Altium Designer Documentation

Pad

Modified by Phil Loughhead on Jun 19, 2017
此文档页面引用了不再受支持的产品 Altium Vault, Altium Vault 及其组件管理功能已迁移到 Altium Concord Pro


The Pad dialog.

Summary

This dialog allows the designer to specify the properties of a Pad object. A pad is used to create the electrical connection and mounting point for a component pin. Pads, along with other objects such as lines, are placed in the PCB Library editor to create a footprint for the component to be mounted on. Pads can be single layer or multi-layer (exist on every signal layer). Pads can have a hole, which can be round, square or a slot. The hole is centered by default, but can also be offset if required.

Access

This dialog can be accessed during placement by pressing the Tab key.

After placement, the dialog can be accessed in the following ways:

  • Double-click on a placed object.
  • Place the cursor over the object, right-click and choose Properties from the context menu.

Options/Controls

To toggle the units of measurement used in the open dialog between metric (mm) and imperial (mil), press the Ctrl+Q shortcut.

Pad Template

  • Template - Select a Pad template from the dropdown.
  • Library - Displays which library the Pad template is linked to and includes the option to unlink the template from said library.

Location

  • X - The current X position of the center of the pad, relative to the current origin. Edit the value to change the position of the pad relative to the origin.
  • Y - The current Y position of the center of the pad, relative to the current origin. Edit the value to change the position of the pad relative to the origin.
  • Rotation - The current pad rotation in degrees, edit to change the rotation of the pad. Minimum angular resolution is 0.001°.

Values can be defined in either mm or mil units. When entering a value in units other than the current units, add the mm or mil suffix to the value.

Hole Information

  • Hole Size - The current hole size for the pad. The value specifies the diameter of the hole (in mils or mm) to be drilled in the pad during fabrication. For a single-layer pad (such as an SMD pad or edge connector), this is automatically set to zero. The hole size can be set from 0 to 1000mil, and can be set larger than the pad area to define copper free mechanical holes. Edit the value in this field to change the pad hole size. Values can be entered in either mm or mil units.
  • Tolerance - Setting the hole tolerance attribute can help determine the fits and limits of your board. Specify the Minimum (-) and Maximum (+) hole tolerance for the design.

Choose one of the following options to specify the shape of the hole:

  • Round - specifies a round hole shape (default) for the pad.
  • Square - specifies a square (punched) hole shape for the pad.
  • Slot - specifies a round ended slotted hole shape for the pad.
     
  • Plated - This option determines whether or not the pad has a plated hole. If both plated and non-plated pads exist in a design, the non-plated holes will be set to use different tools from the plated holes in the NC drill files.

Separate drill files (NC Drill Excellon format 2) are generated for each hole kind (Round, Square and Slot) as well as for plated and non-plated holes (as defined by the Plated checkbox). This means there can be up to six different drill files generated.

Properties

  • Designator - The current pad designator. If the pad is part of a component, the designator is usually set to the corresponding component pin number. The designator can be up to 20 characters in length and cannot include any spaces. Free pads can include a designator, or the field can be left empty. If the designator begins or ends with a number, the number will auto-increment when placing a series of pads sequentially. Edit the value in this field to change the pad designator. Note that multiple pads within the same component footprint can share the same designator, if required.
  • Layer - The layer the pad is currently assigned to. Pads can be assigned to any available layer, Set the Layer to Multi-Layer to define a pad shape on all signal layers.
  • Net - The net that the pad is currently assigned to. Change the net assignment by clicking in the field and choosing a net from the drop down list. Select No Net to specify that the pad is not connected to any net. The Net property of a primitive is used by the Design Rule Checker to determine if a PCB object is legally placed.
  • Jumper ID - Set the Jumper ID to a non-zero value (range of 1-1000) to indicate that this pad is part of a jumper component footprint. Jumper components can be used on a single-sided PCB when there will be a wire link that physically connects the pads together, rather than using tracks to create the connection. The Jumper ID value tells the software which pads to treat as 'connected'. A jumper connection can only be created between the pads within the same component footprint, they must have the same Jumper ID value, and must also be assigned the same net. The component must also have its Type set to Jumper. When these conditions are met, a jumper connection is shown as a curved connection line in the PCB Editor.
  • Locked - Enable to protect the pad from being edited graphically. Lock a pad whose position or size is critical. If you try to edit a primitive that is locked, you will be informed that the primitive is locked and asked if you wish to proceed with the action. If this option is unchecked, the primitive can be freely edited without confirmation. Note that the Locked checkbox has no effect on a pad that belongs to a component, if the component is not locked the pads will move when the component is moved. In this situation, lock the component to prevent accidental movement.

Testpoint Settings

Use the Testpoint Settings to define this pad as a testpoint for Fabrication and/or Assembly testpoint file generation. A testpoint is a location where a test probe can make contact with the PCB to check for correct function of the board. Any pad or via can be nominated as a testpoint, when this is done the component that the pad or via belongs to, automatically gets locked.

  • Top - Enable this option for this pad to be defined as a top layer testpoint.
  • Bottom - Enable this option for this pad to be defined as a bottom layer testpoint.

Size and Shape

The copper area (land area) of the pad is defined by the X and Y size, and the Shape setting.

