Altium Designer Documentation

ToggleComponentFittedInPhysicalSheet

Created: August 4, 2017 | Updated: August 4, 2017

Parent page: Schematic Commands

The following pre-packaged resources, derived from this base command, are available:


Applied Parameters: None

Summary

This command is used to toggle the fitted/not fitted state of one or more components, on the active physical schematic sheet, and for the active Design Variant.

Access

This command is accessed from the Schematic Editor. First ensure that the required variant for the design is chosen, from the Variants folder for the project, in the Projects panel.

When variants have been defined for a project, a Variants folder will be added to the Projects panel for that project. The folder contains entries for the base design ([No Variations]), as well as all variants you have defined. The current variant is displayed in bold, white text. To make any listed variant the current variant, you can either double-click the desired variant in the panel, or right-click the desired variant and choose Set as current.

With the applicable physical sheet for the circuit made active - the relevant Compiled View tab, and not the Editor tab - click the  button on the Active Bar.

Use

After launching the command, the cursor will change to a cross-hair, and you will enter toggle mode. Simply click on a placed component to toggle its state from Fitted to Not Fitted, or vice-versa. When Not Fitted, the component will appear with overlay graphics, as defined in the Variant Options dialog (for example, a red cross).

Continue toggling the Fitted/Not Fitted state of further components on the sheet, or right-click, or press Esc, to exit toggle mode.

Tips

  1. To examine design variations, you must compile the design and then switch to the compiled tab of the schematic.
  2. Before you can create a variant, you first create the original design, which is referred to as the base design. Working from the base design, you then go through a process of configuring the components to be: Fitted; Fitted with varied parameters; Not Fitted; or to use an Alternate Part. Management of design variants is performed primarily within the Variant Management dialog.


Applied Parameters: ContextSensitive=True

Summary

This command is used to quickly toggle the fitted/not fitted state of the component under the cursor, on the active physical schematic sheet, and for the active Design Variant.

Access

This command is accessed from the Schematic Editor. First ensure that the required variant for the design is chosen, from the Variants folder for the project, in the Projects panel.

When variants have been defined for a project, a Variants folder will be added to the Projects panel for that project. The folder contains entries for the base design ([No Variations]), as well as all variants you have defined. The current variant is displayed in bold, white text. To make any listed variant the current variant, you can either double-click the desired variant in the panel, or right-click the desired variant and choose Set as current.

With the applicable physical sheet for the circuit made active - the relevant Compiled View tab, and not the Editor tab -  right-click over the required placed component and choose the Part Actions » Toggle Fitted/Not Fitted command from the context menu.

Use

After launching the command, the component under the cursor will have its state changed from Fitted to Not Fitted, or vice-versa. When Not Fitted, the component will appear with overlay graphics, as defined in the Variant Options dialog (for example, a red cross).

Tips

  1. To examine design variations, you must compile the design and then switch to the compiled tab of the schematic.
  2. Before you can create a variant, you first create the original design, which is referred to as the base design. Working from the base design, you then go through a process of configuring the components to be: Fitted; Fitted with varied parameters; Not Fitted; or to use an Alternate Part. Management of design variants is performed primarily within the Variant Management dialog.

 

Found an issue with this document? Highlight the area, then use Ctrl+Enter to report it.

联系我们

联系原厂或当地办公室

We're sorry to hear the article wasn't helpful to you.
Could you take a moment to tell us why?
200 characters remaining
You are reporting an issue with the following selected text
and/or image within the active document:
Altium Designer 免费试用
Altium Designer Free Trial
我们开始吧!首先,您或者您的公司已经在使用Altium Designer了吗?

如果您有任何需求,请点击这里联系获取当地办公室销售代表联系方式。.
Copyright © 2019 Altium Limited

既然您在使用Altium Designer,为何仍需要试用?

如果您有任何需求,请点击这里联系获取当地办公室销售代表联系方式。.
Copyright © 2019 Altium Limited

好的,实际上您无需下载一个试用版本。

点击下方按钮下载最新版本的Altium Designer安装包

下载Altium Designer 安装包

如果您有任何需求,请点击这里联系获取当地办公室销售代表联系方式。.
Copyright © 2019 Altium Limited

填写下方表格,获取Altium Designer最新报价。

点击[获取免费试用],并同意我们的隐私政策。您会接收到来自Altium的资讯,并允许其改变您的通知首选项。

如果您是Altium维保期内客户,您不需要下载试用版本。

如果您不是Altium维保客户,请填写下方表格免费试用。

点击[获取免费试用],并同意我们的隐私政策。您会接收到来自Altium的资讯,并允许其改变您的通知首选项。

您为何想要试用Altium Designer?

如果您有任何需求,请点击这里联系获取当地办公室销售代表联系方式。.
Copyright © 2019 Altium Limited

那您来对地方了!请填写下方表格申请试用吧。

点击[获取免费试用],并同意我们的隐私政策。您会接收到来自Altium的资讯,并允许其改变您的通知首选项。

Great News!

Valid students can get their very own 6-month Altium Designer Student License for FREE! Just fill out the form below to request your Student License today.

点击[获取免费试用],并同意我们的隐私政策。您会接收到来自Altium的资讯,并允许其改变您的通知首选项。

好的,您可以下载免费的Altium Designer Viewer查看文档,有效期6个月。

请填写下方表格申请。

点击[获取免费试用],并同意我们的隐私政策。您会接收到来自Altium的资讯,并允许其改变您的通知首选项。

好棒!创作是一件超酷的事情,我们可以为您提供完美的设计软件。

Upverter是一个社区导向的交流平台,专为您这样的创客量身定做。

点击这里看看吧!

如果您有任何需求,请点击这里联系获取当地办公室销售代表联系方式。.
Copyright © 2019 Altium Limited

好的,您可以下载免费的Altium Designer Viewer查看文档,有效期6个月。

请填写下方表格申请。

点击[获取免费试用],并同意我们的隐私政策。您会接收到来自Altium的资讯,并允许其改变您的通知首选项。