being placed onto the nearest grid location.


Applied Parameters: Size=200Mil

Summary

This command is used to set the X (horizontal) and Y (vertical) step values - for the Snap Grid - simultaneously to 200mil. These values together define the Snap Grid for manual movement and placement in the current document.

Access

This command is accessed from the CAMtastic Editor, by:

  • Using the G keyboard shortcut, then choosing the 200 Mil command from the pop-up menu.
  • Choosing the 200 Mil entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for both the X Grid and Y Grid properties of the Snap Grid will be set to 200mil, and the grid will update accordingly in the workspace.

Tips

  1. The X and Y grid values can be changed as required, and independently for the snap grid, by editing the grid through the Enter Grid (1..1000mil) dialog, accessed by using the Ctrl+G keyboard shortcut.
  2. Display of the grid (On/Off), as well as grid sizing (Size X:Y), can also be managed from the CAM Editor - Drawing Modes page of the Preferences dialog. The size drop-down field lists previously used grid values, or simply enter new sizing directly, as required.
  3. The snap grid is used when the Object Snap mode is set to Grid. The object snapping mode can be changed on the CAMtastic panel, or on the CAM Editor - Drawing Modes page of the Preferences dialog. With the mode set to Grid, the cursor automatically snaps to the grid, positioning the reference point of the object being placed onto the nearest grid location.


Applied Parameters: Size=500Mil

Summary

This command is used to set the X (horizontal) and Y (vertical) step values - for the Snap Grid - simultaneously to 500mil. These values together define the Snap Grid for manual movement and placement in the current document.

Access

This command is accessed from the CAMtastic Editor, by:

  • Using the G keyboard shortcut, then choosing the 500 Mil command from the pop-up menu.
  • Choosing the 500 Mil entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for both the X Grid and Y Grid properties of the Snap Grid will be set to 500mil, and the grid will update accordingly in the workspace.

Tips

  1. The X and Y grid values can be changed as required, and independently for the snap grid, by editing the grid through the Enter Grid (1..1000mil) dialog, accessed by using the Ctrl+G keyboard shortcut.
  2. Display of the grid (On/Off), as well as grid sizing (Size X:Y), can also be managed from the CAM Editor - Drawing Modes page of the Preferences dialog. The size drop-down field lists previously used grid values, or simply enter new sizing directly, as required.
  3. The snap grid is used when the Object Snap mode is set to Grid. The object snapping mode can be changed on the CAMtastic panel, or on the CAM Editor - Drawing Modes page of the Preferences dialog. With the mode set to Grid, the cursor automatically snaps to the grid, positioning the reference point of the object being placed onto the nearest grid location.


Applied Parameters: Size=0.025MM

Summary

This command is used to set the X (horizontal) and Y (vertical) step values - for the Snap Grid - simultaneously to 0.025mm. These values together define the Snap Grid for manual movement and placement in the current document.

Access

This command is accessed from the CAMtastic Editor, by:

  • Using the G keyboard shortcut, then choosing the 0.025 mm command from the pop-up menu.
  • Choosing the 0.025 mm entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for both the X Grid and Y Grid properties of the Snap Grid will be set to 0.025mm, and the grid will update accordingly in the workspace.

Tips

  1. The X and Y grid values can be changed as required, and independently for the snap grid, by editing the grid through the Enter Grid (1..1000mil) dialog, accessed by using the Ctrl+G keyboard shortcut.
  2. Display of the grid (On/Off), as well as grid sizing (Size X:Y), can also be managed from the CAM Editor - Drawing Modes page of the Preferences dialog. The size drop-down field lists previously used grid values, or simply enter new sizing directly, as required.
  3. The snap grid is used when the Object Snap mode is set to Grid. The object snapping mode can be changed on the CAMtastic panel, or on the CAM Editor - Drawing Modes page of the Preferences dialog. With the mode set to Grid, the cursor automatically snaps to the grid, positioning the reference point of the object being placed onto the nearest grid location.


Applied Parameters: Size=0.100MM

Summary

This command is used to set the X (horizontal) and Y (vertical) step values - for the Snap Grid - simultaneously to 0.100mm. These values together define the Snap Grid for manual movement and placement in the current document.

Access

This command is accessed from the CAMtastic Editor, by:

  • Using the G keyboard shortcut, then choosing the 0.100 mm command from the pop-up menu.
  • Choosing the 0.100 mm entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for both the X Grid and Y Grid properties of the Snap Grid will be set to 0.100mm, and the grid will update accordingly in the workspace.

