Altium NEXUS Documentation

ResetCamera

Modified by Susan Riege on Feb 9, 2021

Parent page: PCB Commands

The following pre-packaged resources, derived from this base command, are available:


Applied Parameters: None

Summary

This command is used to change the view of the board (or component) in 3D so that you are looking straight down from above (perpendicular), with zero rotation.

Access

This command is accessed from the PCB Editor and the PCB Library Editor in 3D Layout Mode by:

  • Choosing the View » 3D View Control » Zero Rotation command from the main menus.
  • Using the 0 keyboard shortcut.
The current viewing mode for the PCB document can be changed using the corresponding commands from the main View menu. To switch to 3D Layout Mode, use the command of the same name, or use the 3 keyboard shortcut.

Use

After launching the command, the 3D view will be changed, if necessary, so that you are viewing the board from above and with no rotation.

Tips

  1. In addition, you can use the applicable drop-down field on the PCB Standard toolbar (PCB Editor) or the PCB Lib Standard toolbar (PCB Library Editor) to quickly choose from a set of predefined 3D views when viewing your board (or library components) in 3D.
  2. The rotation angle step is set to 30° by default, and the pan distance step is set to 500mils (12.7mm) by default. These settings can be accessed and edited in the Other section of the PCB Editor - General page of the Preferences dialog.


Applied Parameters: To=Rotate90

Summary

This command is used to change the view of the board (or component) in 3D so that you are looking straight down from above (perpendicular) with 90 degrees (clockwise) rotation in the X-plane.

Access

This command is accessed from the PCB Editor and the PCB Library Editor in 3D Layout Mode by:

  • Choosing the View » 3D View Control » 90 Degree Rotation command from the main menus.
  • Using the 9 keyboard shortcut.
The current viewing mode for the PCB document can be changed using the corresponding commands from the main View menu. To switch to 3D Layout Mode, use the command of the same name, or use the 3 keyboard shortcut.

Use

After launching the command, the 3D view will be changed, if necessary, so that you are viewing the board from above and with 90 degrees (clockwise) rotation in the X-plane.

Tips

  1. In addition, you can use the applicable drop-down field on the PCB Standard toolbar (PCB Editor) or the PCB Lib Standard toolbar (PCB Library Editor) to quickly choose from a set of predefined 3D views when viewing your board (or library components) in 3D.
  2. The rotation angle step is set to 30° by default, and the pan distance step is set to 500mils (12.7mm) by default. These settings can be accessed and edited in the Other section of the PCB Editor - General page of the Preferences dialog.


Applied Parameters: To=RotateOrtho

Summary

This command is used to change the view of the board (or component) in 3D so that you are looking at the board from an orthogonal perspective.

Access

This command is accessed from the PCB Editor and the PCB Library Editor in 3D Layout Mode by:

  • Choosing the View » 3D View Control » Orthogonal Rotation command from the main menus.
  • Using the 8 keyboard shortcut.
The current viewing mode for the PCB document can be changed using the corresponding commands from the main View menu. To switch to 3D Layout Mode, use the command of the same name, or use the 3 keyboard shortcut.

Use

After launching the command, the 3D view will be changed, if necessary, so that you are viewing the board from an orthogonal perspective (looking from above, and from the left).

Tips

  1. In addition, you can use the applicable drop-down field on the PCB Standard toolbar (PCB Editor) or the PCB Lib Standard toolbar (PCB Library Editor), to quickly choose from a set of predefined 3D views when viewing your board (or library components) in 3D.
  2. The rotation angle step is set to 30° by default, and the pan distance step is set to 500mils (12.7mm) by default. These settings can be accessed and edited in the Other section of the PCB Editor - General page of the Preferences dialog.


Applied Parameters: To=RotateOrtho

Summary

This command is used to change the view of the board (or component) in 3D so that you are looking at the board from an isometric perspective.

Access

This command is accessed from the PCB Editor and the PCB Library Editor in 3D Layout Mode by:

  • Choosing the View » 3D View Control » Isometric View command from the main menus.
  • Using the Num0 keyboard shortcut.
The current viewing mode for the PCB document can be changed using the corresponding commands from the main View menu. To switch to 3D Layout Mode, use the command of the same name, or use the 3 keyboard shortcut.

Use

After launching the command, the 3D view will be changed, if necessary, so that you are viewing the board from an isometric perspective.

Tips

  1. In addition, you can use the applicable drop-down field on the PCB Standard toolbar (PCB Editor) or the PCB Lib Standard toolbar (PCB Library Editor), to quickly choose from a set of predefined 3D views when viewing your board (or library components) in 3D.


Applied Parameters: To=Top

Summary

This command is used to change the view of the board (or component) in 3D so that you are looking at the board's entire top side.

