PCB Library Footprint

This document is no longer available beyond version 22. Information can now be found here: Footprint Properties for version 24

Applies to Altium Designer version: 21

Two iterations of the PCB Library Footprint dialog: on the left, the dialog as it appears when access from a file-based PCB Library document; on the right, the dialog as it appears when defining a footprint from a Workspace.
Two iterations of the PCB Library Footprint dialog: on the left, the dialog as it appears when access from a file-based PCB Library document; on the right, the dialog as it appears when defining a footprint from a Workspace.

Summary

This dialog allows you to specify various properties for the active footprint in the current PCB Library document.

Access

The dialog is accessed from the PCB Library Editor in the following ways:

  • With the desired footprint active in the main design window, use the Tools » Footprint Properties command from the main menus.
  • Double-click a footprint in the Footprints region of the PCB Library panel.

Options/Controls

  • Name – use this field to specify the footprint's name.
  • Description – use this field to add a meaningful description for the footprint.
  • Type – use this field to determine the type of footprint. Choose from the following types:
    • Standard – standard electrical footprint loaded onto the board; always synchronized, always in the BOM.
    • Mechanical – non-electrical footprint, e.g., heat sink or mounting bracket. Synchronized if it exists on both schematic and PCB documents and always included in the BOM.
    • Graphical – non-electrical footprint used for a company logo, title block, etc; never synchronized and not included in the BOM.
    • Net Tie (In BOM) – for shorting two (or more) nets together in the routing. Typically used if a jumper type footprint needs to be fitted and also provide shorting in the same location; always synchronized and included in the BOM.
    • Net Tie – as above but designed so you could not tell a footprint existed at the location where the shorting is to occur; always synchronized but not included in the BOM. When placing components of this type, use the Verify Shorting Copper option in the Design Rule Checker dialog (when performing a DRC in the PCB) to verify the short (i.e. that no unconnected copper exists in the footprint).
    • Standard (No BOM) – standard electrical footprint loaded onto board; always synchronized, not included in the BOM.
    • Jumper – used to represent a wire link, typically used on a single-sided board. On the schematic, Jumper-type footprints do not need to be wired in. They are only included to ensure that the Jumpers get included in the BOM. On the PCB, set the jumper pads to share the same non-zero JumperID value; the software recognizes this state, adds a symbolic link between the jumper pads to represent the wire link, and factors the link into design rule checks.
    The Type setting allows you to set the type for a footprint that is placed directly from the PCB Library onto the PCB design document. However, if the footprint has been placed on the schematic side and brought across to the PCB through the synchronization process, then the Type setting defined for that footprint – on the schematic side – will always take precedence.
  • Height – use this field to specify a height for the footprint. This value is used by the Height design rule (part of the Placement category of rules).
  • Area – use this field to modify the area calculation of the component associated with the footprint.

The following options and controls are available only when defining a footprint from a Workspace:

  • Item Revision – the Item-Revision ID used for the footprint model being defined in the Workspace.
    • Choose – click to access the Choose Item dialog (an incarnation of the Explorer panel), which allows you to target an existing revision in the actively connected Workspace.
  • Source – provides the name of the Workspace in which the footprint model resides.
    • Show in Explorer – click to open the Explorer panel showing the footprint.
  • Revision Details – displays any defined description of the footprint revision.
  • Revision State – displays the current lifecycle state of the footprint revision.

    When connected to an Altium 365 Workspace, note that configuration and use of lifecycle definitions is not supported with the Standard Subscription Plan. As such, the Revision State will not be available with this level of access to Altium 365.
Note

The features available depend on your level of Altium Designer Software Subscription.