Altium Designer Documentation

ToggleComponentDisplayMode

Created: December 11, 2020 | Updated: December 28, 2020

Parent page: Schematic Commands

The following pre-packaged resources, derived from this base command, are available:


Applied Parameters: Action=Add

Summary

This command is used to add an additional graphical representation (mode) for the active component. The addition is called an Alternate.

Access

This command can be accessed from the Schematic Library Editor by:

  • Choosing the Tools » Mode » Add command, from the main menus.
  • Clicking the  button on the Mode toolbar.

Use

First ensure that the component you wish to add the additional graphical representation to, is selected in the Components list of the SCH Library panel (and is, therefore, the active component in the main design window).

After launching the command, an additional graphical representation (mode) will be added to the component, labeled Alternate N (where N is the next available number in the range 1-255).

A blank sheet will appear in the main design workspace, ready for you to add the graphics for this representation.

Tips

  1. The current graphical representation for the active component is denoted by an enabled 'tick' icon beside its entry in the main menus or the Mode drop-down list on the Mode toolbar. Note, however, that only the first 20 Alternate graphical modes are listed on the menu and toolbar.


Applied Parameters: Action=Remove

Summary

This command is used to remove the current graphical representation (mode) for the active component. A component can have a default representation - called Normal - and up to 255 additional representations, known as Alternates.

Access

This command can be accessed from the Schematic Library Editor by:

  • Choosing the Tools » Mode » Remove command, from the main menus.
  • Clicking the  button on the Mode toolbar.

Use

First ensure that the component you wish to remove a graphical representation from is selected in the Components list of the SCH Library panel (and is, therefore, the active component in the main design window). Change the current graphical representation (mode) for the component to the one you wish to remove.

After launching the command, a dialog will appear asking for confirmation to delete the active display mode from the active component. Click Yes to proceed - the current graphical representation will be removed from the component and the previous representation will appear in the main design window.

Tips

  1. You can remove any of the graphical representations (Normal and Alternate) that exist for a component.
  2. If the component has one or more Alternate representations and you remove the Normal representation, the first Alternate (Alternate 1) will become the Normal representation. All other Alternates will be renumbered accordingly.
  3. If the component has no Alternate representations and you remove the Normal representation, the confirmation dialog will ask for confirmation to remove the component from the library - clicking Yes will effectively delete the component from the library.
  4. The current graphical representation for the active component is denoted by an enabled 'check' icon beside its entry in the main menus or the Mode drop-down list on the Mode toolbar. Note, however, that only the first 20 Alternate graphical modes are listed on the menu and toolbar.


Applied Parameters: Action=Mode0

Summary

This command is used to change the graphical representation (mode) of the active component to its Normal mode. This is the primary graphical representation of the component. All components have a Normal mode. Components may, in addition, have anywhere up to 255 Alternate graphical representations (Alternate 1 - Alternate 255).

Access

This command can be accessed from the Schematic Library Editor by:

  • Choosing the Tools » Mode » Normal command, from the main menus.
  • Choosing the Normal entry from the Mode drop-down list, on the Mode toolbar.

Use

First ensure that the component you wish to change the graphical representation for is selected in the Components list of the SCH Library panel (and is, therefore, the active component in the main design window).

After launching the command, the graphical representation of the component will be changed to its Normal mode. The associated graphics for this mode will appear in the main design window.

Tips

  1. The current graphical representation for the active component is denoted by an enabled 'tick' icon beside its entry in the main menus or the Mode drop-down list on the Mode toolbar. Note, however, that only the first 20 Alternate graphical modes are listed on the menu and toolbar.


Applied Parameters: Action=Moden (where n is in the range 1 to 20)

Summary

This command is used to change the graphical representation (mode) of the active component to the indicated Alternate representation. All components have a Normal mode. Components may, in addition, have anywhere up to 255 Alternate graphical representations (Alternate 1 - Alternate 255).

Access

The related indexed commands can be accessed in the Schematic Library Editor from:

  • The Tools » Mode sub-menu.
  • The Mode drop-down list on the Mode toolbar.
Note, however, that only the first 20 Alternate graphical modes are listed on the menu and toolbar, as there are only 20 indexed commands. To access Alternate modes higher than this, you would need to do so by cycling forward through the modes using the Next command (on the main menu and toolbar).

Use

First ensure that the component you wish to change the graphical representation for is selected in the Components list of the SCH Library panel (and is, therefore, the active component in the main design window).

After launching the command, the graphical representation (mode) of the component will be changed to the indicated Alternate. The associated graphics for this mode will appear in the main design window.

Tips

  1. The current graphical representation for the active component is denoted by an enabled 'tick' icon beside its entry in the main menus, or the Mode drop-down list on the Mode toolbar.


Applied Parameters: Action=Next

Summary

This command is used to show the next graphical representation (mode) for the active component, where available. All components have a Normal mode. Components may, in addition, have anywhere up to 255 Alternate graphical representations (Alternate 1 - Alternate 255).