Tips

  1. The X and Y grid values can be changed as required, and independently for the snap grid, by editing the grid through the Enter Grid (1..1000mil) dialog, accessed by using the Ctrl+G keyboard shortcut.
  2. Display of the grid (On/Off), as well as grid sizing (Size X:Y), can also be managed from the CAM Editor - Drawing Modes page of the Preferences dialog. The size drop-down field lists previously used grid values, or simply enter new sizing directly, as required.
  3. The snap grid is used when the Object Snap mode is set to Grid. The object snapping mode can be changed on the CAMtastic panel, or on the CAM Editor - Drawing Modes page of the Preferences dialog. With the mode set to Grid, the cursor automatically snaps to the grid, positioning the reference point of the object being placed onto the nearest grid location.


Applied Parameters: Size=0.250MM

Summary

This command is used to set the X (horizontal) and Y (vertical) step values - for the Snap Grid - simultaneously to 0.250mm. These values together define the Snap Grid for manual movement and placement in the current document.

Access

This command is accessed from the CAMtastic Editor, by:

  • Using the G keyboard shortcut, then choosing the 0.250 mm command from the pop-up menu.
  • Choosing the 0.250 mm entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for both the X Grid and Y Grid properties of the Snap Grid will be set to 0.250mm, and the grid will update accordingly in the workspace.

Tips

  1. The X and Y grid values can be changed as required, and independently for the snap grid, by editing the grid through the Enter Grid (1..1000mil) dialog, accessed by using the Ctrl+G keyboard shortcut.
  2. Display of the grid (On/Off), as well as grid sizing (Size X:Y), can also be managed from the CAM Editor - Drawing Modes page of the Preferences dialog. The size drop-down field lists previously used grid values, or simply enter new sizing directly, as required.
  3. The snap grid is used when the Object Snap mode is set to Grid. The object snapping mode can be changed on the CAMtastic panel, or on the CAM Editor - Drawing Modes page of the Preferences dialog. With the mode set to Grid, the cursor automatically snaps to the grid, positioning the reference point of the object being placed onto the nearest grid location.


Applied Parameters: Size=0.500MM

Summary

This command is used to set the X (horizontal) and Y (vertical) step values - for the Snap Grid - simultaneously to 0.500mm. These values together define the Snap Grid for manual movement and placement in the current document.

Access

This command is accessed from the CAMtastic Editor, by:

  • Using the G keyboard shortcut, then choosing the 0.500 mm command from the pop-up menu.
  • Choosing the 0.500 mm entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for both the X Grid and Y Grid properties of the Snap Grid will be set to 0.500mm, and the grid will update accordingly in the workspace.

Tips

  1. The X and Y grid values can be changed as required, and independently for the snap grid, by editing the grid through the Enter Grid (1..1000mil) dialog, accessed by using the Ctrl+G keyboard shortcut.
  2. Display of the grid (On/Off), as well as grid sizing (Size X:Y), can also be managed from the CAM Editor - Drawing Modes page of the Preferences dialog. The size drop-down field lists previously used grid values, or simply enter new sizing directly, as required.
  3. The snap grid is used when the Object Snap mode is set to Grid. The object snapping mode can be changed on the CAMtastic panel, or on the CAM Editor - Drawing Modes page of the Preferences dialog. With the mode set to Grid, the cursor automatically snaps to the grid, positioning the reference point of the object being placed onto the nearest grid location.


Applied Parameters: Size=1.000MM

Summary

This command is used to set the X (horizontal) and Y (vertical) step values - for the Snap Grid - simultaneously to 1.000mm. These values together define the Snap Grid for manual movement and placement in the current document.

Access

This command is accessed from the CAMtastic Editor, by:

  • Using the G keyboard shortcut, then choosing the 1.000 mm command from the pop-up menu.
  • Choosing the 1.000 mm entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for both the X Grid and Y Grid properties of the Snap Grid will be set to 1.000mm, and the grid will update accordingly in the workspace.

Tips

  1. The X and Y grid values can be changed as required, and independently for the snap grid, by editing the grid through the Enter Grid (1..1000mil) dialog, accessed by using the Ctrl+G keyboard shortcut.
  2. Display of the grid (On/Off), as well as grid sizing (Size X:Y), can also be managed from the CAM Editor - Drawing Modes page of the Preferences dialog. The size drop-down field lists previously used grid values, or simply enter new sizing directly, as required.
  3. The snap grid is used when the Object Snap mode is set to Grid. The object snapping mode can be changed on the CAMtastic panel, or on the CAM Editor - Drawing Modes page of the Preferences dialog. With the mode set to Grid, the cursor automatically snaps to the grid, positioning the reference point of the object being placed onto the nearest grid location.