Access

This command is accessed from the PCB Editor and the PCB Library Editor in 3D Layout Mode by:

  • Choosing the View » 3D View Control » Top Side command from the main menus.
  • Using the Num1 keyboard shortcut.
The current viewing mode for the PCB document can be changed using the corresponding commands from the main View menu. To switch to 3D Layout Mode, use the command of the same name, or use the 3 keyboard shortcut.

Use

After launching the command, the 3D view will be changed, if necessary, so that you are viewing the entire board from the top.

Tips

  1. In addition, you can use the applicable drop-down field on the PCB Standard toolbar (PCB Editor) or the PCB Lib Standard toolbar (PCB Library Editor), to quickly choose from a set of predefined 3D views when viewing your board (or library components) in 3D.


Applied Parameters: To=Bottom

Summary

This command is used to change the view of the board (or component) in 3D so that you are looking at the board's entire bottom side.

Access

This command is accessed from the PCB Editor and the PCB Library Editor in 3D Layout Mode by:

  • Choosing the View » 3D View Control » Bottom Side command from the main menus.
  • Using the Ctrl+Num1 keyboard shortcut.
The current viewing mode for the PCB document can be changed using the corresponding commands from the main View menu. To switch to 3D Layout Mode, use the command of the same name, or use the 3 keyboard shortcut.

Use

After launching the command, the 3D view will be changed, if necessary, so that you are viewing the entire board from the bottom.

Tips

  1. In addition, you can use the applicable drop-down field on the PCB Standard toolbar (PCB Editor) or the PCB Lib Standard toolbar (PCB Library Editor), to quickly choose from a set of predefined 3D views when viewing your board (or library components) in 3D.


Applied Parameters: To=Front

Summary

This command is used to change the view of the board (or component) in 3D so that you are looking directly at its front side.

Access

This command is accessed from the PCB Editor and the PCB Library Editor in 3D Layout Mode by:

  • Choosing the View » 3D View Control » Front Side command from the main menus.
  • Using the Num7 keyboard shortcut.
The current viewing mode for the PCB document can be changed using the corresponding commands from the main View menu. To switch to 3D Layout Mode, use the command of the same name, or use the 3 keyboard shortcut.

Use

After launching the command, the 3D view will be changed, if necessary, so that you are viewing the front side of the board.

Tips

  1. In addition, you can use the applicable drop-down field on the PCB Standard toolbar (PCB Editor) or the PCB Lib Standard toolbar (PCB Library Editor), to quickly choose from a set of predefined 3D views when viewing your board (or library components) in 3D.


Applied Parameters: To=Back

Summary

This command is used to change the view of the board (or component) in 3D so that you are looking directly at its back side.

Access

This command is accessed from the PCB Editor and the PCB Library Editor in 3D Layout Mode by:

  • Choosing the View » 3D View Control » Back Side command from the main menus.
  • Using the Ctrl+Num7 keyboard shortcut.
The current viewing mode for the PCB document can be changed using the corresponding commands from the main View menu. To switch to 3D Layout Mode, use the command of the same name, or use the 3 keyboard shortcut.

Use

After launching the command, the 3D view will be changed, if necessary, so that you are viewing the back side of the board.

Tips

  1. In addition, you can use the applicable drop-down field on the PCB Standard toolbar (PCB Editor) or the PCB Lib Standard toolbar (PCB Library Editor) to quickly choose from a set of predefined 3D views when viewing your board (or library components) in 3D.


Applied Parameters: To=Left

Summary

This command is used to change the view of the board (or component) in 3D so that you are looking directly at its left edge.

Access

This command is accessed from the PCB Editor and the PCB Library Editor in 3D Layout Mode by:

  • Choosing the View » 3D View Control » Left Edge command from the main menus.
  • Using the Num3 keyboard shortcut.
The current viewing mode for the PCB document can be changed using the corresponding commands from the main View menu. To switch to 3D Layout Mode, use the command of the same name, or use the 3 keyboard shortcut.

Use

After launching the command, the 3D view will be changed, if necessary, so that you are viewing the left edge of the board.

Tips

  1. In addition, you can use the applicable drop-down field on the PCB Standard toolbar (PCB Editor) or the PCB Lib Standard toolbar (PCB Library Editor) to quickly choose from a set of predefined 3D views when viewing your board (or library components) in 3D.


Applied Parameters: To=Right

Summary

This command is used to change the view of the board (or component) in 3D so that you are looking directly at its right edge.

Access

This command is accessed from the PCB Editor and the PCB Library Editor in 3D Layout Mode by:

  • Choosing the View » 3D View Control » Right Edge command from the main menus.
  • Using the Ctrl+Num3 keyboard shortcut.
The current viewing mode for the PCB document can be changed using the corresponding commands from the main View menu. To switch to 3D Layout Mode, use the command of the same name, or use the 3 keyboard shortcut.

Use

After launching the command, the 3D view will be changed, if necessary, so that you are viewing the right edge of the board.

Tips

  1. In addition, you can use the applicable drop-down field on the PCB Standard toolbar (PCB Editor) or the PCB Lib Standard toolbar (PCB Library Editor) to quickly choose from a set of predefined 3D views when viewing your board (or library components) in 3D.