Access

This command can be accessed from the Schematic Library Editor by:

  • Choosing the Tools » Mode » Next command, from the main menus.
  • Clicking the  button on the Mode toolbar.
The command will not be available when there are no more subsequent Alternate representations to show, or if a component has no Alternate representations to begin with.

Use

First ensure that the component whose graphical representations you wish to browse/change is selected in the Components list of the SCH Library panel (and is, therefore, the active component in the main design window).

After launching the command, the next Alternate graphical representation for the component will be displayed in the main design window.

Tips

  1. The current graphical representation for the active component is denoted by an enabled 'tick' icon beside its entry in the main menus, or the Mode drop-down list on the Mode toolbar.


Applied Parameters: Action=Previous

Summary

This command is used to show the previous graphical representation (mode) for the active component, where available. All components have a Normal mode. Components may, in addition, have anywhere up to 255 Alternate graphical representations (Alternate 1 - Alternate 255).

Access

This command can be accessed from the Schematic Library Editor by:

  • Choosing the Tools » Mode » Previous command from the main menus.
  • Clicking the  button on the Mode toolbar.
The command will be unavailable once the Normal representation becomes the current display.

Use

First ensure that the component whose graphical representations you wish to browse/change is selected in the Components list of the SCH Library panel (and is, therefore, the active component in the main design window).

After launching the command, the previous Alternate graphical representation for the component will be displayed in the main design window.

Tips

  1. The current graphical representation for the active component is denoted by an enabled 'tick' icon beside its entry in the main menus, or the Mode drop-down list on the Mode toolbar.
 

Applied Parameters: Action=Rename

Summary

This command is used to rename the selected symbol graphic. 

Access

This command can be accessed from the Schematic Library Editor by:

  • Choosing the Tools » Mode » Rename command from the main menus.
  • Clicking Rename on the Mode toolbar.

Use

First ensure that the graphic symbol you wish to rename is selected in the Components list of the SCH Library panel (and is, therefore, the active component in the main design window). 

After launching the command, the Rename Alternate Representation dialog will appear. Enter the new name for the selected symbol and click Ok. The new alternate name will appear in the Mode drop-down list from the Graphical section of the Properties panel when the component is placed on the schematic.

Found an issue with this document? Highlight the area, then use Ctrl+Enter to report it.

联系我们

联系原厂或当地办公室

We're sorry to hear the article wasn't helpful to you.
Could you take a moment to tell us why?
200 characters remaining
You are reporting an issue with the following selected text
and/or image within the active document:
Altium Designer 免费试用
Altium Designer Free Trial
我们开始吧!首先,您或者您的公司已经在使用Altium Designer了吗?

如果您有任何需求,请点击这里联系获取当地办公室销售代表联系方式。.
Copyright © 2019 Altium Limited

既然您在使用Altium Designer,为何仍需要试用?

如果您有任何需求,请点击这里联系获取当地办公室销售代表联系方式。.
Copyright © 2019 Altium Limited

好的,实际上您无需下载一个试用版本。

点击下方按钮下载最新版本的Altium Designer安装包

下载Altium Designer 安装包

如果您有任何需求,请点击这里联系获取当地办公室销售代表联系方式。.
Copyright © 2019 Altium Limited

填写下方表格,获取Altium Designer最新报价。

点击[获取免费试用],并同意我们的隐私政策。您会接收到来自Altium的资讯,并允许其改变您的通知首选项。

如果您是Altium维保期内客户,您不需要下载试用版本。

如果您不是Altium维保客户,请填写下方表格免费试用。

点击[获取免费试用],并同意我们的隐私政策。您会接收到来自Altium的资讯,并允许其改变您的通知首选项。

您为何想要试用Altium Designer?

如果您有任何需求,请点击这里联系获取当地办公室销售代表联系方式。.
Copyright © 2019 Altium Limited

那您来对地方了!请填写下方表格申请试用吧。

点击[获取免费试用],并同意我们的隐私政策。您会接收到来自Altium的资讯,并允许其改变您的通知首选项。

Great News!

Valid students can get their very own 6-month Altium Designer Student License for FREE! Just fill out the form below to request your Student License today.

点击[获取免费试用],并同意我们的隐私政策。您会接收到来自Altium的资讯,并允许其改变您的通知首选项。

好的,您可以下载免费的Altium Designer Viewer查看文档,有效期6个月。

请填写下方表格申请。

点击[获取免费试用],并同意我们的隐私政策。您会接收到来自Altium的资讯,并允许其改变您的通知首选项。

好棒!创作是一件超酷的事情,我们可以为您提供完美的设计软件。

Upverter是一个社区导向的交流平台,专为您这样的创客量身定做。

点击这里看看吧!

如果您有任何需求,请点击这里联系获取当地办公室销售代表联系方式。.
Copyright © 2019 Altium Limited

好的,您可以下载免费的Altium Designer Viewer查看文档,有效期6个月。

请填写下方表格申请。

点击[获取免费试用],并同意我们的隐私政策。您会接收到来自Altium的资讯,并允许其改变您的通知首选项。