Applied Parameters: Size=2.500MM

Summary

This command is used to set the X (horizontal) and Y (vertical) step values - for the Snap Grid - simultaneously to 2.500mm. These values together define the Snap Grid for manual movement and placement in the current document.

Access

This command is accessed from the CAMtastic Editor, by:

  • Using the G keyboard shortcut, then choosing the 2.500 mm command from the pop-up menu.
  • Choosing the 2.500 mm entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for both the X Grid and Y Grid properties of the Snap Grid will be set to 2.500mm, and the grid will update accordingly in the workspace.

Tips

  1. The X and Y grid values can be changed as required, and independently for the snap grid, by editing the grid through the Enter Grid (1..1000mil) dialog, accessed by using the Ctrl+G keyboard shortcut.
  2. Display of the grid (On/Off), as well as grid sizing (Size X:Y), can also be managed from the CAM Editor - Drawing Modes page of the Preferences dialog. The size drop-down field lists previously used grid values, or simply enter new sizing directly, as required.
  3. The snap grid is used when the Object Snap mode is set to Grid. The object snapping mode can be changed on the CAMtastic panel, or on the CAM Editor - Drawing Modes page of the Preferences dialog. With the mode set to Grid, the cursor automatically snaps to the grid, positioning the reference point of the object being placed onto the nearest grid location.


Applied Parameters: Size=5.000MM

Summary

This command is used to set the X (horizontal) and Y (vertical) step values - for the Snap Grid - simultaneously to 5.000mm. These values together define the Snap Grid for manual movement and placement in the current document.

Access

This command is accessed from the CAMtastic Editor, by:

  • Using the G keyboard shortcut, then choosing the 5.000 mm command from the pop-up menu.
  • Choosing the 5.000 mm entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for both the X Grid and Y Grid properties of the Snap Grid will be set to 5.000mm, and the grid will update accordingly in the workspace.

Tips

  1. The X and Y grid values can be changed as required, and independently for the snap grid, by editing the grid through the Enter Grid (1..1000mil) dialog, accessed by using the Ctrl+G keyboard shortcut.
  2. Display of the grid (On/Off), as well as grid sizing (Size X:Y), can also be managed from the CAM Editor - Drawing Modes page of the Preferences dialog. The size drop-down field lists previously used grid values, or simply enter new sizing directly, as required.
  3. The snap grid is used when the Object Snap mode is set to Grid. The object snapping mode can be changed on the CAMtastic panel, or on the CAM Editor - Drawing Modes page of the Preferences dialog. With the mode set to Grid, the cursor automatically snaps to the grid, positioning the reference point of the object being placed onto the nearest grid location.


Applied Parameters: Size=7.500MM

Summary

This command is used to set the X (horizontal) and Y (vertical) step values - for the Snap Grid - simultaneously to 7.500mm. These values together define the Snap Grid for manual movement and placement in the current document.

Access

This command is accessed from the CAMtastic Editor, by:

  • Using the G keyboard shortcut, then choosing the 7.500 mm command from the pop-up menu.
  • Choosing the 7.500 mm entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the value for both the X Grid and Y Grid properties of the Snap Grid will be set to 7.500mm, and the grid will update accordingly in the workspace.

Tips

  1. The X and Y grid values can be changed as required, and independently for the snap grid, by editing the grid through the Enter Grid (1..1000mil) dialog, accessed by using the Ctrl+G keyboard shortcut.
  2. Display of the grid (On/Off), as well as grid sizing (Size X:Y), can also be managed from the CAM Editor - Drawing Modes page of the Preferences dialog. The size drop-down field lists previously used grid values, or simply enter new sizing directly, as required.
  3. The snap grid is used when the Object Snap mode is set to Grid. The object snapping mode can be changed on the CAMtastic panel, or on the CAM Editor - Drawing Modes page of the Preferences dialog. With the mode set to Grid, the cursor automatically snaps to the grid, positioning the reference point of the object being placed onto the nearest grid location.


Applied Parameters: None

Summary

This command is used to set the X (horizontal) and Y (vertical) step values - for the Snap Grid - simultaneously to a chosen value. These values together define the Snap Grid for manual movement and placement in the current document.

Access

This command is accessed from the CAMtastic Editor, by:

  • Using the Ctrl+G keyboard shortcut.
  • Using the G keyboard shortcut, then choosing the Set Snap Grid command from the pop-up menu.
  • Choosing the Set Snap Grid entry on the Grids drop-down () of the Utilities toolbar.

