Altium NEXUS Documentation

PlaceBendingLine

Modified by Susan Riege on Mar 18, 2021

Parent page: PCB Commands

The following pre-packaged resource, derived from this base command, is available:

Applied Parameters:  BoardPlanningMode=True

Summary

This command is used to place a Bending Line across an existing board region within the current design. A bending line is a drawn PCB object that defines how a flexible board should be bent. Bending lines can be placed across a Board Region that has been assigned a Layer Stack with the Flex option enabled – that is, the particular board region has been configured as flexible.

A bending line defines where on the surface of the flex region the bend is to take place. It also defines the angle and radius of the bend and the width of the strip of board surface that is being bent. When the PCB editor is in 3D Layout mode, the bends can be displayed in their progressively folded state, providing a real-world look at the rigid-flex design.

For detailed information about this object type, see Bending Line.

Access

This command can be accessed from the PCB Editor when configured in Board Planning Mode by choosing the Place » Define Bending Line command from the main menus, right-clicking in the design space then selecting Place » Define Bending Line, or select  from the Active Bar.

The current viewing mode for the PCB document can be changed using the corresponding commands from the main View menu. To switch to Board Planning Mode, use the command of the same name or use the 1 keyboard shortcut.

Use

After launching the command, the cursor will change to a cross-hair and you will enter bending line placement mode. Placement is made by performing the following sequence of actions:

  1. Click, or press Enter, inside the board region where the bending line is to be placed. One end of the line will attach to the edge of the region closest to the click location, the other end will attach to the directly opposite edge.  
  2. Move the cursor to position the other end of the bending line, then click or press Enter to place it. The bending line will remain yellow if the location is valid.
  3. Continue placing further bending lines, or right-click, or press Esc, to exit placement mode.

Tip

When a board region is set to use a Flex layer stack, a bending line is automatically added, vertically down its geometric center. Remove, or reposition and configure this bending line as required.

Found an issue with this document? Highlight the area, then use Ctrl+Enter to report it.

Contact Us

Contact our corporate or local offices directly.

We're sorry to hear the article wasn't helpful to you.
Could you take a moment to tell us why?
You are reporting an issue with the following selected text
and/or image within the active document:
ALTIUM DESIGNER FREE TRIAL
Altium Designer Free Trial
Let’s get started. First off, are you or your organization already using Altium Designer?

If would like to speak with a representative, please contact your local Altium office.
Copyright © 2019 Altium Limited

In that case, why do you need an evaluation license?

If would like to speak with a representative, please contact your local Altium office.
Copyright © 2019 Altium Limited

Got it. You actually don’t need an evaluation license for that.

Click the button below to download the latest Altium Designer installer.

Download Altium Designer Installer

If would like to speak with a representative, please contact your local Altium office.
Copyright © 2019 Altium Limited

Please fill out the form below to get a quote for a new seat of Altium Designer.

By clicking “Get Your Free Trial”, you are agreeing to our Privacy Policy.
You may receive communications from Altium and can change your notification preferences at any time.

If you are on Altium Subscription, you don’t need an evaluation license.

If you are not an active Altium Subscription member, please fill out the form below to get your free trial.

By clicking “Get Your Free Trial”, you are agreeing to our Privacy Policy.
You may receive communications from Altium and can change your notification preferences at any time.

Why are you looking to evaluate Altium Designer?

If would like to speak with a representative, please contact your local Altium office.
Copyright © 2019 Altium Limited

You came to the right place! Please fill out the form below to get your free trial started.

By clicking “Get Your Free Trial”, you are agreeing to our Privacy Policy.
You may receive communications from Altium and can change your notification preferences at any time.

Great News!

Valid students can get their very own 6-month Altium Designer Student License for FREE! Just fill out the form below to request your Student License today.

By clicking “Get Your Free Trial”, you are agreeing to our Privacy Policy.
You may receive communications from Altium and can change your notification preferences at any time.

Got it. You can download a free Altium Designer Viewer license which is valid for a 6 months.

Please fill out the form below to request one.

By clicking “Get Your Free Trial”, you are agreeing to our Privacy Policy.
You may receive communications from Altium and can change your notification preferences at any time.

That’s great! Making things is awesome. We have the perfect program for you.

Upverter is a free community-driven platform designed specifically to meet the needs of makers like you.

Click here to give it a try!

If would like to speak with a representative, please contact your local Altium office.
Copyright © 2019 Altium Limited

Got it. You can download a free Altium Designer Viewer license which is valid for a 6 months.

Please fill out the form below to request one.

By clicking “Get Your Free Trial”, you are agreeing to our Privacy Policy.
You may receive communications from Altium and can change your notification preferences at any time.