Applied Parameters: To=ISOMETRIC

Summary

This command is used to change the view of the board (or component) in 3D so that you are looking at a flipped isometric view.

Access

This command is accessed from the PCB Editor and the PCB Library Editor in 3D Layout Mode by:

  • Choosing the View » 3D View Control » Flipped Isometric View command from the main menus.
  • Using the Ctrl+Num0 keyboard shortcut.
The current viewing mode for the PCB document can be changed using the corresponding commands from the main View menu. To switch to 3D Layout Mode, use the command of the same name, or use the 3 keyboard shortcut.

Use

After launching the command, the 3D view will be changed so that you are viewing the flipped isometric view.

Tip

In addition, you can use the applicable drop-down field on the PCB Standard toolbar (PCB Editor) or the PCB Lib Standard toolbar (PCB Library Editor) to quickly choose from a set of predefined 3D views when viewing your board (or library components) in 3D.

Found an issue with this document? Highlight the area, then use Ctrl+Enter to report it.

お問合せ

お近くの営業所にお問合せください。

We're sorry to hear the article wasn't helpful to you.
Could you take a moment to tell us why?
200 characters remaining
You are reporting an issue with the following selected text
and/or image within the active document:
Altium Designer 無償評価版
Altium Designer 無償評価版
Altium Designerを使用していますか?

弊社の営業担当より詳細情報をご案内しますので、アルティウムジャパン までお問い合わせください。.
Copyright © 2019 Altium Limited

評価版ライセンスが必要な理由を下記から選択してください。

弊社の営業担当より詳細情報をご案内しますので、アルティウムジャパン までお問い合わせください。.
Copyright © 2019 Altium Limited

その場合、評価版ライセンスは不要です。

ボタンをクリックして、最新のAltium Designerインストーラをダウンロードしてください。

Altium Designerインストーラをダウンロードする

弊社の営業担当より詳細情報をご案内しますので、アルティウムジャパン までお問い合わせください。.
Copyright © 2019 Altium Limited

Altium Designerの新規ライセンスのお見積もりをご希望の場合、下記のフォームに入力してください。

プライバシーポリシーに同意の上、[ダウンロード]をクリックしてください。ご登録いただきましたメールアドレスにメールマガジンが送信されます。メール配信の停止は、メール内の​通知設定​​でお手続きいただけます。

Altium Designerサブスクリプションをご利用中の場合、評価版ライセンスは不要です。

お客様がAltium Designerサブスクリプションの有効なメンバーではない場合、下記のフォームに入力して無償評価版をダウンロードしてください。

プライバシーポリシーに同意の上、[ダウンロード]をクリックしてください。ご登録いただきましたメールアドレスにメールマガジンが送信されます。メール配信の停止は、メール内の​通知設定​​でお手続きいただけます。

Altium Designerを評価する理由を下記から選択してください。

弊社の営業担当より詳細情報をご案内しますので、アルティウムジャパン までお問い合わせください。.
Copyright © 2019 Altium Limited

無償評価版を使用するには、下記のフォームに入力してください。

プライバシーポリシーに同意の上、[ダウンロード]をクリックしてください。ご登録いただきましたメールアドレスにメールマガジンが送信されます。メール配信の停止は、メール内の​通知設定​​でお手続きいただけます。

Great News!

Valid students can get their very own 6-month Altium Designer Student License for FREE! Just fill out the form below to request your Student License today.

プライバシーポリシーに同意の上、[ダウンロード]をクリックしてください。ご登録いただきましたメールアドレスにメールマガジンが送信されます。メール配信の停止は、メール内の​通知設定​​でお手続きいただけます。

その場合、Altium Designerビューワーの無償ライセンス(有効期間6か月)をダウンロードできます。

下記のフォームに入力してライセンスをリクエストしてください。

プライバシーポリシーに同意の上、[ダウンロード]をクリックしてください。ご登録いただきましたメールアドレスにメールマガジンが送信されます。メール配信の停止は、メール内の​通知設定​​でお手続きいただけます。

素晴らしいですね。アルティウムではモノづくりに最適なプログラムを提供しています。

Upverterは、コミュニティ主導型の無償プラットフォームで、お客様のような作り手の要求に合わせて設計されています。

試してみる場合、こちらをクリック してください。

弊社の営業担当より詳細情報をご案内しますので、アルティウムジャパン までお問い合わせください。.
Copyright © 2019 Altium Limited

その場合、Altium Designerビューワーの無償ライセンス(有効期間6か月)をダウンロードできます。

下記のフォームに入力してライセンスをリクエストしてください。

プライバシーポリシーに同意の上、[ダウンロード]をクリックしてください。ご登録いただきましたメールアドレスにメールマガジンが送信されます。メール配信の停止は、メール内の​通知設定​​でお手続きいただけます。