Use

After launching the command, the Enter Grid (1..1000mil) dialog will appear. Enter the same, or different values to be used for the X Grid and Y Grid properties of the Snap Grid, and click OK - the grid will update accordingly in the workspace.

Tips

  1. Display of the grid (On/Off), as well as grid sizing (Size X:Y), can also be managed from the CAM Editor - Drawing Modes page of the Preferences dialog. The size drop-down field lists previously used grid values, or simply enter new sizing directly, as required.
  2. The snap grid is used when the Object Snap mode is set to Grid. The object snapping mode can be changed on the CAMtastic panel, or on the CAM Editor - Drawing Modes page of the Preferences dialog. With the mode set to Grid, the cursor automatically snaps to the grid, positioning the reference point of the object being placed onto the nearest grid location.

 

Found an issue with this document? Highlight the area, then use Ctrl+Enter to report it.

お問合せ

お近くの営業所にお問合せください。

You are reporting an issue with the following selected text
and/or image within the active document:
Altium Designer 無償評価版
Altium Designer 無償評価版
Altium Designerを使用していますか?

弊社の営業担当より詳細情報をご案内しますので、アルティウムジャパン までお問い合わせください。.
Copyright © 2019 Altium Limited

評価版ライセンスが必要な理由を下記から選択してください。

弊社の営業担当より詳細情報をご案内しますので、アルティウムジャパン までお問い合わせください。.
Copyright © 2019 Altium Limited

その場合、評価版ライセンスは不要です。

ボタンをクリックして、最新のAltium Designerインストーラをダウンロードしてください。

Altium Designerインストーラをダウンロードする

弊社の営業担当より詳細情報をご案内しますので、アルティウムジャパン までお問い合わせください。.
Copyright © 2019 Altium Limited

Altium Designerの新規ライセンスのお見積もりをご希望の場合、下記のフォームに入力してください。

プライバシーポリシーに同意の上、[ダウンロード]をクリックしてください。ご登録いただきましたメールアドレスにメールマガジンが送信されます。メール配信の停止は、メール内の​通知設定​​でお手続きいただけます。

Altium Designerサブスクリプションをご利用中の場合、評価版ライセンスは不要です。

お客様がAltium Designerサブスクリプションの有効なメンバーではない場合、下記のフォームに入力して無償評価版をダウンロードしてください。

プライバシーポリシーに同意の上、[ダウンロード]をクリックしてください。ご登録いただきましたメールアドレスにメールマガジンが送信されます。メール配信の停止は、メール内の​通知設定​​でお手続きいただけます。

Altium Designerを評価する理由を下記から選択してください。

弊社の営業担当より詳細情報をご案内しますので、アルティウムジャパン までお問い合わせください。.
Copyright © 2019 Altium Limited

無償評価版を使用するには、下記のフォームに入力してください。

プライバシーポリシーに同意の上、[ダウンロード]をクリックしてください。ご登録いただきましたメールアドレスにメールマガジンが送信されます。メール配信の停止は、メール内の​通知設定​​でお手続きいただけます。

Great News!

Valid students can get their very own 6-month Altium Designer Student License for FREE! Just fill out the form below to request your Student License today.

プライバシーポリシーに同意の上、[ダウンロード]をクリックしてください。ご登録いただきましたメールアドレスにメールマガジンが送信されます。メール配信の停止は、メール内の​通知設定​​でお手続きいただけます。

その場合、Altium Designerビューワーの無償ライセンス(有効期間6か月)をダウンロードできます。

下記のフォームに入力してライセンスをリクエストしてください。

プライバシーポリシーに同意の上、[ダウンロード]をクリックしてください。ご登録いただきましたメールアドレスにメールマガジンが送信されます。メール配信の停止は、メール内の​通知設定​​でお手続きいただけます。

素晴らしいですね。アルティウムではモノづくりに最適なプログラムを提供しています。

Upverterは、コミュニティ主導型の無償プラットフォームで、お客様のような作り手の要求に合わせて設計されています。

試してみる場合、こちらをクリック してください。

弊社の営業担当より詳細情報をご案内しますので、アルティウムジャパン までお問い合わせください。.
Copyright © 2019 Altium Limited

その場合、Altium Designerビューワーの無償ライセンス(有効期間6か月)をダウンロードできます。

下記のフォームに入力してライセンスをリクエストしてください。

プライバシーポリシーに同意の上、[ダウンロード]をクリックしてください。ご登録いただきましたメールアドレスにメールマガジンが送信されます。メール配信の停止は、メール内の​通知設定​​でお手続きいただけます。