  • Simple - A simple pad is one whose size and shape is identical on all layers.
  • Top-Middle-Bottom - A Top-Middle-Bottom layered pad supports defining different X & Y sizes and shape for the Top layer, for all mid signal layers, and for the Bottom layer, separately.
    • X-Size - The current X (horizontal) size of the pad, enter a value from 1 to 10000mil. The X and Y size can be set independently to define asymmetric pad shapes. 
    • Y-Size - The current Y (vertical) size of the pad, enter a value from 1 to 10000mil. The X and Y size can be set independently to define asymmetric pad shapes.
    • Shape - The basic pad shape. Basic pad shapes include Round, Rectangular, Octagonal, or Rounded Rectangle. The basic shape can be manipulated by changing the X and Y size settings to produce an asymmetrical pad shape.
    • Corner Radius - Available when the Shape is set to Rounded Rectangle. The value is a percentage of half of the shortest side of the pad. As such, a value of 0% corresponds to a rectangular pad, and 100% to a circular pad.
    • Offset From Hole Center (X/Y) - Enter a value to offset the pad land area from the center of the pad hole, by this amount.
  • Full Stack - Different hole sizes and diameters can be edited at each layer (including all signal layers and planes).
    • Edit Full Pad Layer Definitions - Click to open the Pad Layer Editor dialog which provides controls related to pad/via settings for each layer, including pad shape, size, and X/Y location. View the dialog page for more information.

Paste Mask Expansion

An opening in the paste mask is automatically created by the software, the same shape as the pad. This opening can be larger (a positive expansion value) or smaller (a negative expansion value) than the pad itself, as defined by the Paste Mask Expansion setting. Typically paste mask openings are smaller than the pad, but there are exceptions to this.

  • Expansion value from rules - When this option is enabled the paste mask expansion for this pad is defined by the applicable Paste Mask Expansion design rule.
  • Specify expansion value - Enable this option to override the rule and specify the paste mask expansion value for this pad.

Solder Mask Expansions

An opening in the solder mask is automatically created by the software, the same shape as the pad. This opening can be larger (a positive expansion value) or smaller (a negative expansion value) than the pad itself, as defined by the Solder Mask Expansion setting. Typically solder mask openings are larger than the pad, but there are exceptions to this.

  • Expansion value from rules - When this option is enabled the solder mask expansion for this pad is defined by the applicable Solder Mask Expansion design rule.
  • Specify expansion value - Enable this option to override the rule and specify the solder mask expansion values for this pad.
  • Solder Mask From Hole Edge - If the expansion value is being specified here in the Pad dialog, then you can also enable this option to define the solder mask expansion from the edge of the hole, instead of the edge of the pad.
  • Force complete tenting on top - The term tenting means to close off. If this option is enabled then the settings in the applicable solder mask expansion design rule will be overridden, resulting in no opening in the solder mask on the top solder mask layer for this pad. When this option is enabled, the Expansion value from rules and the Specify expansion value options are ignored.
  • Force complete tenting on bottom - The term tenting means to close off. If this option is enabled then the settings in the applicable solder mask expansion design rule will be overridden, resulting in no opening in the solder mask on the bottom solder mask layer for this pad. When this option is enabled, the Expansion value from rules and the Specify expansion value options are ignored.

Paste and Solder masks are shown in the negative, that is, when you see an object on one of those layers it is actually a hole or opening in that layer.

 

Found an issue with this document? Highlight the area, then use Ctrl+Enter to report it.

联系我们

联系原厂或当地办公室

You are reporting an issue with the following selected text
and/or image within the active document:
Altium Designer 免费试用
Altium Designer Free Trial
我们开始吧!首先,您或者您的公司已经在使用Altium Designer了吗?

如果您有任何需求,请点击这里联系获取当地办公室销售代表联系方式。.
Copyright © 2019 Altium Limited

既然您在使用Altium Designer,为何仍需要试用?

如果您有任何需求,请点击这里联系获取当地办公室销售代表联系方式。.
Copyright © 2019 Altium Limited

好的,实际上您无需下载一个试用版本。

点击下方按钮下载最新版本的Altium Designer安装包

下载Altium Designer 安装包

如果您有任何需求,请点击这里联系获取当地办公室销售代表联系方式。.
Copyright © 2019 Altium Limited

填写下方表格,获取Altium Designer最新报价。

点击[获取免费试用],并同意我们的隐私政策。您会接收到来自Altium的资讯,并允许其改变您的通知首选项。

如果您是Altium维保期内客户,您不需要下载试用版本。

如果您不是Altium维保客户,请填写下方表格免费试用。

点击[获取免费试用],并同意我们的隐私政策。您会接收到来自Altium的资讯,并允许其改变您的通知首选项。

您为何想要试用Altium Designer?

如果您有任何需求,请点击这里联系获取当地办公室销售代表联系方式。.
Copyright © 2019 Altium Limited

那您来对地方了!请填写下方表格申请试用吧。

点击[获取免费试用],并同意我们的隐私政策。您会接收到来自Altium的资讯,并允许其改变您的通知首选项。

Great News!

Valid students can get their very own 6-month Altium Designer Student License for FREE! Just fill out the form below to request your Student License today.

点击[获取免费试用],并同意我们的隐私政策。您会接收到来自Altium的资讯,并允许其改变您的通知首选项。

好的,您可以下载免费的Altium Designer Viewer查看文档,有效期6个月。

请填写下方表格申请。

点击[获取免费试用],并同意我们的隐私政策。您会接收到来自Altium的资讯,并允许其改变您的通知首选项。

好棒!创作是一件超酷的事情,我们可以为您提供完美的设计软件。

Upverter是一个社区导向的交流平台,专为您这样的创客量身定做。

点击这里看看吧!

如果您有任何需求,请点击这里联系获取当地办公室销售代表联系方式。.
Copyright © 2019 Altium Limited

好的,您可以下载免费的Altium Designer Viewer查看文档,有效期6个月。

请填写下方表格申请。

点击[获取免费试用],并同意我们的隐私政策。您会接收到来自Altium的资讯,并允许其改变您的通知首选项。