PCB_Dlg-ChangeFillFill_AD

This document is no longer available beyond version 17.1. Information can now be found here: Fill Properties for version 24

Applies to Altium Designer version: 17.1

  The Arc dialog, as accessed while placing a standard Arc (left) and as access while placing a Keeptout Arc (right).

Summary

This dialog allows you to modify the attributes of a Fill object. A fill is a rectangular primitive design object that can be placed on any layer, for any design task requiring a rectangular shape.

Access

The Fill dialog can be accessed prior to entering placement mode, from the PCB Editor – Defaults page of the Preferences dialog. This allows the default properties for the fill object to be changed, which will be applied when placing subsequent fills.

During placement (Place » Fill or Place » Keepout » Fill) , the dialog can be accessed by pressing the Tab key.

The Keepout version of the Fill dialog allows designers to speciify Keepout properties for Fill objects. A keepout object is used on a signal layer to create a layer-specific keepout. Layer-specific keepouts are not included during output generation.
While attributes can be modified during placement, bear in mind that these will become the default settings for further placement unless the Permanent option on the PCB Editor – Defaults page of the Preferences dialog is enabled. When this option is enabled, changes made will affect only the object being placed and subsequent objects placed during the same placement session.

After placement, the dialog can be accessed in the following ways:

  • Double-clicking on a fill object.
  • Placing the cursor over a fill object, right-clicking and choosing Properties from the context menu.
  • Using the Edit » Change command and clicking once over a placed fill object.

Options/Controls

  • Corner 1 X/Y - defines the location of the bottom left corner of the Fill, in an un-rotated state.
  • Corner 2 X/Y - defines the location of the top right corner of the Fill, in an un-rotated state.
  • Rotation - the angle that the fill has been rotated. The fill is rotated around the geometric center. Note that when a fill is rotated, the Corner 1 and Corner 2 values are not changed. The minimum angular resolution is 0.001 degrees.

Properties

  • Layer - the layer that the fill is placed on. Fills can be placed on any layer other than the system layers.
  • Net - if the fill is a copper object, choose a Net for the fill. All Nets in the current project will be listed in the drop-down list.
  • Locked - lock the object so that the object cannot be edited graphically.
If attempting to graphically modify an object that has its Locked property enabled, a dialog will appear asking for confirmation to proceed with the edit. If the Protect Locked Objects option is enabled on the PCB Editor – General page of the Preferences dialog, and the Locked option for that design object is enabled as well, then that object cannot be selected or graphically edited. Double click on the locked object directly and disable the Locked property, or disable the Protect Locked Objects option, to graphically edit the object.
  • Solder Mask Expansion - this field allows you to enable and control the expansion to be used with respect to the fill on the Solder Mask layer, to create the required opening in the mask. This opening can be larger (a positive expansion value) or smaller (a negative expansion value) than the fill itself. The following options are available:
    • No Mask - no opening in the solder mask.
    • Expansion value from rules - choose this option to have the solder mask expansion for the fill follow the defined value in the applicable Solder Mask Expansion design rule.
    • Specify expansion value - choose this option to override the applicable design rule and specify the solder mask expansion value for the fill.
  • Paste Mask Expansion - this field allows you to enable and control the expansion to be used with respect to the fill on the Paste Mask layer, to create the required opening in the mask. This opening can be larger (a positive expansion value) or smaller (a negative expansion value) than the fill itself. The following options are available:
    • No Mask - no opening in the paste mask.
    • Expansion value from rules - choose this option to have the paste mask expansion for the fill follow the defined value in the applicable Paste Mask Expansion design rule.
    • Specify expansion value - choose this option to override the applicable design rule and specify the paste mask expansion value for the fill.
Paste and Solder masks are shown in the negative, that is, when you see an object on one of those layers it is actually a hole or opening in that layer.

Keepout Properties

  • Restricted for Layer - Click to open the drop-down menu and select which layer the Keepout is restricted for.
  • Locked - Lock the object so that it cannot be edited graphically.
  • Keepout Restrictions - Select which primitives are affected by the keepout restrictions.  

Quickly change the units of measurement currently used in the dialog between metric (mm) and imperial (mil) using the Ctrl+Q shortcut. This affects the dialog only and does not change the actual measurement unit employed for the board, as determined by the Measurement Unit setting in the Board Options dialog (Design » Board Options).

Примечание

Доступные функциональные возможности зависят от вашего уровня Подписки на ПО Altium Designer.